static int __init hs_probe(struct platform_device *pdev)
{
	int result = 0;
	mic.hsmajor = 0;
	mic.headset_state = 0;
	mic.hsbtime.tv.sec = 0;
	mic.hsbtime.tv.nsec = 0;
	mic.headset_pd = NULL;
	mic.check_count = 0;

#ifdef CONFIG_SWITCH
	result = hs_switchinit(&mic);
	if (result < 0)
		return result;
#endif

	result = hs_inputdev(&mic);
	if (result < 0)
		goto err;

	result = register_chrdev(mic.hsmajor, "BrcmHeadset", &hs_fops);
	if(result < 0)
		goto err1;
	else if(result > 0 && (mic.hsmajor == 0))    /* this is for dynamic major */
		mic.hsmajor = result;

	wake_lock_init(&mic.det_wake_lock, WAKE_LOCK_SUSPEND, "sec_jack_det");
	INIT_DELAYED_WORK(&(mic.imsi_work), getIMSI_work_func);

	/* check if platform data is defined for a particular board variant */
	if (pdev->dev.platform_data)
	{
		mic.headset_pd = pdev->dev.platform_data;

		KEY_PRESS_THRESHOLD = mic.headset_pd->key_press_threshold;
		KEY_3POLE_THRESHOLD = mic.headset_pd->key_3pole_threshold;
		KEY1_THRESHOLD_L = mic.headset_pd->key1_threshold_l;
		KEY1_THRESHOLD_U = mic.headset_pd->key1_threshold_u;
		KEY2_THRESHOLD_L = mic.headset_pd->key2_threshold_l;
		KEY2_THRESHOLD_U = mic.headset_pd->key2_threshold_u;
		KEY3_THRESHOLD_L = mic.headset_pd->key3_threshold_l;
		KEY3_THRESHOLD_U = mic.headset_pd->key3_threshold_u;

		if (mic.headset_pd->hsgpio == 0)
			mic.hsirq = mic.headset_pd->hsirq;
		else
		{
			setup_timer(&mic.timer, gpio_jack_timer, (unsigned long)&mic); // timer register. 

			if (gpio_request(mic.headset_pd->hsgpio, "headset detect") < 0)
			{
				printk("%s: Could not reserve headset signal GPIO!\n", __func__);
				goto err2;
			}
			gpio_direction_input(mic.headset_pd->hsgpio);
			bcm_gpio_set_db_val(mic.headset_pd->hsgpio, 0x7);
			mic.hsirq = gpio_to_irq(mic.headset_pd->hsgpio);
		}
		mic.hsbirq = mic.headset_pd->hsbirq;
	}
	else
	{
		mic.hsirq = platform_get_irq(pdev, 0);
		mic.hsbirq = platform_get_irq(pdev, 1);
	}

	printk("%s: HS irq %d\n", __func__, mic.hsirq);
	printk("%s: HSB irq %d\n", __func__, mic.hsbirq);
	result = request_irq(mic.hsbirq, hs_buttonisr,  IRQF_NO_SUSPEND, "BrcmHeadsetButton",  (void *) NULL);
	mic.hsbst = DISABLE;

	if(result < 0)
		goto err2;

	result = request_irq(mic.hsirq, hs_isr,(IRQF_DISABLED | IRQF_TRIGGER_RISING|IRQF_TRIGGER_FALLING | IRQF_NO_SUSPEND), "BrcmHeadset",  &mic);
	if(result < 0)
	{
		free_irq(mic.hsbirq, &mic);
		goto err2;
	}

	printk("%s: BrcmHeadset: module inserted >>>> . Major number is = %d\n", __func__, mic.hsmajor);

	/* Set the ANACR2 bit for mic power down */
	board_sysconfig(SYSCFG_AUXMIC, SYSCFG_INIT);
	board_sysconfig(SYSCFG_HEADSET, SYSCFG_INIT);

	/*Fix the audio path is wrong when headset already plugged in the device  then boot device case.*/
	if (mic.headset_pd->hsgpio != 0)
	{
		mic.headset_pd->check_hs_state(&mic.headset_state);
		printk("%s: headset_state:%d\n", __func__, mic.headset_state); 
		set_irq_type(mic.hsirq, (mic.headset_state) ? IRQF_TRIGGER_RISING : IRQF_TRIGGER_FALLING);
		schedule_work(&(mic.switch_data.work));
		schedule_delayed_work(&(mic.imsi_work), GET_IMSI_REF_TIME);
	}

	return 0;

err2:   unregister_chrdev(mic.hsmajor,"BrcmHeadset");
//.........这里部分代码省略.........

/*
 * vpif_probe: This function creates device entries by register itself to the
 * V4L2 driver and initializes fields of each channel objects
 */
static __init int vpif_probe(struct platform_device *pdev)
{
	struct vpif_subdev_info *subdevdata;
	struct vpif_display_config *config;
	int i, j = 0, k, q, m, err = 0;
	struct i2c_adapter *i2c_adap;
	struct common_obj *common;
	struct channel_obj *ch;
	struct video_device *vfd;
	struct resource *res;
	int subdev_count;

	vpif_dev = &pdev->dev;

	err = initialize_vpif();

	if (err) {
		v4l2_err(vpif_dev->driver, "Error initializing vpif\n");
		return err;
	}

	err = v4l2_device_register(vpif_dev, &vpif_obj.v4l2_dev);
	if (err) {
		v4l2_err(vpif_dev->driver, "Error registering v4l2 device\n");
		return err;
	}

	k = 0;
	while ((res = platform_get_resource(pdev, IORESOURCE_IRQ, k))) {
		for (i = res->start; i <= res->end; i++) {
			if (request_irq(i, vpif_channel_isr, IRQF_DISABLED,
					"DM646x_Display",
				(void *)(&vpif_obj.dev[k]->channel_id))) {
				err = -EBUSY;
				goto vpif_int_err;
			}
		}
		k++;
	}

	for (i = 0; i < VPIF_DISPLAY_MAX_DEVICES; i++) {

		/* Get the pointer to the channel object */
		ch = vpif_obj.dev[i];

		/* Allocate memory for video device */
		vfd = video_device_alloc();
		if (vfd == NULL) {
			for (j = 0; j < i; j++) {
				ch = vpif_obj.dev[j];
				video_device_release(ch->video_dev);
			}
			err = -ENOMEM;
			goto vpif_int_err;
		}

		/* Initialize field of video device */
		*vfd = vpif_video_template;
		vfd->v4l2_dev = &vpif_obj.v4l2_dev;
		vfd->release = video_device_release;
		snprintf(vfd->name, sizeof(vfd->name),
			 "DM646x_VPIFDisplay_DRIVER_V%d.%d.%d",
			 (VPIF_DISPLAY_VERSION_CODE >> 16) & 0xff,
			 (VPIF_DISPLAY_VERSION_CODE >> 8) & 0xff,
			 (VPIF_DISPLAY_VERSION_CODE) & 0xff);

		/* Set video_dev to the video device */
		ch->video_dev = vfd;
	}

	for (j = 0; j < VPIF_DISPLAY_MAX_DEVICES; j++) {
		ch = vpif_obj.dev[j];
		/* Initialize field of the channel objects */
		atomic_set(&ch->usrs, 0);
		for (k = 0; k < VPIF_NUMOBJECTS; k++) {
			ch->common[k].numbuffers = 0;
			common = &ch->common[k];
			common->io_usrs = 0;
			common->started = 0;
			spin_lock_init(&common->irqlock);
			mutex_init(&common->lock);
			common->numbuffers = 0;
			common->set_addr = NULL;
			common->ytop_off = common->ybtm_off = 0;
			common->ctop_off = common->cbtm_off = 0;
			common->cur_frm = common->next_frm = NULL;
			memset(&common->fmt, 0, sizeof(common->fmt));
			common->numbuffers = config_params.numbuffers[k];

		}
		ch->initialized = 0;
		ch->channel_id = j;
		if (j < 2)
			ch->common[VPIF_VIDEO_INDEX].numbuffers =
			    config_params.numbuffers[ch->channel_id];
		else
//.........这里部分代码省略.........

static int __devinit max14656_probe(struct i2c_client *client, const struct i2c_device_id *id)
{
	struct device_node *dev_node = client->dev.of_node;
	struct max14656_chip *chip;
	int ret = 0;
	int rc = 0;
	
	pr_err("%s:\n", __func__);
	
	chip = kzalloc(sizeof(*chip), GFP_KERNEL);
	if (!chip)
		return -ENOMEM;
/*
	chip->batt_psy = power_supply_get_by_name("battery");
	if (!chip->batt_psy) {
		pr_err("%s : batt_psy is not yet ready\n", __func__);
		ret = -EPROBE_DEFER;
		goto error;
	}
*/
	if (!i2c_check_functionality(client->adapter, I2C_FUNC_SMBUS_BYTE_DATA)) {
		pr_err("%s : i2c_check_functionality fail\n", __func__);
		return -EIO;
	}

	chip->client = client;

	/* need dts parser */	
	if (dev_node) {
		ret = max14656_parse_dt(dev_node, chip);
		if (ret) {
			pr_err("failed to parse dt\n");
			goto error;
		}
	}

#ifdef CONFIG_LGE_PM
	chip->chg_detect_done = 0;
	chip->chg_type = 0;
	chip->dcd_timeout = 0;
#endif

	ret = gpio_request_one(chip->int_gpio, GPIOF_DIR_IN,
			"max14656_int");
	if (ret) {
		pr_err("failed to request int_gpio\n");
		goto error;
	}
	chip->irq = gpio_to_irq(chip->int_gpio);
	pr_debug("int_gpio irq#=%d.\n", chip->irq);
	
	i2c_set_clientdata(client, NULL);

	ret = max14656_hw_init(chip);
	if (ret) {
		pr_err("max14656_hwinit failed.ret=%d\n", ret);
		goto err_hw_init;
	}

	INIT_DELAYED_WORK(&chip->irq_work, max14656_irq_worker);

	if (chip->irq) {
		ret = request_irq(chip->irq, max14656_irq,
				IRQF_TRIGGER_FALLING,
				"max14656_irq", chip);
		if (ret) {
			pr_err("request_irq %d failed\n", chip->irq);
			goto err_req_irq;
		}
		enable_irq_wake(chip->irq);
	}

	schedule_delayed_work(&chip->irq_work, msecs_to_jiffies(2000));

#ifdef CONFIG_LGE_PM
	chip->detect_psy = max14656_ps;

	rc = power_supply_register(&chip->client->dev, &chip->detect_psy);
	if (rc < 0) {
			pr_err("[2222]batt failed to register rc = %d\n", rc);
	}
#endif

	pr_info("%s : Done\n", __func__);
	return 0;

err_req_irq:
err_hw_init:
	if (chip->int_gpio)
		gpio_free(chip->int_gpio);
error:
	kfree(chip);
	chip = NULL;
	pr_info("fail to probe\n");
	return ret;
}

int msm_camio_enable(struct platform_device *pdev)
{
	int rc = 0;
	struct msm_camera_sensor_info *sinfo = pdev->dev.platform_data;
	struct msm_camera_device_platform_data *camdev = sinfo->pdata;

	camio_dev = pdev;
	camio_ext = camdev->ioext;
	camio_clk = camdev->ioclk;

	camdev->camera_gpio_on();
	msm_camera_vreg_enable();

	msm_camio_clk_enable(CAMIO_CAM_MCLK_CLK);
	msm_camio_clk_enable(CAMIO_VFE_CLK);
	msm_camio_clk_enable(CAMIO_CSI0_VFE_CLK);
	msm_camio_clk_enable(CAMIO_CSI1_VFE_CLK);
	msm_camio_clk_enable(CAMIO_CSI_SRC_CLK);
	msm_camio_clk_enable(CAMIO_CSI0_CLK);
	msm_camio_clk_enable(CAMIO_CSI1_CLK);
	msm_camio_clk_enable(CAMIO_VFE_PCLK);
	msm_camio_clk_enable(CAMIO_CSI0_PCLK);
	msm_camio_clk_enable(CAMIO_CSI1_PCLK);

	csiio = request_mem_region(camio_ext.csiphy,
		camio_ext.csisz, pdev->name);
	if (!csiio) {
		rc = -EBUSY;
		goto common_fail;
	}
	csibase = ioremap(camio_ext.csiphy,
		camio_ext.csisz);
	if (!csibase) {
		rc = -ENOMEM;
		goto csi_busy;
	}
	rc = request_irq(camio_ext.csiirq, msm_io_csi_irq,
		IRQF_TRIGGER_RISING, "csi", 0);
	if (rc < 0)
		goto csi_irq_fail;

	return 0;

csi_irq_fail:
	iounmap(csibase);
csi_busy:
	release_mem_region(camio_ext.csiphy, camio_ext.csisz);
common_fail:
	msm_camio_clk_disable(CAMIO_CAM_MCLK_CLK);
	msm_camio_clk_disable(CAMIO_CSI0_VFE_CLK);
	msm_camio_clk_disable(CAMIO_CSI0_CLK);
	msm_camio_clk_disable(CAMIO_CSI1_VFE_CLK);
	msm_camio_clk_disable(CAMIO_CSI1_CLK);
	msm_camio_clk_disable(CAMIO_VFE_PCLK);
	msm_camio_clk_disable(CAMIO_CSI0_PCLK);
	msm_camio_clk_disable(CAMIO_CSI1_PCLK);
/* Disable CAMIO_CSI1_VFE_CLK, CAMIO_CSI1_CLK,
	CAMIO_CSI1_PCLK for the secondary sensor */
	msm_camera_vreg_disable();
	camdev->camera_gpio_off();
	return rc;
}

static int __init coh901327_probe(struct platform_device *pdev)
{
	int ret;
	u16 val;
	struct resource *res;

	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	if (!res)
		return -ENOENT;

	parent = &pdev->dev;
	physize = resource_size(res);
	phybase = res->start;

	if (request_mem_region(phybase, physize, DRV_NAME) == NULL) {
		ret = -EBUSY;
		goto out;
	}

	virtbase = ioremap(phybase, physize);
	if (!virtbase) {
		ret = -ENOMEM;
		goto out_no_remap;
	}

	clk = clk_get(&pdev->dev, NULL);
	if (IS_ERR(clk)) {
		ret = PTR_ERR(clk);
		dev_err(&pdev->dev, "could not get clock\n");
		goto out_no_clk;
	}
	ret = clk_enable(clk);
	if (ret) {
		dev_err(&pdev->dev, "could not enable clock\n");
		goto out_no_clk_enable;
	}

	val = readw(virtbase + U300_WDOG_SR);
	switch (val) {
	case U300_WDOG_SR_STATUS_TIMED_OUT:
		dev_info(&pdev->dev,
			"watchdog timed out since last chip reset!\n");
		coh901327_wdt.bootstatus |= WDIOF_CARDRESET;
		
		break;
	case U300_WDOG_SR_STATUS_NORMAL:
		dev_info(&pdev->dev,
			"in normal status, no timeouts have occurred.\n");
		break;
	default:
		dev_info(&pdev->dev,
			"contains an illegal status code (%08x)\n", val);
		break;
	}

	val = readw(virtbase + U300_WDOG_D2R);
	switch (val) {
	case U300_WDOG_D2R_DISABLE_STATUS_DISABLED:
		dev_info(&pdev->dev, "currently disabled.\n");
		break;
	case U300_WDOG_D2R_DISABLE_STATUS_ENABLED:
		dev_info(&pdev->dev,
			 "currently enabled! (disabling it now)\n");
		coh901327_disable();
		break;
	default:
		dev_err(&pdev->dev,
			"contains an illegal enable/disable code (%08x)\n",
			val);
		break;
	}

	
	writew(U300_WDOG_SR_RESET_STATUS_RESET, virtbase + U300_WDOG_SR);

	irq = platform_get_irq(pdev, 0);
	if (request_irq(irq, coh901327_interrupt, 0,
			DRV_NAME " Bark", pdev)) {
		ret = -EIO;
		goto out_no_irq;
	}

	clk_disable(clk);

	if (margin < 1 || margin > 327)
		margin = 60;
	coh901327_wdt.timeout = margin;

	ret = watchdog_register_device(&coh901327_wdt);
	if (ret == 0)
		dev_info(&pdev->dev,
			 "initialized. timer margin=%d sec\n", margin);
	else
		goto out_no_wdog;

	return 0;

out_no_wdog:
	free_irq(irq, pdev);
out_no_irq:
//.........这里部分代码省略.........

static int __devinit ag71xx_probe(struct platform_device *pdev)
{
	struct net_device *dev;
	struct resource *res;
	struct ag71xx *ag;
	struct ag71xx_platform_data *pdata;
	int err;

	pdata = pdev->dev.platform_data;
	if (!pdata) {
		dev_err(&pdev->dev, "no platform data specified\n");
		err = -ENXIO;
		goto err_out;
	}

	if (pdata->mii_bus_dev == NULL) {
		dev_err(&pdev->dev, "no MII bus device specified\n");
		err = -EINVAL;
		goto err_out;
	}

	dev = alloc_etherdev(sizeof(*ag));
	if (!dev) {
		dev_err(&pdev->dev, "alloc_etherdev failed\n");
		err = -ENOMEM;
		goto err_out;
	}

	SET_NETDEV_DEV(dev, &pdev->dev);

	ag = netdev_priv(dev);
	ag->pdev = pdev;
	ag->dev = dev;
	ag->msg_enable = netif_msg_init(ag71xx_msg_level,
					AG71XX_DEFAULT_MSG_ENABLE);
	spin_lock_init(&ag->lock);

	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mac_base");
	if (!res) {
		dev_err(&pdev->dev, "no mac_base resource found\n");
		err = -ENXIO;
		goto err_out;
	}

	ag->mac_base = ioremap_nocache(res->start, res->end - res->start + 1);
	if (!ag->mac_base) {
		dev_err(&pdev->dev, "unable to ioremap mac_base\n");
		err = -ENOMEM;
		goto err_free_dev;
	}

	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mii_ctrl");
	if (!res) {
		dev_err(&pdev->dev, "no mii_ctrl resource found\n");
		err = -ENXIO;
		goto err_unmap_base;
	}

	ag->mii_ctrl = ioremap_nocache(res->start, res->end - res->start + 1);
	if (!ag->mii_ctrl) {
		dev_err(&pdev->dev, "unable to ioremap mii_ctrl\n");
		err = -ENOMEM;
		goto err_unmap_base;
	}

	dev->irq = platform_get_irq(pdev, 0);
	err = request_irq(dev->irq, ag71xx_interrupt,
			  IRQF_DISABLED,
			  dev->name, dev);
	if (err) {
		dev_err(&pdev->dev, "unable to request IRQ %d\n", dev->irq);
		goto err_unmap_mii_ctrl;
	}

	dev->base_addr = (unsigned long)ag->mac_base;
	dev->netdev_ops = &ag71xx_netdev_ops;
	dev->ethtool_ops = &ag71xx_ethtool_ops;

	INIT_WORK(&ag->restart_work, ag71xx_restart_work_func);

	init_timer(&ag->oom_timer);
	ag->oom_timer.data = (unsigned long) dev;
	ag->oom_timer.function = ag71xx_oom_timer_handler;

	memcpy(dev->dev_addr, pdata->mac_addr, ETH_ALEN);

	netif_napi_add(dev, &ag->napi, ag71xx_poll, AG71XX_NAPI_WEIGHT);

	err = register_netdev(dev);
	if (err) {
		dev_err(&pdev->dev, "unable to register net device\n");
		goto err_free_irq;
	}

	printk(KERN_INFO "%s: Atheros AG71xx at 0x%08lx, irq %d\n",
	       dev->name, dev->base_addr, dev->irq);

	ag71xx_dump_regs(ag);

	ag71xx_hw_init(ag);
//.........这里部分代码省略.........

_mali_osk_irq_t *_mali_osk_irq_init( u32 irqnum, _mali_osk_irq_uhandler_t uhandler,	_mali_osk_irq_bhandler_t bhandler, _mali_osk_irq_trigger_t trigger_func, _mali_osk_irq_ack_t ack_func, void *data, const char *description )
{
	mali_osk_irq_object_t *irq_object;

	irq_object = kmalloc(sizeof(mali_osk_irq_object_t), GFP_KERNEL);
	if (NULL == irq_object) return NULL;

#if MALI_LICENSE_IS_GPL
	if (NULL == mali_wq)
	{
#if LINUX_VERSION_CODE >= KERNEL_VERSION(2,6,36)
		mali_wq = alloc_workqueue("mali", WQ_UNBOUND, 0);
#else
		mali_wq = create_workqueue("mali");
#endif
		if(NULL == mali_wq)
		{
			MALI_PRINT_ERROR(("Unable to create Mali workqueue\n"));
			kfree( irq_object );
			return NULL;
		}
	}
#endif

	/* workqueue API changed in 2.6.20, support both versions: */
#if defined(INIT_DELAYED_WORK)
	/* New syntax: INIT_WORK( struct work_struct *work, void (*function)(struct work_struct *)) */
	INIT_WORK( &irq_object->work_queue_irq_handle, irq_handler_bottom_half);
#else
	/* Old syntax: INIT_WORK( struct work_struct *work, void (*function)(void *), void *data) */
	INIT_WORK( &irq_object->work_queue_irq_handle, irq_handler_bottom_half, irq_object);
#endif /* defined(INIT_DELAYED_WORK) */

	if (-1 == irqnum)
	{
		/* Probe for IRQ */
		if ( (NULL != trigger_func) && (NULL != ack_func) )
		{
			unsigned long probe_count = 3;
			_mali_osk_errcode_t err;
			int irq;

			MALI_DEBUG_PRINT(2, ("Probing for irq\n"));

			do
			{
				unsigned long mask;

				mask = probe_irq_on();
				trigger_func(data);

				_mali_osk_time_ubusydelay(5);

				irq = probe_irq_off(mask);
				err = ack_func(data);
			}
			while (irq < 0 && (err == _MALI_OSK_ERR_OK) && probe_count--);

			if (irq < 0 || (_MALI_OSK_ERR_OK != err)) irqnum = -1;
			else irqnum = irq;
		}
		else irqnum = -1; /* no probe functions, fault */

		if (-1 != irqnum)
		{
			/* found an irq */
			MALI_DEBUG_PRINT(2, ("Found irq %d\n", irqnum));
		}
		else
		{
			MALI_DEBUG_PRINT(2, ("Probe for irq failed\n"));
		}
	}
	
	irq_object->irqnum = irqnum;
	irq_object->uhandler = uhandler;
	irq_object->bhandler = bhandler;
	irq_object->data = data;

	/* Is this a real IRQ handler we need? */
	if (!mali_benchmark && irqnum != _MALI_OSK_IRQ_NUMBER_FAKE && irqnum != _MALI_OSK_IRQ_NUMBER_PMM) 
	{
		if (-1 == irqnum)
		{
			MALI_DEBUG_PRINT(2, ("No IRQ for core '%s' found during probe\n", description));
			kfree(irq_object);
			return NULL;
		}

		if (0 != request_irq(irqnum, irq_handler_upper_half, IRQF_SHARED, description, irq_object))
		{
			MALI_DEBUG_PRINT(2, ("Unable to install IRQ handler for core '%s'\n", description));
			kfree(irq_object);
			return NULL;
		}
	}

#if MALI_LICENSE_IS_GPL
	if ( _MALI_OSK_IRQ_NUMBER_PMM == irqnum )
	{
//.........这里部分代码省略.........

static int __devinit ds1553_rtc_probe(struct platform_device *pdev)
{
	struct rtc_device *rtc;
	struct resource *res;
	unsigned int cen, sec;
	struct rtc_plat_data *pdata = NULL;
	void __iomem *ioaddr = NULL;
	int ret = 0;

	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	if (!res)
		return -ENODEV;
	pdata = kzalloc(sizeof(*pdata), GFP_KERNEL);
	if (!pdata)
		return -ENOMEM;
	if (!request_mem_region(res->start, RTC_REG_SIZE, pdev->name)) {
		ret = -EBUSY;
		goto out;
	}
	pdata->baseaddr = res->start;
	ioaddr = ioremap(pdata->baseaddr, RTC_REG_SIZE);
	if (!ioaddr) {
		ret = -ENOMEM;
		goto out;
	}
	pdata->ioaddr = ioaddr;
	pdata->irq = platform_get_irq(pdev, 0);

	/* turn RTC on if it was not on */
	sec = readb(ioaddr + RTC_SECONDS);
	if (sec & RTC_STOP) {
		sec &= RTC_SECONDS_MASK;
		cen = readb(ioaddr + RTC_CENTURY) & RTC_CENTURY_MASK;
		writeb(RTC_WRITE, ioaddr + RTC_CONTROL);
		writeb(sec, ioaddr + RTC_SECONDS);
		writeb(cen & RTC_CENTURY_MASK, ioaddr + RTC_CONTROL);
	}
	if (readb(ioaddr + RTC_FLAGS) & RTC_FLAGS_BLF)
		dev_warn(&pdev->dev, "voltage-low detected.\n");

	if (pdata->irq > 0) {
		writeb(0, ioaddr + RTC_INTERRUPTS);
		if (request_irq(pdata->irq, ds1553_rtc_interrupt,
				IRQF_DISABLED, pdev->name, pdev) < 0) {
			dev_warn(&pdev->dev, "interrupt not available.\n");
			pdata->irq = 0;
		}
	}

	rtc = rtc_device_register(pdev->name, &pdev->dev,
				  &ds1553_rtc_ops, THIS_MODULE);
	if (IS_ERR(rtc)) {
		ret = PTR_ERR(rtc);
		goto out;
	}
	pdata->rtc = rtc;
	pdata->last_jiffies = jiffies;
	platform_set_drvdata(pdev, pdata);
	ret = sysfs_create_bin_file(&pdev->dev.kobj, &ds1553_nvram_attr);
	if (ret)
		goto out;
	return 0;
 out:
	if (pdata->rtc)
		rtc_device_unregister(pdata->rtc);
	if (pdata->irq > 0)
		free_irq(pdata->irq, pdev);
	if (ioaddr)
		iounmap(ioaddr);
	if (pdata->baseaddr)
		release_mem_region(pdata->baseaddr, RTC_REG_SIZE);
	kfree(pdata);
	return ret;
}

static int __devinit pxa930_trkball_probe(struct platform_device *pdev)
{
	struct pxa930_trkball *trkball;
	struct input_dev *input;
	struct resource *res;
	int irq, error;

	irq = platform_get_irq(pdev, 0);
	if (irq < 0) {
		dev_err(&pdev->dev, "failed to get trkball irq\n");
		return -ENXIO;
	}

	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
	if (!res) {
		dev_err(&pdev->dev, "failed to get register memory\n");
		return -ENXIO;
	}

	trkball = kzalloc(sizeof(struct pxa930_trkball), GFP_KERNEL);
	if (!trkball)
		return -ENOMEM;

	trkball->pdata = pdev->dev.platform_data;
	if (!trkball->pdata) {
		dev_err(&pdev->dev, "no platform data defined\n");
		error = -EINVAL;
		goto failed;
	}

	trkball->mmio_base = ioremap_nocache(res->start, resource_size(res));
	if (!trkball->mmio_base) {
		dev_err(&pdev->dev, "failed to ioremap registers\n");
		error = -ENXIO;
		goto failed;
	}

	/*                                                     */
	pxa930_trkball_disable(trkball);

	error = request_irq(irq, pxa930_trkball_interrupt, 0,
			    pdev->name, trkball);
	if (error) {
		dev_err(&pdev->dev, "failed to request irq: %d\n", error);
		goto failed_free_io;
	}

	platform_set_drvdata(pdev, trkball);

	input = input_allocate_device();
	if (!input) {
		dev_err(&pdev->dev, "failed to allocate input device\n");
		error = -ENOMEM;
		goto failed_free_irq;
	}

	input->name = pdev->name;
	input->id.bustype = BUS_HOST;
	input->open = pxa930_trkball_open;
	input->close = pxa930_trkball_close;
	input->dev.parent = &pdev->dev;
	input_set_drvdata(input, trkball);

	trkball->input = input;

	input_set_capability(input, EV_REL, REL_X);
	input_set_capability(input, EV_REL, REL_Y);

	error = input_register_device(input);
	if (error) {
		dev_err(&pdev->dev, "unable to register input device\n");
		goto failed_free_input;
	}

	return 0;

failed_free_input:
	input_free_device(input);
failed_free_irq:
	free_irq(irq, trkball);
failed_free_io:
	iounmap(trkball->mmio_base);
failed:
	kfree(trkball);
	return error;
}

//.........这里部分代码省略.........
			adapter->rx_queue.queue_addr,
			adapter->rx_queue.queue_len, DMA_BIDIRECTIONAL);

	if ((dma_mapping_error(dev, adapter->buffer_list_dma)) ||
	    (dma_mapping_error(dev, adapter->filter_list_dma)) ||
	    (dma_mapping_error(dev, adapter->rx_queue.queue_dma))) {
		netdev_err(netdev, "unable to map filter or buffer list "
			   "pages\n");
		rc = -ENOMEM;
		goto err_out;
	}

	adapter->rx_queue.index = 0;
	adapter->rx_queue.num_slots = rxq_entries;
	adapter->rx_queue.toggle = 1;

	memcpy(&mac_address, netdev->dev_addr, netdev->addr_len);
	mac_address = mac_address >> 16;

	rxq_desc.fields.flags_len = IBMVETH_BUF_VALID |
					adapter->rx_queue.queue_len;
	rxq_desc.fields.address = adapter->rx_queue.queue_dma;

	netdev_dbg(netdev, "buffer list @ 0x%p\n", adapter->buffer_list_addr);
	netdev_dbg(netdev, "filter list @ 0x%p\n", adapter->filter_list_addr);
	netdev_dbg(netdev, "receive q   @ 0x%p\n", adapter->rx_queue.queue_addr);

	h_vio_signal(adapter->vdev->unit_address, VIO_IRQ_DISABLE);

	lpar_rc = ibmveth_register_logical_lan(adapter, rxq_desc, mac_address);

	if (lpar_rc != H_SUCCESS) {
		netdev_err(netdev, "h_register_logical_lan failed with %ld\n",
			   lpar_rc);
		netdev_err(netdev, "buffer TCE:0x%llx filter TCE:0x%llx rxq "
			   "desc:0x%llx MAC:0x%llx\n",
				     adapter->buffer_list_dma,
				     adapter->filter_list_dma,
				     rxq_desc.desc,
				     mac_address);
		rc = -ENONET;
		goto err_out;
	}

	for (i = 0; i < IBMVETH_NUM_BUFF_POOLS; i++) {
		if (!adapter->rx_buff_pool[i].active)
			continue;
		if (ibmveth_alloc_buffer_pool(&adapter->rx_buff_pool[i])) {
			netdev_err(netdev, "unable to alloc pool\n");
			adapter->rx_buff_pool[i].active = 0;
			rc = -ENOMEM;
			goto err_out;
		}
	}

	netdev_dbg(netdev, "registering irq 0x%x\n", netdev->irq);
	rc = request_irq(netdev->irq, ibmveth_interrupt, 0, netdev->name,
			 netdev);
	if (rc != 0) {
		netdev_err(netdev, "unable to request irq 0x%x, rc %d\n",
			   netdev->irq, rc);
		do {
			rc = h_free_logical_lan(adapter->vdev->unit_address);
		} while (H_IS_LONG_BUSY(rc) || (rc == H_BUSY));

		goto err_out;
	}

	adapter->bounce_buffer =
	    kmalloc(netdev->mtu + IBMVETH_BUFF_OH, GFP_KERNEL);
	if (!adapter->bounce_buffer) {
		netdev_err(netdev, "unable to allocate bounce buffer\n");
		rc = -ENOMEM;
		goto err_out_free_irq;
	}
	adapter->bounce_buffer_dma =
	    dma_map_single(&adapter->vdev->dev, adapter->bounce_buffer,
			   netdev->mtu + IBMVETH_BUFF_OH, DMA_BIDIRECTIONAL);
	if (dma_mapping_error(dev, adapter->bounce_buffer_dma)) {
		netdev_err(netdev, "unable to map bounce buffer\n");
		rc = -ENOMEM;
		goto err_out_free_irq;
	}

	netdev_dbg(netdev, "initial replenish cycle\n");
	ibmveth_interrupt(netdev->irq, netdev);

	netif_start_queue(netdev);

	netdev_dbg(netdev, "open complete\n");

	return 0;

err_out_free_irq:
	free_irq(netdev->irq, netdev);
err_out:
	ibmveth_cleanup(adapter);
	napi_disable(&adapter->napi);
	return rc;
}

/*
 * This function is called when the module is loaded
 */
static int __init sample_init_module(void)
{
	/*
 	 * Register device
 	 */
	int	ret;

	ret = register_chrdev(module_major, module_name, &sample_fops);
	if (ret < 0) {
		printk(KERN_INFO "%s: registering device %s with major %d failed with %d\n",
		       __func__, module_name, module_major, module_major );
		return(ret);
	}
	else
	{
		printk(KERN_INFO "%s: registering device %s with major %d\n",
		       __func__, module_name, module_major );
		/*
 		 * Reserve gpios
		*/
		if( gpio_request( TRIGGER, module_name ) )	// request pin D7 (trigger)
		{
			printk( KERN_INFO "%s: %s unable to get TRIG gpio\n", module_name, __func__ );
			ret = -EBUSY;
			return(ret);
		}

		if( gpio_request( ECHO, module_name ) )	// request pin D8 (echo)
		{
			printk( KERN_INFO "%s: %s unable to get ECHO gpio\n", module_name, __func__ );
			ret = -EBUSY;
			return(ret);
		}

		if( gpio_request( LED, module_name ) )	// request user LED GPIO
		{
			printk( KERN_INFO "%s: %s unable to get LED gpio\n", module_name, __func__ );
			ret = -EBUSY;
			return(ret);
		}

		/*
 		 * Set gpios directions
		*/
		if( gpio_direction_output( TRIGGER, 0 ) < 0 )	// Set pin D7 (trigger) as output with default value 0
		{
			printk( KERN_INFO "%s: %s unable to set TRIG gpio as output\n", module_name, __func__ );
			ret = -EBUSY;
			return(ret);
		}

		if( gpio_direction_input( ECHO ) < 0 )	// Set pin D8 (echo) as input
		{
			printk( KERN_INFO "%s: %s unable to set ECHO gpio as input\n", module_name, __func__ );
			ret = -EBUSY;
			return(ret);
		}

		if( gpio_direction_output( LED, 0 ) < 0 )	// Set LED gpio as output with default value 0
		{
			printk( KERN_INFO "%s: %s unable to set LED gpio as output\n", module_name, __func__ );
			ret = -EBUSY;
			return(ret);
		}

		// assign handler to ECHO pin IRQ
		if( request_irq( gpio_to_irq( ECHO ),		// IRQ of pin D8
                                 (irq_handler_t) echo_handler,	// ISR (callback)
				  IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING , // sensitive to either edge
				  module_name,
				  NULL ) < 0 )
		{
			printk( KERN_INFO "%s: %s unable to register gpio irq\n", module_name, __func__ );
			ret = -EBUSY;
			return( ret );
		}

		/* create the 2 needed workqueues */
		t_wq = create_workqueue( "Trigger wq" );
		if( t_wq )
		{
			INIT_WORK( (struct work_struct *)&trigger_work, trigger_wq_function );
		}

		led_wq = create_workqueue( "LED wq" );
		if( led_wq )
		{
			INIT_WORK( (struct work_struct *)&led_work, led_wq_function );
		}
	}

	return(ret);
}

static int gp2a_setup_irq(struct gp2a_data *gp2a)
{
	int rc = -EIO;
	struct gp2a_platform_data *pdata = gp2a->pdata;
	u8 value;

	gp2a_dbgmsg("start\n");

	rc = gpio_request(pdata->p_out, "gpio_proximity_out");
	if (rc < 0) {
		pr_err("%s: gpio %d request failed (%d)\n",
			__func__, pdata->p_out, rc);
		return rc;
	}

	rc = gpio_direction_input(pdata->p_out);
	if (rc < 0) {
		pr_err("%s: failed to set gpio %d as input (%d)\n",
			__func__, pdata->p_out, rc);
		goto err_gpio_direction_input;
	}

	value = 0x18;
	gp2a_i2c_write(gp2a, REGS_CON, &value);

	rc = request_irq(pdata->irq,
			 gp2a_irq_handler,
			 IRQF_TRIGGER_FALLING,
			 "proximity_int",
			 gp2a);

	if (rc < 0) {
		pr_err("%s: request_irq(%d) failed for gpio %d (%d)\n",
			__func__, pdata->irq,
			pdata->p_out, rc);
		goto err_request_irq;
	} else{
		pr_info("%s: request_irq(%d) success for gpio %d\n",
			__func__, pdata->irq, pdata->p_out);
	}
	/* start with interrupts disabled */
	disable_irq(pdata->irq);

	gp2a->val_state = 1;
	gp2a->power_state &= PROXIMITY_ENABLED;
	gp2a_dbgmsg("success\n");

	value = 0x08;
	gp2a_i2c_write(gp2a, REGS_GAIN, &value);
	value = nondetect;
	gp2a_i2c_write(gp2a, REGS_HYS, &value);
	value = 0x04;
	gp2a_i2c_write(gp2a, REGS_CYCLE, &value);
	value = 0x18;
	gp2a_i2c_write(gp2a, REGS_CON, &value);
	value = 0x02;
	gp2a_i2c_write(gp2a, REGS_OPMOD, &value);
	goto done;

err_request_irq:
err_gpio_direction_input:
	gpio_free(pdata->p_out);
done:
	return rc;
}

/* pdev is NULL for eisa */
static int __init cpqarray_register_ctlr( int i, struct pci_dev *pdev)
{
	struct request_queue *q;
	int j;

	/* 
	 * register block devices
	 * Find disks and fill in structs
	 * Get an interrupt, set the Q depth and get into /proc
	 */

	/* If this successful it should insure that we are the only */
	/* instance of the driver */
	if (register_blkdev(COMPAQ_SMART2_MAJOR+i, hba[i]->devname)) {
		goto Enomem4;
	}
	hba[i]->access.set_intr_mask(hba[i], 0);
	if (request_irq(hba[i]->intr, do_ida_intr,
		IRQF_DISABLED|IRQF_SHARED, hba[i]->devname, hba[i]))
	{
		printk(KERN_ERR "cpqarray: Unable to get irq %d for %s\n",
				hba[i]->intr, hba[i]->devname);
		goto Enomem3;
	}
		
	for (j=0; j<NWD; j++) {
		ida_gendisk[i][j] = alloc_disk(1 << NWD_SHIFT);
		if (!ida_gendisk[i][j])
			goto Enomem2;
	}

	hba[i]->cmd_pool = pci_alloc_consistent(
		hba[i]->pci_dev, NR_CMDS * sizeof(cmdlist_t),
		&(hba[i]->cmd_pool_dhandle));
	hba[i]->cmd_pool_bits = kcalloc(
		(NR_CMDS+BITS_PER_LONG-1)/BITS_PER_LONG, sizeof(unsigned long),
		GFP_KERNEL);

	if (!hba[i]->cmd_pool_bits || !hba[i]->cmd_pool)
			goto Enomem1;

	memset(hba[i]->cmd_pool, 0, NR_CMDS * sizeof(cmdlist_t));
	printk(KERN_INFO "cpqarray: Finding drives on %s",
		hba[i]->devname);

	spin_lock_init(&hba[i]->lock);
	q = blk_init_queue(do_ida_request, &hba[i]->lock);
	if (!q)
		goto Enomem1;

	hba[i]->queue = q;
	q->queuedata = hba[i];

	getgeometry(i);
	start_fwbk(i);

	ida_procinit(i);

	if (pdev)
		blk_queue_bounce_limit(q, hba[i]->pci_dev->dma_mask);

	/* This is a hardware imposed limit. */
	blk_queue_max_hw_segments(q, SG_MAX);

	/* This is a driver limit and could be eliminated. */
	blk_queue_max_phys_segments(q, SG_MAX);
	
	init_timer(&hba[i]->timer);
	hba[i]->timer.expires = jiffies + IDA_TIMER;
	hba[i]->timer.data = (unsigned long)hba[i];
	hba[i]->timer.function = ida_timer;
	add_timer(&hba[i]->timer);

	/* Enable IRQ now that spinlock and rate limit timer are set up */
	hba[i]->access.set_intr_mask(hba[i], FIFO_NOT_EMPTY);

	for(j=0; j<NWD; j++) {
		struct gendisk *disk = ida_gendisk[i][j];
		drv_info_t *drv = &hba[i]->drv[j];
		sprintf(disk->disk_name, "ida/c%dd%d", i, j);
		disk->major = COMPAQ_SMART2_MAJOR + i;
		disk->first_minor = j<<NWD_SHIFT;
		disk->fops = &ida_fops;
		if (j && !drv->nr_blks)
			continue;
		blk_queue_hardsect_size(hba[i]->queue, drv->blk_size);
		set_capacity(disk, drv->nr_blks);
		disk->queue = hba[i]->queue;
		disk->private_data = drv;
		add_disk(disk);
	}

	/* done ! */
	return(i);

Enomem1:
	nr_ctlr = i; 
	kfree(hba[i]->cmd_pool_bits);
	if (hba[i]->cmd_pool)
//.........这里部分代码省略.........

//.........这里部分代码省略.........
	socket_table[sockets].socket.owner = THIS_MODULE;
	/* only 16-bit cards, memory windows must be size-aligned */
	/* No PCI or CardBus support */
	socket_table[sockets].socket.features = SS_CAP_PCCARD | SS_CAP_MEM_ALIGN;
	/* irq 14, 11, 10, 7, 6, 5, 4, 3 */
	socket_table[sockets].socket.irq_mask = 0x4cf8;
	/* 4K minimum window size */
	socket_table[sockets].socket.map_size = 0x1000;		
	sockets++;
    }

    switch (socket_table[0].id) {
    case TCIC_ID_DB86082:
;
    case TCIC_ID_DB86082A:
;
    case TCIC_ID_DB86084:
;
    case TCIC_ID_DB86084A:
;
    case TCIC_ID_DB86072:
;
    case TCIC_ID_DB86184:
;
    case TCIC_ID_DB86082B:
;
    default:
;
    }
    
    /* Set up polling */
    poll_timer.function = &tcic_timer;
    poll_timer.data = 0;
    init_timer(&poll_timer);

    /* Build interrupt mask */
;
;
    if (irq_list_count == 0)
	mask = irq_mask;
    else
	for (i = mask = 0; i < irq_list_count; i++)
	    mask |= (1<<irq_list[i]);

    /* irq 14, 11, 10, 7, 6, 5, 4, 3 */
    mask &= 0x4cf8;
    /* Scan interrupts */
    mask = irq_scan(mask);
    for (i=0;i<sockets;i++)
	    socket_table[i].socket.irq_mask = mask;
    
    /* Check for only two interrupts available */
    scan = (mask & (mask-1));
    if (((scan & (scan-1)) == 0) && (poll_interval == 0))
	poll_interval = HZ;
    
    if (poll_interval == 0) {
	/* Avoid irq 12 unless it is explicitly requested */
	u_int cs_mask = mask & ((cs_irq) ? (1<<cs_irq) : ~(1<<12));
	for (i = 15; i > 0; i--)
	    if ((cs_mask & (1 << i)) &&
		(request_irq(i, tcic_interrupt, 0, "tcic",
			     tcic_interrupt) == 0))
		break;
	cs_irq = i;
	if (cs_irq == 0) poll_interval = HZ;
    }
    
    if (socket_table[0].socket.irq_mask & (1 << 11))
;
    if (cs_irq != 0)
;
    else
//	printk("polled status, interval = %d ms\n",
;
    
    for (i = 0; i < sockets; i++) {
	tcic_setw(TCIC_ADDR+2, socket_table[i].psock << TCIC_SS_SHFT);
	socket_table[i].last_sstat = tcic_getb(TCIC_SSTAT);
    }
    
    /* jump start interrupt handler, if needed */
    tcic_interrupt(0, NULL);

    platform_device_register(&tcic_device);

    for (i = 0; i < sockets; i++) {
	    socket_table[i].socket.ops = &tcic_operations;
	    socket_table[i].socket.resource_ops = &pccard_nonstatic_ops;
	    socket_table[i].socket.dev.parent = &tcic_device.dev;
	    ret = pcmcia_register_socket(&socket_table[i].socket);
	    if (ret && i)
		    pcmcia_unregister_socket(&socket_table[0].socket);
    }
    
    return ret;

    return 0;
    
} /* init_tcic */

static int b1pci_probe(struct capicardparams *p, struct pci_dev *pdev)
{
	avmcard *card;
	avmctrl_info *cinfo;
	int retval;

	card = b1_alloc_card(1);
	if (!card) {
		printk(KERN_WARNING "b1pci: no memory.\n");
		retval = -ENOMEM;
		goto err;
	}

	cinfo = card->ctrlinfo;
	sprintf(card->name, "b1pci-%x", p->port);
	card->port = p->port;
	card->irq = p->irq;
	card->cardtype = avm_b1pci;
	
	if (!request_region(card->port, AVMB1_PORTLEN, card->name)) {
		printk(KERN_WARNING "b1pci: ports 0x%03x-0x%03x in use.\n",
		       card->port, card->port + AVMB1_PORTLEN);
		retval = -EBUSY;
		goto err_free;
	}
	b1_reset(card->port);
	retval = b1_detect(card->port, card->cardtype);
	if (retval) {
		printk(KERN_NOTICE "b1pci: NO card at 0x%x (%d)\n",
		       card->port, retval);
		retval = -ENODEV;
		goto err_release_region;
	}
	b1_reset(card->port);
	b1_getrevision(card);
	
	retval = request_irq(card->irq, b1_interrupt, SA_SHIRQ, card->name, card);
	if (retval) {
		printk(KERN_ERR "b1pci: unable to get IRQ %d.\n", card->irq);
		retval = -EBUSY;
		goto err_release_region;
	}
	
	cinfo->capi_ctrl.driver_name   = "b1pci";
	cinfo->capi_ctrl.driverdata    = cinfo;
	cinfo->capi_ctrl.register_appl = b1_register_appl;
	cinfo->capi_ctrl.release_appl  = b1_release_appl;
	cinfo->capi_ctrl.send_message  = b1_send_message;
	cinfo->capi_ctrl.load_firmware = b1_load_firmware;
	cinfo->capi_ctrl.reset_ctr     = b1_reset_ctr;
	cinfo->capi_ctrl.procinfo      = b1pci_procinfo;
	cinfo->capi_ctrl.ctr_read_proc = b1ctl_read_proc;
	strcpy(cinfo->capi_ctrl.name, card->name);
	cinfo->capi_ctrl.owner         = THIS_MODULE;

	retval = attach_capi_ctr(&cinfo->capi_ctrl);
	if (retval) {
		printk(KERN_ERR "b1pci: attach controller failed.\n");
		goto err_free_irq;
	}

	if (card->revision >= 4) {
		printk(KERN_INFO "b1pci: AVM B1 PCI V4 at i/o %#x, irq %d, revision %d (no dma)\n",
		       card->port, card->irq, card->revision);
	} else {
		printk(KERN_INFO "b1pci: AVM B1 PCI at i/o %#x, irq %d, revision %d\n",
		       card->port, card->irq, card->revision);
	}

	pci_set_drvdata(pdev, card);
	return 0;

 err_free_irq:
	free_irq(card->irq, card);
 err_release_region:
	release_region(card->port, AVMB1_PORTLEN);
 err_free:
	b1_free_card(card);
 err:
	return retval;
}

//.........这里部分代码省略.........

	case SND_SOC_DAIFMT_DSP_A | SND_SOC_DAIFMT_CBM_CFM:
		/*
		 * DSP/PCM Mode A format, CODEC supplies BCLK and LRC clocks.
		 *
		 * The SSC transmit clock is obtained from the BCLK signal on
		 * on the TK line, and the SSC receive clock is
		 * generated from the transmit clock.
		 *
		 * Data is transferred on first BCLK after LRC pulse rising
		 * edge.If stereo, the right channel data is contiguous with
		 * the left channel data.
		 */
		rcmr =	  SSC_BF(RCMR_PERIOD, 0)
			| SSC_BF(RCMR_STTDLY, START_DELAY)
			| SSC_BF(RCMR_START, SSC_START_RISING_RF)
			| SSC_BF(RCMR_CKI, SSC_CKI_RISING)
			| SSC_BF(RCMR_CKO, SSC_CKO_NONE)
			| SSC_BF(RCMR_CKS, SSC_CKS_PIN);

		rfmr =	  SSC_BF(RFMR_FSEDGE, SSC_FSEDGE_POSITIVE)
			| SSC_BF(RFMR_FSOS, SSC_FSOS_NONE)
			| SSC_BF(RFMR_FSLEN, 0)
			| SSC_BF(RFMR_DATNB, (channels - 1))
			| SSC_BIT(RFMR_MSBF)
			| SSC_BF(RFMR_LOOP, 0)
			| SSC_BF(RFMR_DATLEN, (bits - 1));

		tcmr =	  SSC_BF(TCMR_PERIOD, 0)
			| SSC_BF(TCMR_STTDLY, START_DELAY)
			| SSC_BF(TCMR_START, SSC_START_RISING_RF)
			| SSC_BF(TCMR_CKI, SSC_CKI_FALLING)
			| SSC_BF(TCMR_CKO, SSC_CKO_NONE)
			| SSC_BF(TCMR_CKS, SSC_CKS_PIN);

		tfmr =	  SSC_BF(TFMR_FSEDGE, SSC_FSEDGE_POSITIVE)
			| SSC_BF(TFMR_FSDEN, 0)
			| SSC_BF(TFMR_FSOS, SSC_FSOS_NONE)
			| SSC_BF(TFMR_FSLEN, 0)
			| SSC_BF(TFMR_DATNB, (channels - 1))
			| SSC_BIT(TFMR_MSBF)
			| SSC_BF(TFMR_DATDEF, 0)
			| SSC_BF(TFMR_DATLEN, (bits - 1));
		break;

	default:
		printk(KERN_WARNING "atmel_ssc_dai: unsupported DAI format 0x%x\n",
			ssc_p->daifmt);
		return -EINVAL;
	}
	pr_debug("atmel_ssc_hw_params: "
			"RCMR=%08x RFMR=%08x TCMR=%08x TFMR=%08x\n",
			rcmr, rfmr, tcmr, tfmr);

	if (!ssc_p->initialized) {

		/* Enable PMC peripheral clock for this SSC */
		pr_debug("atmel_ssc_dai: Starting clock\n");
		clk_enable(ssc_p->ssc->clk);

		/* Reset the SSC and its PDC registers */
		ssc_writel(ssc_p->ssc->regs, CR, SSC_BIT(CR_SWRST));

		ssc_writel(ssc_p->ssc->regs, PDC_RPR, 0);
		ssc_writel(ssc_p->ssc->regs, PDC_RCR, 0);
		ssc_writel(ssc_p->ssc->regs, PDC_RNPR, 0);
		ssc_writel(ssc_p->ssc->regs, PDC_RNCR, 0);

		ssc_writel(ssc_p->ssc->regs, PDC_TPR, 0);
		ssc_writel(ssc_p->ssc->regs, PDC_TCR, 0);
		ssc_writel(ssc_p->ssc->regs, PDC_TNPR, 0);
		ssc_writel(ssc_p->ssc->regs, PDC_TNCR, 0);

		ret = request_irq(ssc_p->ssc->irq, atmel_ssc_interrupt, 0,
				ssc_p->name, ssc_p);
		if (ret < 0) {
			printk(KERN_WARNING
					"atmel_ssc_dai: request_irq failure\n");
			pr_debug("Atmel_ssc_dai: Stoping clock\n");
			clk_disable(ssc_p->ssc->clk);
			return ret;
		}

		ssc_p->initialized = 1;
	}

	/* set SSC clock mode register */
	ssc_writel(ssc_p->ssc->regs, CMR, ssc_p->cmr_div);

	/* set receive clock mode and format */
	ssc_writel(ssc_p->ssc->regs, RCMR, rcmr);
	ssc_writel(ssc_p->ssc->regs, RFMR, rfmr);

	/* set transmit clock mode and format */
	ssc_writel(ssc_p->ssc->regs, TCMR, tcmr);
	ssc_writel(ssc_p->ssc->regs, TFMR, tfmr);

	pr_debug("atmel_ssc_dai,hw_params: SSC initialized\n");
	return 0;
}