C++ HAL_UART_DeInit函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中HAL_UART_DeInit函数的典型用法代码示例。如果您正苦于以下问题：C++ HAL_UART_DeInit函数的具体用法？C++ HAL_UART_DeInit怎么用？C++ HAL_UART_DeInit使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了HAL_UART_DeInit函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: USBD_CDC_DeInit

static uint8_t USBD_CDC_DeInit (USBD_HandleTypeDef *pdev, uint8_t cfgidx)
{
  USBD_CDC_HandleTypeDef *hcdc = context;
  unsigned index;

  for (index = 0; index < NUM_OF_CDC_UARTS; index++,hcdc++)
  {
    /* Close EP IN */
    USBD_LL_CloseEP(pdev, parameters[index].data_in_ep);
  
    /* Close EP OUT */
    USBD_LL_CloseEP(pdev, parameters[index].data_out_ep);
  
    /* Close Command IN EP */
    USBD_LL_CloseEP(pdev, parameters[index].command_ep);

    /* DeInitialize the UART peripheral */
    if (hcdc->UartHandle.Instance)
      if(HAL_UART_DeInit(&hcdc->UartHandle) != HAL_OK)
      {
        /* Initialization Error */
        Error_Handler();
      }
  }
  
  return USBD_OK;
}

开发者ID:majbthrd，项目名称:stm32cdcuart，代码行数:27，代码来源:usbd_cdc.c

示例2: _uart_close

/*#####################################################*/
bool _uart_close(Uart_t *UartSettings)
{
	HAL_UART_DeInit((UART_HandleTypeDef*)UartSettings->udata);
	if(UartSettings->udata)
		free(UartSettings->udata);
	return true;
}

开发者ID:MorgothCreator，项目名称:mSdk，代码行数:8，代码来源:uart_interface.c

示例3: uart_deinit

void uart_deinit(pyb_uart_obj_t *uart_obj) {
    uart_obj->is_enabled = false;
    UART_HandleTypeDef *uart = &uart_obj->uart;
    HAL_UART_DeInit(uart);
    if (uart->Instance == USART1) {
        __USART1_FORCE_RESET();
        __USART1_RELEASE_RESET();
        __USART1_CLK_DISABLE();
    } else if (uart->Instance == USART2) {
        __USART2_FORCE_RESET();
        __USART2_RELEASE_RESET();
        __USART2_CLK_DISABLE();
    } else if (uart->Instance == USART3) {
        __USART3_FORCE_RESET();
        __USART3_RELEASE_RESET();
        __USART3_CLK_DISABLE();
    } else if (uart->Instance == UART4) {
        __UART4_FORCE_RESET();
        __UART4_RELEASE_RESET();
        __UART4_CLK_DISABLE();
    } else if (uart->Instance == USART6) {
        __USART6_FORCE_RESET();
        __USART6_RELEASE_RESET();
        __USART6_CLK_DISABLE();
    }
}

开发者ID:JMassapina，项目名称:micropython，代码行数:26，代码来源:uart.c

示例4: SleepMode

void SleepMode(void)
{
  GPIO_InitTypeDef GPIO_InitStruct;

  /* Disable all GPIOs to reduce power */
  MX_GPIO_Deinit();

  /* Configure User push-button as external interrupt generator */
  __HAL_RCC_GPIOC_CLK_ENABLE();
  GPIO_InitStruct.Pin = B1_Pin;
  GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  HAL_GPIO_Init(B1_GPIO_Port, &GPIO_InitStruct);

  HAL_UART_DeInit(&huart2);

  /* Suspend Tick increment to prevent wakeup by Systick interrupt.
     Otherwise the Systick interrupt will wake up the device within 1ms (HAL time base) */
  HAL_SuspendTick();

  __HAL_RCC_PWR_CLK_ENABLE();
  /* Request to enter SLEEP mode */
  HAL_PWR_EnterSLEEPMode(0, PWR_SLEEPENTRY_WFI);

  /* Resume Tick interrupt if disabled prior to sleep mode entry*/
  HAL_ResumeTick();

  /* Reinitialize GPIOs */
  MX_GPIO_Init();

  /* Reinitialize UART2 */
  MX_USART2_UART_Init();
}

开发者ID:Shreeyak，项目名称:mastering-stm32，代码行数:33，代码来源:main-ex1.c

示例5: CDC_Itf_DeInit

/**
  * @brief  CDC_Itf_DeInit
  *         DeInitializes the CDC media low layer
  * @param  None
  * @retval Result of the operation: USBD_OK if all operations are OK else USBD_FAIL
  */
static int8_t CDC_Itf_DeInit(void)
{
  /* DeInitialize the UART peripheral */
  if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }
  return (USBD_OK);
}

开发者ID:Lembed，项目名称:STM32CubeF1-mirrors，代码行数:16，代码来源:usbd_cdc_interface.c

示例6: Debug_UARTConfig

void Debug_UARTConfig() { 
    UARTHandle.Instance = USART2;
    UARTHandle.Init.BaudRate = UART_BAUDRATE;
    UARTHandle.Init.WordLength = UART_WORDLENGTH_8B;
    UARTHandle.Init.StopBits = UART_STOPBITS_1;
    UARTHandle.Init.Parity = UART_PARITY_NONE;
    UARTHandle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
    UARTHandle.Init.Mode = UART_MODE_TX_RX;
    UARTHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;

    HAL_UART_DeInit(&UARTHandle);
    HAL_UART_Init(&UARTHandle);
}

开发者ID:RyanSamlalsingh，项目名称:UART-Debug-Library，代码行数:13，代码来源:uart_debug.c

示例7: prvDisableRs232Interface

/**
 * @brief	Disables the RS232 interface
 * @param	None
 * @retval	None
 */
static void prvDisableRs232Interface()
{
	HAL_NVIC_DisableIRQ(UART4_IRQn);
	HAL_UART_DeInit(&UART_Handle);
	__UART4_CLK_DISABLE();
	xSemaphoreGive(xSemaphore);

	prvRxBuffer1CurrentIndex = 0;
	prvRxBuffer1Count = 0;
	prvRxBuffer1State = BUFFERState_Writing;
	prvRxBuffer2CurrentIndex = 0;
	prvRxBuffer2Count = 0;
	prvRxBuffer2State = BUFFERState_Writing;
}

开发者ID:efimefimefim，项目名称:HexConnect，代码行数:19，代码来源:rs232_task.c

示例8: HAL_UART_DeInit

void HardwareSerial::begin(uint32_t baud) {

	HAL_StatusTypeDef status;
	if ( huart6.Init.BaudRate != baud ) {
		HAL_UART_DeInit(&huart6);
		huart6.Init.BaudRate = baud;
		HAL_UART_Init(&huart6);
	}
	this->tx_in_progress = false;
	this->rx_buffer_bytes_available = 0;
	this->rx_buffer_index = 0;
	receive_request_pending = false;
	status = HAL_UART_Receive_IT(&huart6, &this->rx_buffer[this->rx_buffer_index], 1);

}

开发者ID:FRC1640，项目名称:2015-Code，代码行数:15，代码来源:HardwareSerial.cpp

示例9: prvDisableUart1Interface

/**
 * @brief	Disables the UART1 interface
 * @param	None
 * @retval	None
 */
static void prvDisableUart1Interface()
{
	HAL_NVIC_DisableIRQ(USART1_IRQn);
	HAL_UART_DeInit(&UART_Handle);
	__USART1_CLK_DISABLE();
	xSemaphoreGive(xSemaphore);

	prvRxBuffer1CurrentIndex = 0;
	prvRxBuffer1Count = 0;
	prvRxBuffer1State = BUFFERState_Writing;
	prvRxBuffer2CurrentIndex = 0;
	prvRxBuffer2Count = 0;
	prvRxBuffer2State = BUFFERState_Writing;

	prvChannelIsEnabled = false;
}

开发者ID:efimefimefim，项目名称:HexConnect，代码行数:21，代码来源:uart1_task.c

示例10: PX4FlowPortInit

 void PX4FlowPortInit(void)
 {
	 //*******************************************************
	 //配置USART发送与接受
		__USART1_CLK_ENABLE();
		PX4_UartHandle.Instance        = USART1;

		PX4_UartHandle.Init.BaudRate   = 115200;
		PX4_UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
		PX4_UartHandle.Init.StopBits   = UART_STOPBITS_1;
		PX4_UartHandle.Init.Parity     = UART_PARITY_NONE;
		PX4_UartHandle.Init.HwFlowCtl  = UART_HWCONTROL_NONE;
		PX4_UartHandle.Init.Mode       = UART_MODE_TX_RX;
		PX4_UartHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_RXOVERRUNDISABLE_INIT; 
		PX4_UartHandle.AdvancedInit.OverrunDisable=UART_ADVFEATURE_OVERRUN_DISABLE;//关闭OverRun
		HAL_UART_DeInit(&PX4_UartHandle);//卸载USART1
		HAL_UART_Init(&PX4_UartHandle);//装载USART1
	 		   /* NVIC for USART, to catch the RX complete */
  
  /*##-4- Put UART peripheral in reception process ###########################*/ 
    /* Enable the UART Data Register not empty Interrupt */
    __HAL_UART_ENABLE_IT(&PX4_UartHandle, UART_IT_RXNE);	
 }

开发者ID:authuir，项目名称:Aircraft，代码行数:23，代码来源:px4.c

示例11: uart_init_peripheral

static int uart_init_peripheral(void)
{
  __HAL_RCC_USART2_CLK_ENABLE();
  __HAL_RCC_DMA1_CLK_ENABLE();

  UARThandle.Instance                   = UART_INSTANCE;
  UARThandle.Init.BaudRate              = UART_BAUDRATE;
  UARThandle.Init.WordLength            = UART_WORDLENGTH_8B;
  UARThandle.Init.StopBits              = UART_STOPBITS_1;
  UARThandle.Init.Parity                = UART_PARITY_NONE;
  UARThandle.Init.HwFlowCtl             = UART_HWCONTROL_NONE;
  UARThandle.Init.OverSampling          = UART_OVERSAMPLING_8;
  UARThandle.Init.Mode                  = UART_MODE_TX_RX;

  DMAhandle_TX.Instance                 = DMA1_Stream6;
  DMAhandle_TX.Init.Channel             = DMA_CHANNEL_4;
  DMAhandle_TX.Init.Direction           = DMA_MEMORY_TO_PERIPH;
  DMAhandle_TX.Init.FIFOMode            = DMA_FIFOMODE_DISABLE;
  DMAhandle_TX.Init.MemBurst            = DMA_MBURST_SINGLE;
  DMAhandle_TX.Init.MemDataAlignment    = DMA_MDATAALIGN_BYTE;
  DMAhandle_TX.Init.MemInc              = DMA_MINC_ENABLE;
  DMAhandle_TX.Init.Mode                = DMA_NORMAL;
  DMAhandle_TX.Init.PeriphBurst         = DMA_PBURST_SINGLE;
  DMAhandle_TX.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
  DMAhandle_TX.Init.PeriphInc           = DMA_PINC_DISABLE;
  DMAhandle_TX.Init.Priority            = DMA_PRIORITY_LOW;

  DMAhandle_RX                          = DMAhandle_TX;
  DMAhandle_RX.Instance                 = DMA1_Stream5;
  DMAhandle_RX.Init.Channel             = DMA_CHANNEL_4;
  DMAhandle_RX.Init.Direction           = DMA_PERIPH_TO_MEMORY;
  DMAhandle_RX.Init.Mode                = DMA_CIRCULAR;

  UARThandle.hdmatx = &DMAhandle_TX;
  UARThandle.hdmarx = &DMAhandle_RX;
  HAL_UART_DeInit(&UARThandle);
  HAL_UART_Init(&UARThandle);

  UART_INSTANCE->BRR = (2u << 4u) | (5u); /* Baudrate = 2000000 with SYSCLK=168MHz,
                                           * HAL is not very good at figuring this number out... */

  HAL_DMA_DeInit(&DMAhandle_TX);
  HAL_DMA_Init(&DMAhandle_TX);
  HAL_DMA_DeInit(&DMAhandle_RX);
  HAL_DMA_Init(&DMAhandle_RX);

  NVIC_SetPriority(DMA1_Stream6_IRQn, UART_DMA_TX_IRQ_PRIO);
  HAL_NVIC_EnableIRQ(DMA1_Stream6_IRQn);
  NVIC_SetPriority(DMA1_Stream5_IRQn, UART_DMA_RX_IRQ_PRIO);
  HAL_NVIC_EnableIRQ(DMA1_Stream5_IRQn);

  /* Use uart data register as peripheral destination for TX */
  DMAhandle_TX.Instance->PAR = (uint32_t) &(UARThandle.Instance->DR);

  /* Set source and destination address and buffer length */
  DMAhandle_RX.Instance->NDTR = RX_BUF_LEN;
  DMAhandle_RX.Instance->PAR  = (uint32_t) &(UARThandle.Instance->DR);
  DMAhandle_RX.Instance->M0AR = (uint32_t) dma_buffer_rx;

  /* Enable UART as DMA enabled receiver */
  UARThandle.Instance->CR3 |= USART_CR3_DMAR;

  /* Enable transfer complete interrupt */
  __HAL_DMA_ENABLE_IT(&DMAhandle_RX, DMA_IT_TC);

  __HAL_DMA_ENABLE(&DMAhandle_RX);

  return 0;
}

开发者ID:osannolik，项目名称:calmeas，代码行数:69，代码来源:uart.c

示例12: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
#ifndef BOARD_IN_STOP_MODE
  GPIO_InitTypeDef  GPIO_InitStruct;
#endif
  /* STM32F0xx HAL library initialization:
       - Configure the Flash prefetch
       - Systick timer is configured by default as source of time base, but user 
             can eventually implement his proper time base source (a general purpose 
             timer for example or other time source), keeping in mind that Time base 
             duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
             handled in milliseconds basis.
       - Low Level Initialization
     */
  HAL_Init();

  /* Configure the system clock to 48 MHz */
  SystemClock_Config();
  
  /* Configure LED3 */
  BSP_LED_Init(LED3);



#ifdef BOARD_IN_STOP_MODE  
  /* HSI must be UART clock source to be able to wake up the MCU */
  __HAL_RCC_USART1_CONFIG(RCC_USART1CLKSOURCE_HSI);
#endif
  
  /*##-1- Configure the UART peripheral ######################################*/
  /* Put the USART peripheral in the Asynchronous mode (UART Mode) */
  /* UART configured as follows:
      - Word Length = 8 Bits
      - Stop Bit = One Stop bit
      - Parity = None
      - BaudRate = 9600 baud
      - Hardware flow control disabled (RTS and CTS signals) */
   
  UartHandle.Instance        = USARTx;
  HAL_UART_DeInit(&UartHandle); 

  UartHandle.Init.BaudRate   = 9600;
  UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
  UartHandle.Init.StopBits   = UART_STOPBITS_1;
  UartHandle.Init.Parity     = UART_PARITY_NONE;
  UartHandle.Init.HwFlowCtl  = UART_HWCONTROL_NONE;
  UartHandle.Init.Mode       = UART_MODE_TX_RX;
  UartHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
  
  
  if(HAL_UART_Init(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }
  
#ifdef BOARD_IN_STOP_MODE
  
    BSP_LED_On(LED3);
    /* wait for two seconds before test start */
    HAL_Delay(2000);
  
   /* make sure that no UART transfer is on-going */ 
   while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_BUSY) == SET);
   /* make sure that UART is ready to receive
   * (test carried out again later in HAL_UARTEx_StopModeWakeUpSourceConfig) */   
   while(__HAL_UART_GET_FLAG(&UartHandle, USART_ISR_REACK) == RESET);

  /* set the wake-up event:
   * specify wake-up on RXNE flag */
  WakeUpSelection.WakeUpEvent = UART_WAKEUP_ON_READDATA_NONEMPTY;
  if (HAL_UARTEx_StopModeWakeUpSourceConfig(&UartHandle, WakeUpSelection)!= HAL_OK)
  {
    Error_Handler(); 
  }
 
  /* Enable the UART Wake UP from stop mode Interrupt */
  __HAL_UART_ENABLE_IT(&UartHandle, UART_IT_WUF);
  
  /* about to enter stop mode: switch off LED */
  BSP_LED_Off(LED3);
  /* enable MCU wake-up by UART */
  HAL_UARTEx_EnableStopMode(&UartHandle); 
  /* enter stop mode */
  HAL_PWR_EnterSTOPMode(PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI);

  /* ... STOP mode ... */  
  
  
  SystemClock_Config_fromSTOP();
  /* at that point, MCU has been awoken: the LED has been turned back on */
  /* Wake Up based on RXNE flag successful */ 
  HAL_UARTEx_DisableStopMode(&UartHandle);

  /* wait for some delay */
  HAL_Delay(100);
//.........这里部分代码省略.........

开发者ID:NjordCZ，项目名称:stm32cubef0，代码行数:101，代码来源:main.c

示例13: stm32_configure

static rt_err_t stm32_configure(struct rt_serial_device *serial, struct serial_configure *cfg)
{
    struct stm32_uart *uart;

    RT_ASSERT(serial != RT_NULL);
    RT_ASSERT(cfg != RT_NULL);

    uart = (struct stm32_uart *)serial->parent.user_data;

    uart->UartHandle.Init.BaudRate   = cfg->baud_rate;
    uart->UartHandle.Init.HwFlowCtl  = UART_HWCONTROL_NONE;
    uart->UartHandle.Init.Mode       = UART_MODE_TX_RX;
    uart->UartHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;

    switch (cfg->data_bits)
    {
    case DATA_BITS_7:
        uart->UartHandle.Init.WordLength = UART_WORDLENGTH_7B;
        break;
    case DATA_BITS_8:
        uart->UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
        break;
    case DATA_BITS_9:
        uart->UartHandle.Init.WordLength = UART_WORDLENGTH_9B;
        break;
    default:
        uart->UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
        break;
    }
    switch (cfg->stop_bits)
    {
    case STOP_BITS_1:
        uart->UartHandle.Init.StopBits   = UART_STOPBITS_1;
        break;
    case STOP_BITS_2:
        uart->UartHandle.Init.StopBits   = UART_STOPBITS_2;
        break;
    default:
        uart->UartHandle.Init.StopBits   = UART_STOPBITS_1;
        break;
    }
    switch (cfg->parity)
    {
    case PARITY_NONE:
        uart->UartHandle.Init.Parity     = UART_PARITY_NONE;
        break;
    case PARITY_ODD:
        uart->UartHandle.Init.Parity     = UART_PARITY_ODD;
        break;
    case PARITY_EVEN:
        uart->UartHandle.Init.Parity     = UART_PARITY_EVEN;
        break;
    default:
        uart->UartHandle.Init.Parity     = UART_PARITY_NONE;
        break;
    }
    if (HAL_UART_DeInit(&uart->UartHandle) != HAL_OK)
    {
        return RT_ERROR;
    }
    if (HAL_UART_Init(&uart->UartHandle) != HAL_OK)
    {
        return RT_ERROR;
    }

    return RT_EOK;
}

开发者ID:heyuanjie87，项目名称:rt-thread，代码行数:67，代码来源:drv_usart.c

示例14: HELPER_UART_DeInit

/**
 * @brief	Uart De-Initialization Function.
 * @param	numUart: numero della periferica UART da de-inizializzare.
 * 			numUart può assumere uno dei seguenti valori:
 * 			@arg HELPER_UART1: periferica UART 1;
 * 			@arg HELPER_UART2: periferica UART 2.
 * 			@arg HELPER_UART3: periferica UART 3;
 * 			@arg HELPER_UART4: periferica UART 4.
 * 			@arg HELPER_UART5: periferica UART 5;
 * 			@arg HELPER_UART6: periferica UART 6.
 *
 * @retval	None
 */
HAL_StatusTypeDef HELPER_UART_DeInit(HELPER_UART_TypeDef numUart){
	return HAL_UART_DeInit(HELPER_UART_GetHandle(numUart));
}

开发者ID:ntonjeta，项目名称:Nodo-Sensore，代码行数:16，代码来源:stm32f4xx_uart_helper.c

示例15: uartReconfigure

void uartReconfigure(uartPort_t *uartPort)
{
    /*RCC_PeriphCLKInitTypeDef RCC_PeriphClkInit;
    RCC_PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART1|RCC_PERIPHCLK_USART2|RCC_PERIPHCLK_USART3|
            RCC_PERIPHCLK_UART4|RCC_PERIPHCLK_UART5|RCC_PERIPHCLK_USART6|RCC_PERIPHCLK_UART7|RCC_PERIPHCLK_UART8;
    RCC_PeriphClkInit.Usart1ClockSelection = RCC_USART1CLKSOURCE_SYSCLK;
    RCC_PeriphClkInit.Usart2ClockSelection = RCC_USART2CLKSOURCE_SYSCLK;
    RCC_PeriphClkInit.Usart3ClockSelection = RCC_USART3CLKSOURCE_SYSCLK;
    RCC_PeriphClkInit.Uart4ClockSelection = RCC_UART4CLKSOURCE_SYSCLK;
    RCC_PeriphClkInit.Uart5ClockSelection = RCC_UART5CLKSOURCE_SYSCLK;
    RCC_PeriphClkInit.Usart6ClockSelection = RCC_USART6CLKSOURCE_SYSCLK;
    RCC_PeriphClkInit.Uart7ClockSelection = RCC_UART7CLKSOURCE_SYSCLK;
    RCC_PeriphClkInit.Uart8ClockSelection = RCC_UART8CLKSOURCE_SYSCLK;
    HAL_RCCEx_PeriphCLKConfig(&RCC_PeriphClkInit);*/

    HAL_UART_DeInit(&uartPort->Handle);
    uartPort->Handle.Init.BaudRate = uartPort->port.baudRate;
    // according to the stm32 documentation wordlen has to be 9 for parity bits
    // this does not seem to matter for rx but will give bad data on tx!
    uartPort->Handle.Init.WordLength = (uartPort->port.options & SERIAL_PARITY_EVEN) ? UART_WORDLENGTH_9B : UART_WORDLENGTH_8B;
    uartPort->Handle.Init.StopBits = (uartPort->port.options & SERIAL_STOPBITS_2) ? USART_STOPBITS_2 : USART_STOPBITS_1;
    uartPort->Handle.Init.Parity = (uartPort->port.options & SERIAL_PARITY_EVEN) ? USART_PARITY_EVEN : USART_PARITY_NONE;
    uartPort->Handle.Init.HwFlowCtl = UART_HWCONTROL_NONE;
    uartPort->Handle.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
    uartPort->Handle.Init.Mode = 0;

    if (uartPort->port.mode & MODE_RX)
        uartPort->Handle.Init.Mode |= UART_MODE_RX;
    if (uartPort->port.mode & MODE_TX)
        uartPort->Handle.Init.Mode |= UART_MODE_TX;


    usartConfigurePinInversion(uartPort);

#ifdef TARGET_USART_CONFIG
    usartTargetConfigure(uartPort);
#endif

    if (uartPort->port.options & SERIAL_BIDIR)
    {
        HAL_HalfDuplex_Init(&uartPort->Handle);
    }
    else
    {
        HAL_UART_Init(&uartPort->Handle);
    }

    // Receive DMA or IRQ
    if (uartPort->port.mode & MODE_RX)
    {
        if (uartPort->rxDMAStream)
        {
            uartPort->rxDMAHandle.Instance = uartPort->rxDMAStream;
            uartPort->rxDMAHandle.Init.Channel = uartPort->rxDMAChannel;
            uartPort->rxDMAHandle.Init.Direction = DMA_PERIPH_TO_MEMORY;
            uartPort->rxDMAHandle.Init.PeriphInc = DMA_PINC_DISABLE;
            uartPort->rxDMAHandle.Init.MemInc = DMA_MINC_ENABLE;
            uartPort->rxDMAHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
            uartPort->rxDMAHandle.Init.MemDataAlignment = DMA_MDATAALIGN_BYTE;
            uartPort->rxDMAHandle.Init.Mode = DMA_CIRCULAR;
            uartPort->rxDMAHandle.Init.FIFOMode = DMA_FIFOMODE_DISABLE;
            uartPort->rxDMAHandle.Init.FIFOThreshold = DMA_FIFO_THRESHOLD_1QUARTERFULL;
            uartPort->rxDMAHandle.Init.PeriphBurst = DMA_PBURST_SINGLE;
            uartPort->rxDMAHandle.Init.MemBurst = DMA_MBURST_SINGLE;
            uartPort->rxDMAHandle.Init.Priority = DMA_PRIORITY_MEDIUM;


            HAL_DMA_DeInit(&uartPort->rxDMAHandle);
            HAL_DMA_Init(&uartPort->rxDMAHandle);
            /* Associate the initialized DMA handle to the UART handle */
            __HAL_LINKDMA(&uartPort->Handle, hdmarx, uartPort->rxDMAHandle);

            HAL_UART_Receive_DMA(&uartPort->Handle, (uint8_t*)uartPort->port.rxBuffer, uartPort->port.rxBufferSize);

            uartPort->rxDMAPos = __HAL_DMA_GET_COUNTER(&uartPort->rxDMAHandle);

        }
        else
        {
            /* Enable the UART Parity Error Interrupt */
            SET_BIT(uartPort->USARTx->CR1, USART_CR1_PEIE);

            /* Enable the UART Error Interrupt: (Frame error, noise error, overrun error) */
            SET_BIT(uartPort->USARTx->CR3, USART_CR3_EIE);

            /* Enable the UART Data Register not empty Interrupt */
            SET_BIT(uartPort->USARTx->CR1, USART_CR1_RXNEIE);
        }
    }

    // Transmit DMA or IRQ
    if (uartPort->port.mode & MODE_TX) {

        if (uartPort->txDMAStream) {
            uartPort->txDMAHandle.Instance = uartPort->txDMAStream;
            uartPort->txDMAHandle.Init.Channel = uartPort->txDMAChannel;
            uartPort->txDMAHandle.Init.Direction = DMA_MEMORY_TO_PERIPH;
            uartPort->txDMAHandle.Init.PeriphInc = DMA_PINC_DISABLE;
            uartPort->txDMAHandle.Init.MemInc = DMA_MINC_ENABLE;
            uartPort->txDMAHandle.Init.PeriphDataAlignment = DMA_PDATAALIGN_BYTE;
//.........这里部分代码省略.........

开发者ID:rotcehdnih，项目名称:betaflight，代码行数:101，代码来源:serial_uart_hal.c

示例16: armPortClose

int armPortClose(void* port)
{
	UART_HandleTypeDef* huart = (UART_HandleTypeDef*)port;
	HAL_UART_DeInit(&huart);
	return 0;
}

开发者ID:RomualdoGobbo，项目名称:armapi，代码行数:6，代码来源:armport_stm32.c

示例17: source

 /* STM32F3xx HAL library initialization:
       - Configure the Flash prefetch
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Set NVIC Group Priority to 4
       - Low Level Initialization
			 */
void com_DMA()
{

  HAL_Init();
	
	  /* Configure the system clock to 168 Mhz */
  SystemClock_Config();
	  /*##-1- Configure the UART peripheral ######################################*/
  /* Put the USART peripheral in the Asynchronous mode (UART Mode) */
  /* UART configured as follows:
      - Word Length = 8 Bits
      - Stop Bit = One Stop bit
      - Parity = None
      - BaudRate = 9600 baud
      - Hardware flow control disabled (RTS and CTS signals) */

  UartHandle.USART_BaudRate   = 38400;
  UartHandle.USART_WordLength = USART_WordLength_8b;
  UartHandle.USART_StopBits   = USART_StopBits_1;
  UartHandle.USART_Parity     = USART_Parity_No;
  UartHandle.USART_HardwareFlowControl  = USART_HardwareFlowControl_None;
  UartHandle.USART_Mode       = USART_Mode_Rx|USART_Mode_Tx;
  
  if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  } 
  if(HAL_UART_Init(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }
  
#ifdef TRANSMITTER_BOARD

  /* Configure User push-button */
  BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);
  
  /* Wait for User push-button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) == RESET)
  {
  }
  
  /* The board sends the message and expects to receive it back */
  
  /*##-2- Start the transmission process #####################################*/  
  /* While the UART in reception process, user can transmit data through 
     "aTxBuffer" buffer */
  if(HAL_UART_Transmit_DMA(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
  {
    Error_Handler();
  }
  
  /*##-3- Wait for the end of the transfer ###################################*/  
  while (UartReady != SET)
  {
  }
  
  /* Reset transmission flag */
  UartReady = RESET;
  
  /*##-4- Put UART peripheral in reception process ###########################*/  
  if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  } 
  if(HAL_UART_Init(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }  
  if(HAL_UART_Receive_DMA(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
  {
    Error_Handler();
  }

#else
  
  /* The board receives the message and sends it back */

  /*##-2- Put UART peripheral in reception process ###########################*/  
  if(HAL_UART_Receive_DMA(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
  {
    Error_Handler();
  }
  
  /*##-3- Wait for the end of the transfer ###################################*/  
  while (UartReady != SET)
  {
  }

  /* Reset transmission flag */
//.........这里部分代码省略.........

开发者ID:tsymiar，项目名称:4AxisFlying，代码行数:101，代码来源:signal_transmit.c

示例18: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F0xx HAL library initialization:
       - Configure the Flash prefetch
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Low Level Initialization
     */
  HAL_Init();
  
  /* Configure the system clock to 48 MHz */
  SystemClock_Config();

  /* Configure LED3 and LED4 */
  BSP_LED_Init(LED3);
  BSP_LED_Init(LED4);
  /*##-1- Configure the UART peripheral ######################################*/
  /* Put the USART peripheral in the Asynchronous mode (UART Mode) */
  /* UART configured as follows:
      - Word Length = 8 Bits
      - Stop Bit = One Stop bit
      - Parity = None
      - BaudRate = 9600 baud
      - Hardware flow control disabled (RTS and CTS signals) */
  UartHandle.Instance        = USARTx;

  UartHandle.Init.BaudRate   = 9600;
  UartHandle.Init.WordLength = UART_WORDLENGTH_8B;
  UartHandle.Init.StopBits   = UART_STOPBITS_1;
  UartHandle.Init.Parity     = UART_PARITY_NONE;
  UartHandle.Init.HwFlowCtl  = UART_HWCONTROL_NONE;
  UartHandle.Init.Mode       = UART_MODE_TX_RX;
  UartHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
  if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }  
  if(HAL_UART_Init(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }
  
  /*##-1- Configure the I2C peripheral ######################################*/
  I2cHandle.Instance             = I2Cx;
  
  I2cHandle.Init.Timing          = I2C_TIMING;
  I2cHandle.Init.OwnAddress1     = I2C_ADDRESS;
  I2cHandle.Init.AddressingMode  = I2C_ADDRESSINGMODE_7BIT;
  I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
  I2cHandle.Init.OwnAddress2     = 0xFF;
  I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
  I2cHandle.Init.NoStretchMode   = I2C_NOSTRETCH_DISABLE;  
  
  if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();    
  }

  /* Enable the Analog I2C Filter */
  HAL_I2CEx_ConfigAnalogFilter(&I2cHandle,I2C_ANALOGFILTER_ENABLE);

  
  /* Configure User push-button Button*/
  BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);

	do{
		/* Wait for User push-button Button press before starting the Communication */
		while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
		{
		}
		
		/* Wait for User push-button Button release before starting the Communication */
		while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
		{
		}
				
		void ndef_test(void);
		float get_adc(void);
		
		ndef_test();
		//get_adc();
	}while(1);

}

开发者ID:everrin，项目名称:stm32f0_M24LR04E，代码行数:93，代码来源:main.c

示例19: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F4xx HAL library initialization:
       - Configure the Flash prefetch, instruction and Data caches
       - Systick timer is configured by default as source of time base, but user
         can eventually implement his proper time base source (a general purpose
         timer for example or other time source), keeping in mind that Time base
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and
         handled in milliseconds basis.
       - Set NVIC Group Priority to 4
       - Low Level Initialization: global MSP (MCU Support Package) initialization
     */
  HAL_Init();

  /* Configure the system clock to 100 MHz */
  SystemClock_Config();

  /* Configure LED2 */
  BSP_LED_Init(LED2);

  /*##-1- Configure the UART peripheral ######################################*/
  /* Put the USART peripheral in the Asynchronous mode (UART Mode) */
  /* UART configured as follows:
      - Word Length = 8 Bits
      - Stop Bit = One Stop bit
      - Parity = None
      - BaudRate = 9600 baud
      - Hardware flow control disabled (RTS and CTS signals) */
  UartHandle.Instance        = USARTx;

  UartHandle.Init.BaudRate     = 115200;
  UartHandle.Init.WordLength   = UART_WORDLENGTH_8B;
  UartHandle.Init.StopBits     = UART_STOPBITS_1;
  UartHandle.Init.Parity       = UART_PARITY_NONE;
  UartHandle.Init.HwFlowCtl    = UART_HWCONTROL_NONE;
  UartHandle.Init.Mode         = UART_MODE_TX_RX;
  UartHandle.Init.OverSampling = UART_OVERSAMPLING_16;

  if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }
  if(HAL_UART_Init(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }

#ifdef TRANSMITTER_BOARD

  /* Configure User push-button in Interrupt mode */
  BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_EXTI);

  /* Wait for User push-button press before starting the Communication.
     In the meantime, LED2 is blinking */
  while(UserButtonStatus == 0)
  {
      /* Toggle LED2*/
      BSP_LED_Toggle(LED2);
      HAL_Delay(100);
  }

  BSP_LED_Off(LED2);

  /* The board sends the message and expects to receive it back */

  /*##-2- Start the transmission process #####################################*/
  /* While the UART in reception process, user can transmit data through
     "aTxBuffer" buffer */
  if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE, 5000)!= HAL_OK)
  {
    Error_Handler();
  }

  /* Turn LED2 on: Transfer in transmission process is correct */
  BSP_LED_On(LED2);

  /*##-3- Put UART peripheral in reception process ###########################*/
  if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 5000) != HAL_OK)
  {
    Error_Handler();
  }

  /* Turn LED2 on: Transfer in reception process is correct */
  BSP_LED_On(LED2);

#else

  /* The board receives the message and sends it back */

  /*##-2- Put UART peripheral in reception process ###########################*/
  if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 0x1FFFFFF) != HAL_OK)
  {
    Error_Handler();
  }

//.........这里部分代码省略.........

开发者ID:Joe-Merten，项目名称:Stm32-Tools-Evaluation，代码行数:101，代码来源:main.c

示例20: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F3xx HAL library initialization:
       - Configure the Flash prefetch
       - Configure the Systick to generate an interrupt each 1 msec
       - Set NVIC Group Priority to 4
       - Low Level Initialization
     */
  HAL_Init();

  /* Configure the system clock to 64 MHz */
  SystemClock_Config();
  
  /* Configure LED1, LED2 and LED3 */
  BSP_LED_Init(LED1);
  BSP_LED_Init(LED2);
  BSP_LED_Init(LED3);

  /*##-1- Configure the UART peripheral ######################################*/
  /* Put the USART peripheral in the Asynchronous mode (UART Mode) */
  /* UART configured as follows:
      - Word Length = 8 Bits
      - Stop Bit = One Stop bit
      - Parity = None
      - BaudRate = 9600 baud
      - Hardware flow control disabled (RTS and CTS signals) */
  UartHandle.Instance        = USARTx;

  UartHandle.Init.BaudRate     = 9600;
  UartHandle.Init.WordLength   = UART_WORDLENGTH_8B;
  UartHandle.Init.StopBits     = UART_STOPBITS_1;
  UartHandle.Init.Parity       = UART_PARITY_NONE;
  UartHandle.Init.HwFlowCtl    = UART_HWCONTROL_NONE;
  UartHandle.Init.Mode         = UART_MODE_TX_RX;
  UartHandle.Init.OverSampling = UART_OVERSAMPLING_16;
  UartHandle.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;

  if(HAL_UART_DeInit(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }  
  if(HAL_UART_Init(&UartHandle) != HAL_OK)
  {
    Error_Handler();
  }
  
#ifdef TRANSMITTER_BOARD

  /* Configure User push-button in Interrupt mode */
  BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_EXTI);
  
  /* Wait for User push-button press before starting the Communication.
     In the meantime, LED3 is blinking */
  while(UserButtonStatus == 0)
  {
      /* Toggle LED3*/
      BSP_LED_Toggle(LED3); 
      HAL_Delay(100);
  }
  
  BSP_LED_Off(LED3); 
  /* The board sends the message and expects to receive it back */
  
  /*##-2- Start the transmission process #####################################*/  
  /* While the UART in reception process, user can transmit data through 
     "aTxBuffer" buffer */
  if(HAL_UART_Transmit(&UartHandle, (uint8_t*)aTxBuffer, TXBUFFERSIZE, 5000)!= HAL_OK)
  {
    Error_Handler();   
  }
  
  /* Turn LED1 on: Transfer in transmission process is correct */
  BSP_LED_On(LED1);
  
  /*##-3- Put UART peripheral in reception process ###########################*/  
  if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 5000) != HAL_OK)
  {
    Error_Handler();  
  }
   
 
#else
  
  /* The board receives the message and sends it back */

  /*##-2- Put UART peripheral in reception process ###########################*/
  if(HAL_UART_Receive(&UartHandle, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 0x1FFFFFF) != HAL_OK)
  {
    Error_Handler();
  }
 
  /* Turn LED1 on: Transfer in reception process is correct */
  BSP_LED_On(LED1);
  
  /*##-3- Start the transmission process #####################################*/  
//.........这里部分代码省略.........

开发者ID:PaxInstruments，项目名称:STM32CubeF3，代码行数:101，代码来源:main.c

注：本文中的HAL_UART_DeInit函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ HAL_UART_IRQHandler函数代码示例发布时间：2022-05-30

C++ HAL_TIM_ReadCapturedValue函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：18268|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9677|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8177|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8548|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8457|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9388|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8427|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7862|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8411|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7394|2022-11-06

客服电话

电子邮件

C++ HAL_UART_DeInit函数代码示例

示例1: USBD_CDC_DeInit

示例2: _uart_close

示例3: uart_deinit

示例4: SleepMode

示例5: CDC_Itf_DeInit

示例6: Debug_UARTConfig

示例7: prvDisableRs232Interface

示例8: HAL_UART_DeInit

示例9: prvDisableUart1Interface

示例10: PX4FlowPortInit

示例11: uart_init_peripheral

示例12: main

示例13: stm32_configure

示例14: HELPER_UART_DeInit

示例15: uartReconfigure

示例16: armPortClose

示例17: source

示例18: main

示例19: main

示例20: main

请发表评论

全部评论

上一篇：

下一篇：

bradtraversy/iweather: Ionic 3 mobile we

joaomh/curso-de-matlab

断牙刷新位置时间（断牙属性及刷新位置介绍

CVE-2022-34114

rugk/mastodon-simplified-federation: Sim

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053