C++ HAL_RCC_OscConfig函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中HAL_RCC_OscConfig函数的典型用法代码示例。如果您正苦于以下问题：C++ HAL_RCC_OscConfig函数的具体用法？C++ HAL_RCC_OscConfig怎么用？C++ HAL_RCC_OscConfig使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了HAL_RCC_OscConfig函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: SystemClock_Config

/** System Clock Configuration
*/
void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct;
  RCC_ClkInitTypeDef RCC_ClkInitStruct;

  __PWR_CLK_ENABLE();

  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
//  RCC_OscInitStruct.OscillatorType |= RCC_OSCILLATORTYPE_LSI;  // uncomment when LSI clock is used for RTC
//  RCC_OscInitStruct.LSIState = RCC_LSI_ON;        // uncomment when LSI Clock is used for RTC
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLM = 5;
  RCC_OscInitStruct.PLL.PLLN = 210;
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
  RCC_OscInitStruct.PLL.PLLQ = 4;
  HAL_RCC_OscConfig(&RCC_OscInitStruct);

  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
                              |RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);

#ifdef USE_STM32F4_RTC
  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_RTC;
  PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_HSE_DIV8;  // Comment this line if you want to use LSI clock
//  PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_LSI;     // Remove comment if you want to use LSI clock
  HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);
#endif /* USE_STM32F4_RTC */
}

开发者ID:glocklueng，项目名称:STM32F4-Dev，代码行数:38，代码来源:main.c

示例2: SystemClock_Config

/** System Clock Configuration */
void SystemClock_Config(void)
{
  RCC_OscInitTypeDef RCC_OscInitStruct;
  RCC_ClkInitTypeDef RCC_ClkInitStruct;

  __PWR_CLK_ENABLE();

  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

  RCC_OscInitStruct.OscillatorType 	= RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState 			 	= RCC_HSE_ON;
  RCC_OscInitStruct.PLL.PLLState 		= RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource 	= RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLM 				= 8;
  RCC_OscInitStruct.PLL.PLLN 				= 336;
  RCC_OscInitStruct.PLL.PLLP 				= RCC_PLLP_DIV2;
  RCC_OscInitStruct.PLL.PLLQ 				= 7;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK){Error_Handler(RCC_CONFIG_FAIL);};

  RCC_ClkInitStruct.ClockType 			= RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource 		= RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider 	= RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider 	= RCC_HCLK_DIV4;
  RCC_ClkInitStruct.APB2CLKDivider 	= RCC_HCLK_DIV2;
  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5)!= HAL_OK){Error_Handler(RCC_CONFIG_FAIL);};
	
	/*Configures SysTick to provide 500Hz interval interrupts. (Read ADC once in two times)*/
  HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/500);

	/* This function sets the source clock for the internal SysTick Timer to be the maximum,
	   in our case, HCLK is now 168MHz*/
  HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK);

  /* SysTick_IRQn interrupt configuration */
  HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
}

开发者ID:Lone-L，项目名称:MicroP_Labs，代码行数:37，代码来源:main.c

示例3: SystemClock_Config

/** System Clock Configuration
*/
void SystemClock_Config(void)
{

  RCC_OscInitTypeDef RCC_OscInitStruct;
  RCC_ClkInitTypeDef RCC_ClkInitStruct;

  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9;
  HAL_RCC_OscConfig(&RCC_OscInitStruct);

  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);

  __HAL_RCC_AFIO_CLK_ENABLE();

}

开发者ID:AlexanderHazard，项目名称:lcd_driver，代码行数:26，代码来源:main.c

示例4: SystemClock_Config

/** System Clock Configuration
*/
void SystemClock_Config(void)
{

  RCC_OscInitTypeDef RCC_OscInitStruct;
  RCC_ClkInitTypeDef RCC_ClkInitStruct;
  RCC_PeriphCLKInitTypeDef PeriphClkInit;

  __PWR_CLK_ENABLE();

  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_MSI;
  RCC_OscInitStruct.MSIState = RCC_MSI_ON;
  RCC_OscInitStruct.MSICalibrationValue = 0;
  RCC_OscInitStruct.MSIClockRange = RCC_MSIRANGE_5;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  HAL_RCC_OscConfig(&RCC_OscInitStruct);

  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_MSI;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0);

  PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART2;
  PeriphClkInit.Usart2ClockSelection = RCC_USART2CLKSOURCE_PCLK1;
  HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit);

  HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/1000);

  HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK);

  /* SysTick_IRQn interrupt configuration */
  HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
}

开发者ID:doebbertt，项目名称:mastering-stm32，代码行数:38，代码来源:main-ex1.c

示例5: SystemClock_Config

/** System Clock Configuration
*/
void SystemClock_Config(void)
{

  RCC_OscInitTypeDef RCC_OscInitStruct;
  RCC_ClkInitTypeDef RCC_ClkInitStruct;

  __PWR_CLK_ENABLE();

  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSICalibrationValue = 16;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
  RCC_OscInitStruct.PLL.PLLM = 8;
  RCC_OscInitStruct.PLL.PLLN = 100;
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
  RCC_OscInitStruct.PLL.PLLQ = 4;
  HAL_RCC_OscConfig(&RCC_OscInitStruct);

  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
                              |RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV4;
  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);

  HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/1000);

  HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK);

  /* SysTick_IRQn interrupt configuration */
  HAL_NVIC_SetPriority(SysTick_IRQn, 0, 0);
}

开发者ID:cjackie，项目名称:Quadcopter-Flight-Controller，代码行数:38，代码来源:main.c

示例6: PLL

/*
System Clock source            = PLL (HSE)
SYSCLK(Hz)                     = 48000000
HCLK(Hz)                       = 48000000
AHB Prescaler                  = 1
APB1 Prescaler                 = 1
HSE Frequency(Hz)              = 8000000
PREDIV                         = 2
PLLMUL                         = 12
Flash Latency(WS)              = 1
*/
void HAL_MspInit( void )
{
  RCC_ClkInitTypeDef RCC_ClkInitStruct;
  RCC_OscInitTypeDef RCC_OscInitStruct;
  HAL_StatusTypeDef state = HAL_OK;

  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState       = RCC_HSE_ON;
  RCC_OscInitStruct.PLL.PLLState   = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource  = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PREDIV     = RCC_PREDIV_DIV2;
  RCC_OscInitStruct.PLL.PLLMUL     = RCC_PLL_MUL12;
  state = HAL_RCC_OscConfig(&RCC_OscInitStruct);
  if(state != HAL_OK)
    while(1) { ; }

  RCC_ClkInitStruct.ClockType      = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1);
  RCC_ClkInitStruct.SYSCLKSource   = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider  = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
  state = HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
  if(state != HAL_OK)
    while(1) { ; }
}

开发者ID:dongruibin，项目名称:MungBeanSprout，代码行数:35，代码来源:stm32f0_msp.c

示例7: SystemClock_Config

/**
  * @brief  System Clock Configuration
  *         The system Clock is configured as follow : 
  *            System Clock source            = PLL (HSE)
  *            SYSCLK(Hz)                     = 180000000
  *            HCLK(Hz)                       = 180000000
  *            AHB Prescaler                  = 1
  *            APB1 Prescaler                 = 4
  *            APB2 Prescaler                 = 2
  *            HSE Frequency(Hz)              = 25000000
  *            PLL_M                          = 25
  *            PLL_N                          = 360
  *            PLL_P                          = 2
  *            PLL_Q                          = 7
  *            VDD(V)                         = 3.3
  *            Main regulator output voltage  = Scale1 mode
  *            Flash Latency(WS)              = 5
  * @param  None
  * @retval None
  */
static void SystemClock_Config(void)
{
  RCC_ClkInitTypeDef RCC_ClkInitStruct;
  RCC_OscInitTypeDef RCC_OscInitStruct;

  /* Enable Power Control clock */
  __HAL_RCC_PWR_CLK_ENABLE();

  /* The voltage scaling allows optimizing the power consumption when the device is 
     clocked below the maximum system frequency, to update the voltage scaling value 
     regarding system frequency refer to product datasheet.  */
  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
  
  /* Enable HSE Oscillator and activate PLL with HSE as source */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLM = 25;
  RCC_OscInitStruct.PLL.PLLN = 360;
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
  RCC_OscInitStruct.PLL.PLLQ = 7;
  HAL_RCC_OscConfig(&RCC_OscInitStruct);
 
  /* Activate the Over-Drive mode */
  HAL_PWREx_EnableOverDrive();
 
  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 
  clocks dividers */
  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;  
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;  
  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
}

开发者ID:451506709，项目名称:automated_machine，代码行数:56，代码来源:main.c

示例8: HAL_RTC_MspInit

/**
  * @brief RTC MSP Initialization
  *        This function configures the hardware resources used in this example
  * @param hrtc: RTC handle pointer
  *
  * @note  Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select
  *        the RTC clock source; in this case the Backup domain will be reset in
  *        order to modify the RTC Clock source, as consequence RTC registers (including
  *        the backup registers) and RCC_BDCR register are set to their reset values.
  *
  * @retval None
  */
void HAL_RTC_MspInit(RTC_HandleTypeDef *hrtc)
{
  RCC_OscInitTypeDef        RCC_OscInitStruct;
  RCC_PeriphCLKInitTypeDef  PeriphClkInitStruct;

  /*##-1- Enables the PWR Clock and Enables access to the backup domain ###################################*/
  /* To change the source clock of the RTC feature (LSE, LSI), You have to:
     - Enable the power clock using __HAL_RCC_PWR_CLK_ENABLE()
     - Enable write access using HAL_PWR_EnableBkUpAccess() function before to
       configure the RTC clock source (to be done once after reset).
     - Reset the Back up Domain using __HAL_RCC_BACKUPRESET_FORCE() and
       __HAL_RCC_BACKUPRESET_RELEASE().
     - Configure the needed RTc clock source */
  __HAL_RCC_PWR_CLK_ENABLE();
  HAL_PWR_EnableBkUpAccess();

  /*##-2- Configure LSE as RTC clock source ###################################*/
  RCC_OscInitStruct.OscillatorType =  RCC_OSCILLATORTYPE_LSI;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  RCC_OscInitStruct.LSIState = RCC_LSI_ON;
  if(HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    Error_Handler();
  }

  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_RTC;
  PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_LSI;
  if(HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct) != HAL_OK)
  {
    Error_Handler();
  }

  /*##-3- Enable RTC peripheral Clocks #######################################*/
  /* Enable RTC Clock */
  __HAL_RCC_RTC_ENABLE();
}

开发者ID:Joe-Merten，项目名称:Stm32-Tools-Evaluation，代码行数:48，代码来源:stm32f4xx_hal_msp.c

示例9: rtc_free

void rtc_free(void) {
    // Enable Power clock
    __PWR_CLK_ENABLE();

    // Enable access to Backup domain
    HAL_PWR_EnableBkUpAccess();

    // Reset Backup domain
    __HAL_RCC_BACKUPRESET_FORCE();
    __HAL_RCC_BACKUPRESET_RELEASE();

    // Disable access to Backup domain
    HAL_PWR_DisableBkUpAccess();

    // Disable LSI and LSE clocks
    RCC_OscInitTypeDef RCC_OscInitStruct;
    RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_LSI | RCC_OSCILLATORTYPE_LSE;
    RCC_OscInitStruct.PLL.PLLState   = RCC_PLL_NONE;
    RCC_OscInitStruct.LSIState       = RCC_LSI_OFF;
    RCC_OscInitStruct.LSEState       = RCC_LSE_OFF;
    HAL_RCC_OscConfig(&RCC_OscInitStruct);

    rtc_inited = 0;
}

开发者ID:AllenMcAfee，项目名称:Smoothie2，代码行数:24，代码来源:rtc_api.c

示例10: SetSysClock

/*
Set SYSCLK=84MHZ
 */
void SetSysClock(void)
{

    RCC_OscInitTypeDef RCC_OscInitStruct;
    RCC_ClkInitTypeDef RCC_ClkInitStruct;

    __HAL_RCC_PWR_CLK_ENABLE();

    __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE3);

    RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
    RCC_OscInitStruct.HSEState = RCC_HSE_ON;
    RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
    RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
#ifdef USE_DEBUG_8MHz_XTAL
    RCC_OscInitStruct.PLL.PLLM = 8;
#else
    RCC_OscInitStruct.PLL.PLLM = 12;
#endif
    RCC_OscInitStruct.PLL.PLLN = 336;
    RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4;
    RCC_OscInitStruct.PLL.PLLQ = 7;
    HAL_RCC_OscConfig(&RCC_OscInitStruct);


    RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_PCLK1
                                  | RCC_CLOCKTYPE_PCLK2;
    RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
    RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
    RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
    RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
    HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);

    // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);

}

开发者ID:toyowata，项目名称:mbed，代码行数:39，代码来源:system_clock.c

示例11: SystemClock_Config

/**
 * @brief  System Clock Configuration
 * @param  None
 * @retval None
 */
void SystemClock_Config(void)
{
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  
  /* MSI is enabled after System reset, activate PLL with MSI as source */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_MSI;
  RCC_OscInitStruct.MSIState = RCC_MSI_ON;
  RCC_OscInitStruct.MSIClockRange = RCC_MSIRANGE_6;
  RCC_OscInitStruct.MSICalibrationValue = RCC_MSICALIBRATION_DEFAULT;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_MSI;
  RCC_OscInitStruct.PLL.PLLM = 1;
  RCC_OscInitStruct.PLL.PLLN = 40;
  RCC_OscInitStruct.PLL.PLLR = 2;
  RCC_OscInitStruct.PLL.PLLP = 7;
  RCC_OscInitStruct.PLL.PLLQ = 4;
  if(HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }
  
  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
     clocks dividers */
  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
  if(HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }
}

开发者ID:asebak，项目名称:IMU，代码行数:41，代码来源:cube_hal_l4.c

示例12: SystemClock_Config

/** System Clock Configuration
*/
void SystemClock_Config(void)
{

  RCC_OscInitTypeDef RCC_OscInitStruct;
  RCC_ClkInitTypeDef RCC_ClkInitStruct;
  RCC_PeriphCLKInitTypeDef PeriphClkInitStruct;

  __PWR_CLK_ENABLE();

  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_LSI | RCC_OSCILLATORTYPE_HSE;  //add RCC_OSCILLATORTYPE_LSI for LSI Clock
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.LSIState = RCC_LSI_ON;        // Added for LSI Clock
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLM = 8;
  RCC_OscInitStruct.PLL.PLLN = 336;
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
  RCC_OscInitStruct.PLL.PLLQ = 7;
  HAL_RCC_OscConfig(&RCC_OscInitStruct);

  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
                              |RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);

  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_RTC;
//  PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_HSE_DIV8;  //Comment this line if you want to use LSI clock
  PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_LSI;     // Remove comment if you want to use LSI clock
  HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct);

}

开发者ID:glocklueng，项目名称:STM32F4-Dev，代码行数:38，代码来源:main.c

示例13: PLL

/*
System Clock source            = PLL (HSE)
SYSCLK(Hz)                     = 72000000
HCLK(Hz)                       = 72000000
AHB Prescaler                  = 1
APB1 Prescaler                 = 2
APB2 Prescaler                 = 1
HSE Frequency(Hz)              = 8000000 // HSE_VALUE
HSE PREDIV                     = 1
PLLMUL                         = RCC_PLL_MUL9 (9)
Flash Latency(WS)              = 2
*/
void HAL_MspInit( void )
{
  RCC_ClkInitTypeDef RCC_ClkInitStruct;
  RCC_OscInitTypeDef RCC_OscInitStruct;

  /* Enable HSE Oscillator and activate PLL with HSE as source */
  RCC_OscInitStruct.OscillatorType  = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState        = RCC_HSE_ON;
  RCC_OscInitStruct.HSEPredivValue  = RCC_HSE_PREDIV_DIV1;
  RCC_OscInitStruct.PLL.PLLState    = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource   = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLMUL      = RCC_PLL_MUL9;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
    while (1) { ; }

  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
  RCC_ClkInitStruct.ClockType       = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
  RCC_ClkInitStruct.SYSCLKSource    = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider   = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider  = RCC_HCLK_DIV2;  
  RCC_ClkInitStruct.APB2CLKDivider  = RCC_HCLK_DIV1;
  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)
    while(1) { ; }
}

开发者ID:KitSprout，项目名称:RedBeanSprout，代码行数:36，代码来源:stm32f3_msp.c

示例14: HAL_RTC_MspInit

/**
  * @brief RTC MSP Initialization 
  *        This function configures the hardware resources used in this example
  * @param hrtc: RTC handle pointer
  * 
  * @note  Care must be taken when HAL_RCCEx_PeriphCLKConfig() is used to select 
  *        the RTC clock source; in this case the Backup domain will be reset in  
  *        order to modify the RTC Clock source, as consequence RTC registers (including 
  *        the backup registers) and RCC_BDCR register are set to their reset values.
  *             
  * @retval None
  */
void HAL_RTC_MspInit(RTC_HandleTypeDef *hrtc)
{
  RCC_OscInitTypeDef        RCC_OscInitStruct;
  RCC_PeriphCLKInitTypeDef  PeriphClkInitStruct;
  
  /*##-1- Enables the PWR Clock and Enables access to the backup domain ###################################*/
  /* To change the source clock of the RTC feature (LSE, LSI), You have to:
     - Enable the power clock using __HAL_RCC_PWR_CLK_ENABLE()
     - Enable write access using HAL_PWR_EnableBkUpAccess() function before to 
       configure the RTC clock source (to be done once after reset).
     - Reset the Back up Domain using __HAL_RCC_BACKUPRESET_FORCE() and 
       __HAL_RCC_BACKUPRESET_RELEASE().
     - Configure the needed RTC clock source */
  __HAL_RCC_PWR_CLK_ENABLE();
  HAL_PWR_EnableBkUpAccess();

  /*##-2- Configure LSE/LSI as RTC clock source ###############################*/
#ifdef RTC_CLOCK_SOURCE_LSE
  
  RCC_OscInitStruct.OscillatorType =  RCC_OSCILLATORTYPE_LSI | RCC_OSCILLATORTYPE_LSE;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  RCC_OscInitStruct.LSEState = RCC_LSE_ON;
  RCC_OscInitStruct.LSIState = RCC_LSI_OFF;
  if(HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  { 
    Error_Handler();
  }
  
  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_RTC;
  PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_LSE;
  if(HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct) != HAL_OK)
  { 
    Error_Handler();
  }
#elif defined (RTC_CLOCK_SOURCE_LSI)  
  RCC_OscInitStruct.OscillatorType =  RCC_OSCILLATORTYPE_LSI | RCC_OSCILLATORTYPE_LSE;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  RCC_OscInitStruct.LSIState = RCC_LSI_ON;
  RCC_OscInitStruct.LSEState = RCC_LSE_OFF;
  if(HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  { 
    Error_Handler();
  }

  PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_RTC;
  PeriphClkInitStruct.RTCClockSelection = RCC_RTCCLKSOURCE_LSI;
  if(HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct) != HAL_OK)
  { 
    Error_Handler();
  }
#else
#error Please select the RTC Clock source inside the main.h file
#endif /*RTC_CLOCK_SOURCE_LSE*/
  
  /*##-3- Enable RTC peripheral Clocks #######################################*/ 
  /* Enable RTC Clock */ 
  __HAL_RCC_RTC_ENABLE(); 
  
  /*##-4- Configure the NVIC for RTC Tamper ###################################*/
  HAL_NVIC_SetPriority(TAMP_STAMP_IRQn, 0x0F, 0);
  HAL_NVIC_EnableIRQ(TAMP_STAMP_IRQn);
}

开发者ID:451506709，项目名称:automated_machine，代码行数:74，代码来源:stm32f4xx_hal_msp.c

示例15: SystemClock_Config

/**
  * @brief  System Clock Configuration
  *         The system Clock is configured as follow:
  *  
  *            HSI48 used as clock source (USE_CLKSOURCE_CRSHSI48 defined in main.h)
  *              - System Clock source            = HSI48
  *              - SYSCLK(Hz)                     = 48000000
  *              - HCLK(Hz)                       = 48000000
  *              - AHB Prescaler                  = 1
  *              - APB1 Prescaler                 = 1
  *              - Flash Latency(WS)              = 1
  *
  *              - PLL(HSE) used as clock source (USE_CLKSOURCE_PLL defined in main.h)
  *              - System Clock source            = PLL (HSE)
  *              - SYSCLK(Hz)                     = 48000000
  *              - HCLK(Hz)                       = 48000000
  *              - AHB Prescaler                  = 1
  *              - APB1 Prescaler                 = 1
  *              - HSE Frequency(Hz)              = 8000000
  *              - PREDIV                         = 1
  *              - PLLMUL                         = 6
  *              - Flash Latency(WS)              = 1
  *
  * @param  None
  * @retval None
  */
static void SystemClock_Config(void)
{
  RCC_ClkInitTypeDef RCC_ClkInitStruct;
  RCC_OscInitTypeDef RCC_OscInitStruct;
  
#if defined (USE_CLKSOURCE_CRSHSI48)
  static RCC_CRSInitTypeDef RCC_CRSInitStruct;
#endif
  
#if defined (USE_CLKSOURCE_CRSHSI48)
  
  /* Enable HSI48 Oscillator to be used as system clock source */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI48;
  HAL_RCC_OscConfig(&RCC_OscInitStruct); 
  
  /* Select HSI48 as system clock source and configure the HCLK and PCLK1 
  clock dividers */
  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1);
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI48;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;  
  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
  
  /*Configure the clock recovery system (CRS)**********************************/
  
  /*Enable CRS Clock*/
  __CRS_CLK_ENABLE(); 
  
  /* Default Synchro Signal division factor (not divided) */
  RCC_CRSInitStruct.Prescaler = RCC_CRS_SYNC_DIV1;
  
  /* Set the SYNCSRC[1:0] bits according to CRS_Source value */
  RCC_CRSInitStruct.Source = RCC_CRS_SYNC_SOURCE_USB;
  
  /* HSI48 is synchronized with USB SOF at 1KHz rate */
  RCC_CRSInitStruct.ReloadValue =  __HAL_RCC_CRS_CALCULATE_RELOADVALUE(48000000, 1000);
  RCC_CRSInitStruct.ErrorLimitValue = RCC_CRS_ERRORLIMIT_DEFAULT;
  
  /* Set the TRIM[5:0] to the default value*/
  RCC_CRSInitStruct.HSI48CalibrationValue = 0x20; 
  
  /* Start automatic synchronization */ 
  HAL_RCCEx_CRSConfig (&RCC_CRSInitStruct);
  
#elif defined (USE_CLKSOURCE_PLL)
  
  /* Enable HSE Oscillator and activate PLL with HSE as source
  PLLCLK = (8 * 6) / 1) = 48 MHz */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL6;
  RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1;
  HAL_RCC_OscConfig(&RCC_OscInitStruct); 
  
  /* Select PLL as system clock source and configure the HCLK and PCLK1 
  clock dividers */
  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1);
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;  
  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_1);
  
#endif /*USE_CLKSOURCE_CRSHSI48*/
}

开发者ID:GreyCardinalRus，项目名称:stm32-cube，代码行数:92，代码来源:main.c

示例16: SystemClockHSE_Config

/**
  * @brief  System Clock Configuration
  *         The system Clock is configured as follow : 
  *            System Clock source            = PLL (HSE_CRYSTAL or HSE_BYPASS) 
  *            SYSCLK(Hz)                     = 180000000
  *            HCLK(Hz)                       = 180000000
  *            AHB Prescaler                  = 1
  *            APB1 Prescaler                 = 4
  *            APB2 Prescaler                 = 2
  *            HSE Frequency(Hz)              = 8000000
  *            PLL_M                          = 8
  *            PLL_N                          = 360
  *            PLL_P                          = 2
  *            PLL_Q                          = 7
  *            VDD(V)                         = 3.3
  *            Main regulator output voltage  = Scale1 mode
  *            Flash Latency(WS)              = 5
  * @param  None
  * @retval None
  */
void SystemClockHSE_Config(void)
{
  RCC_ClkInitTypeDef RCC_ClkInitStruct;
  RCC_OscInitTypeDef RCC_OscInitStruct;
  HAL_StatusTypeDef ret = HAL_OK;
    
  /* Enable Power Control clock */
  __HAL_RCC_PWR_CLK_ENABLE();
  
  /* The voltage scaling allows optimizing the power consumption when the device is 
     clocked below the maximum system frequency, to update the voltage scaling value 
     regarding system frequency refer to product datasheet.  */
  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

  /* -1- Select HSI as system clock source to allow modification of the PLL configuration */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI;
  if(HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
  {
    Error_Handler();
  }
  
  /* -2- Enable HSE Oscillator, select it as PLL source and finally activate the PLL */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  
#ifdef HSE_CRYSTAL  
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
#elif defined (HSE_BYPASS)
  RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
#endif /* HSE_CRYSTAL */
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  RCC_OscInitStruct.PLL.PLLM = 8;
  RCC_OscInitStruct.PLL.PLLN = 360;
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
  RCC_OscInitStruct.PLL.PLLQ = 7;
  RCC_OscInitStruct.PLL.PLLR = 6;
  if(HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }
  
   /* Activate the OverDrive to reach the 180 MHz Frequency */  
  ret = HAL_PWREx_EnableOverDrive();
  if(ret != HAL_OK)
  {
    while(1) { ; }
  }
  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 
     clocks dividers */
  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;  
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;  
  if(HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5) != HAL_OK)
  {
    Error_Handler();
  }
  
  /* -4- Optional: Disable HSI Oscillator (if the HSI is no more needed by the application) */
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  if(HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }
}

开发者ID:Lembed，项目名称:STM32CubeF4-mirrors，代码行数:91，代码来源:main.c

示例17: attribute

void __attribute__((weak)) SystemClock_Config(void) //TODO: rewrite in order to sysinit.c
{
  __PWR_CLK_ENABLE();

  __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

  RCC_OscInitTypeDef RCC_OscInitStruct;

#if defined(HSE_VALUE) && (HSE_VALUE != 0)
  // Enable HSE Oscillator and activate PLL with HSE as source.
  // This is tuned for STM32F4-DISCOVERY; update it for your board.
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
  RCC_OscInitStruct.HSEState = RCC_HSE_ON;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
  // This assumes the HSE_VALUE is a multiple of 1 MHz. If this is not
  // your case, you have to recompute these PLL constants.
  RCC_OscInitStruct.PLL.PLLM = (HSE_VALUE/1000000u);
#else
  // Use HSI and activate PLL with HSI as source.
  // This is tuned for NUCLEO-F411; update it for your board.
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  // 16 is the average calibration value, adjust for your own board.
  RCC_OscInitStruct.HSICalibrationValue = 16;
  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
  // This assumes the HSI_VALUE is a multiple of 1 MHz. If this is not
  // your case, you have to recompute these PLL constants.
  RCC_OscInitStruct.PLL.PLLM = (HSI_VALUE/1000000u);
#endif

  RCC_OscInitStruct.PLL.PLLN = 336;
#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; /* 84 MHz */
#elif defined(STM32F427xx) || defined(STM32F437xx) || defined(STM32F429xx) || defined(STM32F439xx)
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; /* 168 MHz */
#elif defined(STM32F405xx) || defined(STM32F415xx) || defined(STM32F407xx) || defined(STM32F417xx)
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; /* 168 MHz */
#elif defined(STM32F446xx)
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2; /* 168 MHz */
#else
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4; /* 84 MHz, conservative */
#endif
  RCC_OscInitStruct.PLL.PLLQ = 7; /* To make USB work. */
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  HAL_RCC_OscConfig(&RCC_OscInitStruct);

  RCC_ClkInitTypeDef RCC_ClkInitStruct;
  // Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2
  // clocks dividers
  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK
      | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
#if defined(STM32F401xC) || defined(STM32F401xE) || defined(STM32F411xE)
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);
#else
  // This is expected to work for most large cores.
  // Check and update it for your own configuration.
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
  HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
#endif

  HAL_SYSTICK_Config(HAL_RCC_GetHCLKFreq()/1000);

  HAL_SYSTICK_CLKSourceConfig(SYSTICK_CLKSOURCE_HCLK);
}

开发者ID:legath，项目名称:uberdashboard-src，代码行数:70，代码来源:init_hw.c

示例18: SystemClock_Config

  /**
  * @brief  System Clock Configuration
  *         The system Clock is configured as follow :
  *            System Clock source            = PLL (HSE or HSI)
  *            SYSCLK(Hz)                     = XPLL
  *            HCLK(Hz)                       = XPLL
  *            AHB Prescaler                  = 1
  *            APB1 Prescaler                 = 4
  *            APB2 Prescaler                 = 2
  *            HSE Frequency(Hz)              = XHSI
  *            PLL_M                          = 8
  *            PLL_N                          = XPLL * 2
  *            PLL_P                          = 2
  *            PLL_Q                          = 7
  *            PLL_R                          = 6
  *            VDD(V)                         = 3.3
  *            Main regulator output voltage  = Scale1 mode
  *            Flash Latency(WS)              = 7
  * @param  None
  * @retval None
  */
static void SystemClock_Config(unsigned long int_osc_freq, unsigned long ext_osc_freq, unsigned long core_freq)
{
  RCC_ClkInitTypeDef RCC_ClkInitStruct;
  memset(&RCC_ClkInitStruct, 0, sizeof(RCC_ClkInitTypeDef));
  RCC_OscInitTypeDef RCC_OscInitStruct;
  memset(&RCC_OscInitStruct, 0, sizeof(RCC_OscInitTypeDef));
  HAL_StatusTypeDef ret = HAL_OK;

  /* Enable Power Control clock */
	__HAL_RCC_PWR_CLK_ENABLE();

  /* The voltage scaling allows optimizing the power consumption when the device is
     clocked below the maximum system frequency, to update the voltage scaling value
     regarding system frequency refer to product datasheet.  */
	__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);

  /* Enable HSE Oscillator and activate PLL with HSE as source */
	if(EXTERNAL_CLOCK_VALUE == 0)
	{
		if(ext_osc_freq == 0)
		{
			RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
			RCC_OscInitStruct.HSIState = RCC_HSI_ON;
			RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
			RCC_OscInitStruct.PLL.PLLM = int_osc_freq /1000000;
		}
		else
		{
			RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
			RCC_OscInitStruct.HSEState = RCC_HSE_ON;
			RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
#if defined(USE_STM32469I_DISCO_REVA)
			RCC_OscInitStruct.PLL.PLLM = 25;
#else
			RCC_OscInitStruct.PLL.PLLM = ext_osc_freq /1000000;
#endif /* USE_STM32469I_DISCO_REVA */
		}
	}
	else
	{
		RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
		RCC_OscInitStruct.HSEState = RCC_HSE_BYPASS;
		RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
		RCC_OscInitStruct.PLL.PLLM = EXTERNAL_CLOCK_VALUE /1000000;
	}
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
  RCC_OscInitStruct.PLL.PLLN = (core_freq * 2) / 1000000;
  RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
  RCC_OscInitStruct.PLL.PLLQ = 9;
  RCC_OscInitStruct.PLL.PLLR = 7;

  ret = HAL_RCC_OscConfig(&RCC_OscInitStruct);
  if(ret != HAL_OK)
  {
    while(1) { ; }
  }

//#if defined(STM32F469xx) || defined(STM32F479xx)
  /* Activate the OverDrive to reach the 180 MHz Frequency */
  ret = HAL_PWREx_EnableOverDrive();
  if(ret != HAL_OK)
  {
    while(1) { ; }
  }
//#endif

  /* Select PLL as system clock source and configure the HCLK, PCLK1 and PCLK2 clocks dividers */
  RCC_ClkInitStruct.ClockType = (RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2);
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;

  ret = HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7);
  if(ret != HAL_OK)
  {
    while(1) { ; }
  }
  PLL_REF_CLK =	RCC_OscInitStruct.PLL.PLLM * 1000000;
//.........这里部分代码省略.........

开发者ID:MorgothCreator，项目名称:mSdk，代码行数:101，代码来源:core_init.c

示例19: TM_RCC_InitSystem

TM_RCC_Result_t TM_RCC_InitSystem(void) {
	RCC_ClkInitTypeDef RCC_ClkInitStruct;
	RCC_OscInitTypeDef RCC_OscInitStruct;

#if defined(STM32F7xx)
	/* Invalidate I-Cache : ICIALLU register */
	SCB_InvalidateICache();

	/* Enable branch prediction */
	SCB->CCR |= (1 <<18);
	__DSB();

	/* Enable I-Cache */
	SCB_EnableICache();

	/* Invalidate I-Cache */
	SCB_InvalidateDCache();
	
	/* Enable D-Cache */
	SCB_EnableDCache();
#endif
	
	/* Enable Power Control clock */
	__HAL_RCC_PWR_CLK_ENABLE();

#if !defined(STM32F0xx)
	/* Set voltage scaling */
	__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
#endif
	
	/* Enable HSE Oscillator and activate PLL with HSE as source */
	RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE;
	
	/* Select proper PLL input clock */
	if (RCC_OSCILLATORTYPE == RCC_OSCILLATORTYPE_HSE) {	
		RCC_OscInitStruct.HSEState = RCC_HSE_ON;
		RCC_OscInitStruct.HSIState = RCC_HSI_OFF;
		RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
#if defined(STM32F0xx)
		RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1;
		RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL6;
#endif
	} else {
		RCC_OscInitStruct.HSEState = RCC_HSE_OFF;
		RCC_OscInitStruct.HSIState = RCC_HSI_ON;
		RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
#if defined(STM32F0xx)
		RCC_OscInitStruct.PLL.PREDIV = RCC_PREDIV_DIV1;
		RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL6;
#endif
	}
	
	/* Set PLL parameters */
	RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
	
#if !defined(STM32F0xx)
	RCC_OscInitStruct.PLL.PLLM = RCC_PLLM;
	RCC_OscInitStruct.PLL.PLLN = RCC_PLLN;
	RCC_OscInitStruct.PLL.PLLP = RCC_PLLP;
	RCC_OscInitStruct.PLL.PLLQ = RCC_PLLQ;
#endif
	
#if defined(STM32F446xx)
#if defined(RCC_PLLR)
	RCC_OscInitStruct.PLL.PLLR = RCC_PLLR;
#else
	RCC_OscInitStruct.PLL.PLLR = 7;
#endif
#endif
	
	/* Try to init */
	if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
		return TM_RCC_Result_Error;
	}

#if defined(STM32F427xx) ||

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ HAL_READ_UINT16函数代码示例发布时间：2022-05-30

C++ HAL_RCC_GetPCLK2Freq函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：18268|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9677|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8177|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8548|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8457|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9388|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8427|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7862|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8411|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7394|2022-11-06

客服电话

电子邮件

C++ HAL_RCC_OscConfig函数代码示例

示例1: SystemClock_Config

示例2: SystemClock_Config

示例3: SystemClock_Config

示例4: SystemClock_Config

示例5: SystemClock_Config

示例6: PLL

示例7: SystemClock_Config

示例8: HAL_RTC_MspInit

示例9: rtc_free

示例10: SetSysClock

示例11: SystemClock_Config

示例12: SystemClock_Config

示例13: PLL

示例14: HAL_RTC_MspInit

示例15: SystemClock_Config

示例16: SystemClockHSE_Config

示例17: __attribute__

示例18: SystemClock_Config

示例19: TM_RCC_InitSystem

请发表评论

全部评论

上一篇：

下一篇：

bradtraversy/iweather: Ionic 3 mobile we

joaomh/curso-de-matlab

断牙刷新位置时间（断牙属性及刷新位置介绍

CVE-2022-34114

rugk/mastodon-simplified-federation: Sim

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053

示例17: attribute