C++ sendCommandCheckAck函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中sendCommandCheckAck函数的典型用法代码示例。如果您正苦于以下问题：C++ sendCommandCheckAck函数的具体用法？C++ sendCommandCheckAck怎么用？C++ sendCommandCheckAck使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了sendCommandCheckAck函数的15个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: wirereaddata

uint32_t Adafruit_NFCShield_I2C::targetTxRx(char *DataOut,char *DataIn)
{
    ///////////////////////////////////// Receiving from Initiator ///////////////////////////
    pn532_packetbuffer[0] = PN532_COMMAND_TGGETDATA;
    if (! sendCommandCheckAck(pn532_packetbuffer, 1))
        return false;
    
    // read data packet
    wirereaddata(pn532_packetbuffer, 18+6);
    
#ifdef PN532DEBUG
    Serial.println();
    // check the response
    Serial.println("TARGET_RX");
    for(uint8_t i=0;i<18+6;i++)
    {
        Serial.print(pn532_packetbuffer[i], HEX); Serial.print(" ");
    }
#endif
    
    for(uint8_t iter=8;iter<(8+16);iter++)
    {
        DataIn[iter-8] = pn532_packetbuffer[iter]; //data received from initiator
    }
    
    ///////////////////////////////////// Sending to Initiator ///////////////////////////
    if(pn532_packetbuffer[7] == 0x00) //If no errors in receiving, send data.
    {
        pn532_packetbuffer[0] = PN532_COMMAND_TGSETDATA;
        for(uint8_t iter=(1+0);iter<(1+16);iter++)
        {
            pn532_packetbuffer[iter] = DataOut[iter-1]; //pack the data to send to target
        }
        
        if (! sendCommandCheckAck(pn532_packetbuffer, 17))
            return false;
        
        // read data packet
        wirereaddata(pn532_packetbuffer, 2+6);
        
#ifdef PN532DEBUG
        Serial.println();
        // check the response
        Serial.println("TARGET_TX");
        for(uint8_t i=0;i<2+6;i++)
        {
            Serial.print(pn532_packetbuffer[i], HEX); Serial.print(" ");
        }
#endif
        
        return (pn532_packetbuffer[7] == 0x00); //No error
    }
    
}

开发者ID:davidbliss，项目名称:Adafruit_NFCShield_I2C，代码行数:54，代码来源:Adafruit_NFCShield_I2C.cpp

示例2: Pins

boolean Adafruit_PN532::writeGPIO(uint8_t pinstate) {
  uint8_t errorbit;

  // Make sure pinstate does not try to toggle P32 or P34
  pinstate |= (1 << PN532_GPIO_P32) | (1 << PN532_GPIO_P34);
  
  // Fill command buffer
  pn532_packetbuffer[0] = PN532_COMMAND_WRITEGPIO;
  pn532_packetbuffer[1] = PN532_GPIO_VALIDATIONBIT | pinstate;  // P3 Pins
  pn532_packetbuffer[2] = 0x00;    // P7 GPIO Pins (not used ... taken by SPI)

  #ifdef PN532DEBUG
    puts("Writing P3 GPIO: "); puts(pn532_packetbuffer[1]); puts("Append leading 0 for small values riga 275");
  #endif

  // Send the WRITEGPIO command (0x0E)  
  if (! sendCommandCheckAck(pn532_packetbuffer, 3))
    return 0x0;
  
  // Read response packet (00 FF PLEN PLENCHECKSUM D5 CMD+1(0x0F) DATACHECKSUM 00)
  readspidata(pn532_packetbuffer, 8);

  #ifdef PN532DEBUG
    puts("Received: ");
   // PrintHex(pn532_packetbuffer, 8);
    puts("PrintHex riga 287");
    puts("");
  #endif  
  
  return  (pn532_packetbuffer[5] == 0x0F);
}

开发者ID:FrancescoErmini，项目名称:ThesisTest，代码行数:31，代码来源:Adafruit_PN532.cpp

示例3: readspidata

uint32_t Adafruit_PN532::getFirmwareVersion(void) {
  uint32_t response;

  pn532_packetbuffer[0] = PN532_COMMAND_GETFIRMWAREVERSION;
  
  if (! sendCommandCheckAck(pn532_packetbuffer, 1))
    return 0;
  
  // read data packet
  readspidata(pn532_packetbuffer, 12);
  
  // check some basic stuff
  if (0 != strncmp((char *)pn532_packetbuffer, (char *)pn532response_firmwarevers, 6)) {
    return 0;
  }
  
  response = pn532_packetbuffer[6];
  response <<= 8;
  response |= pn532_packetbuffer[7];
  response <<= 8;
  response |= pn532_packetbuffer[8];
  response <<= 8;
  response |= pn532_packetbuffer[9];

  return response;
}

开发者ID:FrancescoErmini，项目名称:ThesisTest，代码行数:26，代码来源:Adafruit_PN532.cpp

示例4: wirereaddata

uint32_t Adafruit_NFCShield_I2C::getFirmwareVersion(void) {
  uint32_t response;

  pn532_packetbuffer[0] = PN532_COMMAND_GETFIRMWAREVERSION;

  if (! sendCommandCheckAck(pn532_packetbuffer, 1))
    return 0;
	
  // read data packet
  wirereaddata(pn532_packetbuffer, 12);
  
  // check some basic stuff
  if (0 != strncmp((char *)pn532_packetbuffer, (char *)pn532response_firmwarevers, 6)) {
    #ifdef PN532DEBUG
    Serial.println("Firmware doesn't match!");
	#endif
    return 0;
  }
  
  response = pn532_packetbuffer[7];
  response <<= 8;
  response |= pn532_packetbuffer[8];
  response <<= 8;
  response |= pn532_packetbuffer[9];
  response <<= 8;
  response |= pn532_packetbuffer[10];

  return response;
}

开发者ID:logic-fault，项目名称:ethernet-QEL，代码行数:29，代码来源:Adafruit_NFCShield_I2C.cpp

示例5: Pins

boolean Adafruit_NFCShield_I2C::writeGPIO(uint8_t pinstate) {
  uint8_t errorbit;

  // Make sure pinstate does not try to toggle P32 or P34
  pinstate |= (1 << PN532_GPIO_P32) | (1 << PN532_GPIO_P34);
  
  // Fill command buffer
  pn532_packetbuffer[0] = PN532_COMMAND_WRITEGPIO;
  pn532_packetbuffer[1] = PN532_GPIO_VALIDATIONBIT | pinstate;  // P3 Pins
  pn532_packetbuffer[2] = 0x00;    // P7 GPIO Pins (not used ... taken by I2C)

  #ifdef PN532DEBUG
    Serial.print("Writing P3 GPIO: "); Serial.println(pn532_packetbuffer[1], HEX);
  #endif

  // Send the WRITEGPIO command (0x0E)  
  if (! sendCommandCheckAck(pn532_packetbuffer, 3))
    return 0x0;
  
  // Read response packet (00 00 FF PLEN PLENCHECKSUM D5 CMD+1(0x0F) DATACHECKSUM)
  wirereaddata(pn532_packetbuffer, 8);

  #ifdef PN532DEBUG
    Serial.print("Received: ");
    PrintHex(pn532_packetbuffer, 8);
    Serial.println("");
  #endif  
  
  return  (pn532_packetbuffer[6] == 0x0F);
}

开发者ID:logic-fault，项目名称:ethernet-QEL，代码行数:30，代码来源:Adafruit_NFCShield_I2C.cpp

示例6: Number

uint8_t Adafruit_NFCShield_I2C::mifareclassic_WriteDataBlock (uint8_t blockNumber, uint8_t * data)
{
  #ifdef MIFAREDEBUG
  Serial.print("Trying to write 16 bytes to block ");Serial.println(blockNumber);
  #endif
  
  /* Prepare the first command */
  pn532_packetbuffer[0] = PN532_COMMAND_INDATAEXCHANGE;
  pn532_packetbuffer[1] = 1;                      /* Card number */
  pn532_packetbuffer[2] = MIFARE_CMD_WRITE;       /* Mifare Write command = 0xA0 */
  pn532_packetbuffer[3] = blockNumber;            /* Block Number (0..63 for 1K, 0..255 for 4K) */
  memcpy (pn532_packetbuffer+4, data, 16);          /* Data Payload */

  /* Send the command */
  if (! sendCommandCheckAck(pn532_packetbuffer, 20))
  {
    #ifdef MIFAREDEBUG
    Serial.println("Failed to receive ACK for write command");
    #endif
    return 0;
  }  
  delay(10);
  
  /* Read the response packet */
  wirereaddata(pn532_packetbuffer, 26);

  return 1;  
}

开发者ID:logic-fault，项目名称:ethernet-QEL，代码行数:28，代码来源:Adafruit_NFCShield_I2C.cpp

示例7: once

boolean Adafruit_PN532::readPassiveTargetID(uint8_t cardbaudrate, uint8_t * uid, uint8_t * uidLength) {
  pn532_packetbuffer[0] = PN532_COMMAND_INLISTPASSIVETARGET;
  pn532_packetbuffer[1] = 1;  // max 1 cards at once (we can set this to 2 later)
  pn532_packetbuffer[2] = cardbaudrate;
  
  if (! sendCommandCheckAck(pn532_packetbuffer, 3))
    return 0x0;  // no cards read
  
  // read data packet
  readspidata(pn532_packetbuffer, 20);
  // check some basic stuff

  /* ISO14443A card response should be in the following format:
  
    byte            Description
    -------------   ------------------------------------------
    b0..6           Frame header and preamble
    b7              Tags Found
    b8              Tag Number (only one used in this example)
    b9..10          SENS_RES
    b11             SEL_RES
    b12             NFCID Length
    b13..NFCIDLen   NFCID                                      */
  
#ifdef MIFAREDEBUG
    puts("Found "); puts(pn532_packetbuffer[7], DEC); puts(" tags");
#endif
  if (pn532_packetbuffer[7] != 1) 
    return 0;
    
  uint16_t sens_res = pn532_packetbuffer[9];
  sens_res <<= 8;
  sens_res |= pn532_packetbuffer[10];
#ifdef MIFAREDEBUG
    puts("ATQA: 0x"); puts("riga 451"); // puts(sens_res, HEX);
    puts("SAK: 0x");  puts("riga 452");
#endif
  
  /* Card appears to be Mifare Classic */
  *uidLength = pn532_packetbuffer[12];
#ifdef MIFAREDEBUG
    puts("UID:");
#endif
  for (uint8_t i=0; i < pn532_packetbuffer[12]; i++) 
  {
    uid[i] = pn532_packetbuffer[13+i];
#ifdef MIFAREDEBUG
      puts(" 0x");puts("riga 464");
#endif
  }
#ifdef MIFAREDEBUG
    puts();
#endif

  return 1;
}

开发者ID:FrancescoErmini，项目名称:ThesisTest，代码行数:56，代码来源:Adafruit_PN532.cpp

示例8: digitalWrite

void Adafruit_PN532::begin() {
  digitalWrite(_ss, LOW);
  
  delay(1000);

  // not exactly sure why but we have to send a dummy command to get synced up
  pn532_packetbuffer[0] = PN532_COMMAND_GETFIRMWAREVERSION;
  sendCommandCheckAck(pn532_packetbuffer, 1);

  // ignore response!
}

开发者ID:FrancescoErmini，项目名称:ThesisTest，代码行数:11，代码来源:Adafruit_PN532.cpp

示例9:

boolean Adafruit_NFCShield_I2C::powerDown(uint32_t uiBlock) {
 
  pn532_packetbuffer[0] = PN532_COMMAND_POWERDOWN;
  pn532_packetbuffer[1] = (0xFF);  // I2C will wake up
  if (sendCommandCheckAck(pn532_packetbuffer, 2)){
#ifdef MIFAREDEBUG
    Serial.println("powered down");
#endif
    return 1;
  }

  return 0;
}

开发者ID:davidbliss，项目名称:Adafruit_NFCShield_I2C，代码行数:13，代码来源:Adafruit_NFCShield_I2C.cpp

示例10: delay

uint32_t Adafruit_NFCShield_I2C::configurePeerAsTarget() {
    
    byte pbuffer[38] =      { PN532_COMMAND_TGINITASTARGET,
        0x00,
        0x08, 0x00, //SENS_RES
        0x12, 0x34, 0x56, //NFCID1
        0x60, //SEL_RES
        
        0x01, 0xFE, 0xA2, 0xA3, 0xA4, 0xA5, 0xA6, 0xA7, // NFCID2t
        0xC0, 0xC1, 0xC2, 0xC3, 0xC4, 0xC5, 0xC6, 0xC7, //PAD
        0xFF, 0xFF, //System Code
        
        0xAA, 0x99, 0x88, 0x77, 0x66, 0x55, 0x44, 0x33, 0x22, 0x11, //NFCID3t: Change this to desired value
        
        0x00,  //Length of general bytes
        0x00  //Length of historical bytes
    };
    

    
    for(uint8_t iter=0;iter<38;iter++)
    {
        pn532_packetbuffer[iter] = pbuffer[iter];
    }
    
    if (! sendCommandCheckAck(pn532_packetbuffer, 38)){
#ifdef PN532DEBUG
        Serial.println("failed to recieve send ACK");
#endif
        return 0;
    }
    delay(6000);
    Serial.print("___");
    // read data packet
    wirereaddata(pn532_packetbuffer, 18+6);
    Serial.print("___");    
#ifdef PN532DEBUG
//    Serial.println();
    // check some basic stuff
    
//    Serial.println("PEER_TARGET");
//    for(uint8_t i=0;i<18+6;i++)
//    {
//        Serial.print(pn532_packetbuffer[i], HEX); Serial.println(" ");
//    }
#endif
    
    return (pn532_packetbuffer[23] == 0x00); //No error as it received all response
}

开发者ID:davidbliss，项目名称:Adafruit_NFCShield_I2C，代码行数:49，代码来源:Adafruit_NFCShield_I2C.cpp

示例11: memcpy

uint8_t Adafruit_NFCShield_I2C::mifareclassic_AuthenticateBlock (uint8_t * uid, uint8_t uidLen, uint32_t blockNumber, uint8_t keyNumber, uint8_t * keyData)
{
  uint8_t len;
  uint8_t i;
  
  // Hang on to the key and uid data
  memcpy (_key, keyData, 6); 
  memcpy (_uid, uid, uidLen); 
  _uidLen = uidLen;  

  #ifdef MIFAREDEBUG
  Serial.print("Trying to authenticate card ");
  Adafruit_NFCShield_I2C::PrintHex(_uid, _uidLen);
  Serial.print("Using authentication KEY ");Serial.print(keyNumber ? 'B' : 'A');Serial.print(": ");
  Adafruit_NFCShield_I2C::PrintHex(_key, 6);
  #endif
  
  // Prepare the authentication command //
  pn532_packetbuffer[0] = PN532_COMMAND_INDATAEXCHANGE;   /* Data Exchange Header */
  pn532_packetbuffer[1] = 1;                              /* Max card numbers */
  pn532_packetbuffer[2] = (keyNumber) ? MIFARE_CMD_AUTH_B : MIFARE_CMD_AUTH_A;
  pn532_packetbuffer[3] = blockNumber;                    /* Block Number (1K = 0..63, 4K = 0..255 */
  memcpy (pn532_packetbuffer+4, _key, 6);
  for (i = 0; i < _uidLen; i++)
  {
    pn532_packetbuffer[10+i] = _uid[i];                /* 4 byte card ID */
  }

  if (! sendCommandCheckAck(pn532_packetbuffer, 10+_uidLen))
    return 0;

  // Read the response packet
  wirereaddata(pn532_packetbuffer, 12);
  
  // Check if the response is valid and we are authenticated???
  // for an auth success it should be bytes 5-7: 0xD5 0x41 0x00
  // Mifare auth error is technically byte 7: 0x14 but anything other and 0x00 is not good
  if (pn532_packetbuffer[7] != 0x00)
  {
    #ifdef PN532DEBUG
    Serial.print("Authentification failed: ");
    Adafruit_PN532::PrintHexChar(pn532_packetbuffer, 12);
    #endif
    return 0;
  }  
  
  return 1;
}

开发者ID:440moparguy，项目名称:Adafruit_NFCShield_I2C，代码行数:48，代码来源:Adafruit_NFCShield_I2C.cpp

示例12: MxRtyATR

boolean Adafruit_NFCShield_I2C::setPassiveActivationRetries(uint8_t maxRetries) {
  pn532_packetbuffer[0] = PN532_COMMAND_RFCONFIGURATION;
  pn532_packetbuffer[1] = 5;    // Config item 5 (MaxRetries)
  pn532_packetbuffer[2] = 0xFF; // MxRtyATR (default = 0xFF)
  pn532_packetbuffer[3] = 0x01; // MxRtyPSL (default = 0x01)
  pn532_packetbuffer[4] = maxRetries;

#ifdef MIFAREDEBUG
  Serial.print("Setting MxRtyPassiveActivation to "); Serial.print(maxRetries, DEC); Serial.println(" ");
#endif
  
  if (! sendCommandCheckAck(pn532_packetbuffer, 5))
    return 0x0;  // no ACK
  
  return 1;
}

开发者ID:logic-fault，项目名称:ethernet-QEL，代码行数:16，代码来源:Adafruit_NFCShield_I2C.cpp

示例13: memcpy

uint8_t Adafruit_NFCShield_I2C::mifareclassic_AuthenticateBlock (uint8_t * uid, uint8_t uidLen, uint32_t blockNumber, uint8_t keyNumber, uint8_t * keyData)
{
  uint8_t len;
  uint8_t i;
  
  // Hang on to the key and uid data
  memcpy (_key, keyData, 6); 
  memcpy (_uid, uid, uidLen); 
  _uidLen = uidLen;  

  #ifdef MIFAREDEBUG
  Serial.print("Trying to authenticate card ");
  Adafruit_NFCShield_I2C::PrintHex(_uid, _uidLen);
  Serial.print("Using authentication KEY ");Serial.print(keyNumber ? 'B' : 'A');Serial.print(": ");
  Adafruit_NFCShield_I2C::PrintHex(_key, 6);
  #endif
  
  // Prepare the authentication command //
  pn532_packetbuffer[0] = PN532_COMMAND_INDATAEXCHANGE;   /* Data Exchange Header */
  pn532_packetbuffer[1] = 1;                              /* Max card numbers */
  pn532_packetbuffer[2] = (keyNumber) ? MIFARE_CMD_AUTH_A : MIFARE_CMD_AUTH_B;
  pn532_packetbuffer[3] = blockNumber;                    /* Block Number (1K = 0..63, 4K = 0..255 */
  memcpy (pn532_packetbuffer+4, _key, 6);
  for (i = 0; i < _uidLen; i++)
  {
    pn532_packetbuffer[10+i] = _uid[i];                /* 4 byte card ID */
  }

  if (! sendCommandCheckAck(pn532_packetbuffer, 10+_uidLen))
    return 0;

  // Read the response packet
  wirereaddata(pn532_packetbuffer, 12);
  // ToDo: How to check if the response is valid and we are authenticated???
  // #ifdef PN532DEBUG
  //   Serial.println("Authentification failed%s");
  // #endif
  // return 0;

  return 1;
}

开发者ID:logic-fault，项目名称:ethernet-QEL，代码行数:41，代码来源:Adafruit_NFCShield_I2C.cpp

示例14: once

boolean Adafruit_NFCShield_I2C::readPassiveTargetID(uint8_t cardbaudrate, uint8_t * uid, uint8_t * uidLength) {
  pn532_packetbuffer[0] = PN532_COMMAND_INLISTPASSIVETARGET;
  pn532_packetbuffer[1] = 1;  // max 1 cards at once (we can set this to 2 later)
  pn532_packetbuffer[2] = cardbaudrate;
  
  if (! sendCommandCheckAck(pn532_packetbuffer, 3))
  {
    #ifdef PN532DEBUG
	Serial.println("No card(s) read");
	#endif
    return 0x0;  // no cards read
  }
  
  // Wait for a card to enter the field
  uint8_t status = PN532_I2C_BUSY;
  #ifdef PN532DEBUG
  Serial.println("Waiting for IRQ (indicates card presence)");
  #endif
  while (wirereadstatus() != PN532_I2C_READY)
  {
	delay(10);
  }

  #ifdef PN532DEBUG
  Serial.println("Found a card"); 
  #endif
 
  // read data packet
  wirereaddata(pn532_packetbuffer, 20);
  
  // check some basic stuff
  /* ISO14443A card response should be in the following format:
  
    byte            Description
    -------------   ------------------------------------------
    b0..6           Frame header and preamble
    b7              Tags Found
    b8              Tag Number (only one used in this example)
    b9..10          SENS_RES
    b11             SEL_RES
    b12             NFCID Length
    b13..NFCIDLen   NFCID                                      */
  
#ifdef MIFAREDEBUG
    Serial.print("Found "); Serial.print(pn532_packetbuffer[7], DEC); Serial.println(" tags");
#endif
  if (pn532_packetbuffer[7] != 1) 
    return 0;
    
  uint16_t sens_res = pn532_packetbuffer[9];
  sens_res <<= 8;
  sens_res |= pn532_packetbuffer[10];
#ifdef MIFAREDEBUG
    Serial.print("ATQA: 0x");  Serial.println(sens_res, HEX); 
    Serial.print("SAK: 0x");  Serial.println(pn532_packetbuffer[11], HEX); 
#endif
  
  /* Card appears to be Mifare Classic */
  *uidLength = pn532_packetbuffer[12];
#ifdef MIFAREDEBUG
    Serial.print("UID:"); 
#endif
  for (uint8_t i=0; i < pn532_packetbuffer[12]; i++) 
  {
    uid[i] = pn532_packetbuffer[13+i];
#ifdef MIFAREDEBUG
      Serial.print(" 0x");Serial.print(uid[i], HEX); 
#endif
  }
#ifdef MIFAREDEBUG
    Serial.println();
#endif

  return 1;
}

开发者ID:logic-fault，项目名称:ethernet-QEL，代码行数:75，代码来源:Adafruit_NFCShield_I2C.cpp

示例15: wirereaddata

boolean Adafruit_NFCShield_I2C::inListPassiveTarget() {
  pn532_packetbuffer[0] = PN532_COMMAND_INLISTPASSIVETARGET;
  pn532_packetbuffer[1] = 1;
  pn532_packetbuffer[2] = 0;
  
  #ifdef PN532DEBUG 
    Serial.print("About to inList passive target");
  #endif

  if (!sendCommandCheckAck(pn532_packetbuffer,3,1000)) {
    #ifdef PN532DEBUG
      Serial.println("Could not send inlist message");
    #endif
    return false;
  }

  if (!waitUntilReady(30000)) {
    return false;
  }

  wirereaddata(pn532_packetbuffer,sizeof(pn532_packetbuffer));
  
  if (pn532_packetbuffer[0] == 0 && pn532_packetbuffer[1] == 0 && pn532_packetbuffer[2] == 0xff) {
    uint8_t length = pn532_packetbuffer[3];
    if (pn532_packetbuffer[4]!=(uint8_t)(~length+1)) {
      #ifdef PN532DEBUG
        Serial.println("Length check invalid");
        Serial.println(length,HEX);
        Serial.println((~length)+1,HEX);
      #endif
      return false;
    }
    if (pn532_packetbuffer[5]==PN532_PN532TOHOST && pn532_packetbuffer[6]==PN532_RESPONSE_INLISTPASSIVETARGET) {
      if (pn532_packetbuffer[7] != 1) {
        #ifdef PN532DEBUG
        Serial.println("Unhandled number of targets inlisted");
        #endif
        Serial.println("Number of tags inlisted:");
        Serial.println(pn532_packetbuffer[7]);
        return false;
      }
      
      inListedTag = pn532_packetbuffer[8];
      Serial.print("Tag number: ");
      Serial.println(inListedTag);
      
      return true;
    } else {
      #ifdef PN532DEBUG
        Serial.print("Unexpected response to inlist passive host");
      #endif
      return false;
    } 
  } 
  else {
    #ifdef PN532DEBUG
      Serial.println("Preamble missing");
    #endif
    return false;
  }

  return true;
}

开发者ID:440moparguy，项目名称:Adafruit_NFCShield_I2C，代码行数:63，代码来源:Adafruit_NFCShield_I2C.cpp

注：本文中的sendCommandCheckAck函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ sendCommandMessage函数代码示例发布时间：2022-05-30

C++ sendCmd函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：17943|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9562|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8126|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8505|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8409|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9299|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8373|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7805|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8356|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7358|2022-11-06

客服电话

电子邮件

C++ sendCommandCheckAck函数代码示例

示例1: wirereaddata

示例2: Pins

示例3: readspidata

示例4: wirereaddata

示例5: Pins

示例6: Number

示例7: once

示例8: digitalWrite

示例9:

示例10: delay

示例11: memcpy

示例12: MxRtyATR

示例13: memcpy

示例14: once

示例15: wirereaddata

请发表评论

全部评论

上一篇：

下一篇：

bradtraversy/iweather: Ionic 3 mobile we

断牙刷新位置时间（断牙属性及刷新位置介绍

MATLAB命令大全

更的笔顺,体会更的笔画,理会更的部首

ecki/net-tools: Linux base networking to

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053