• 设为首页
  • 点击收藏
  • 手机版
    手机扫一扫访问
    迪恩网络手机版
  • 关注官方公众号
    微信扫一扫关注
    迪恩网络公众号

sarkrui/NUC8i7BEH-Hackintosh-Build: [GUIDE] Installing macOS Mojave (10.14.x) on ...

原作者: [db:作者] 来自: 网络 收藏 邀请

开源软件名称(OpenSource Name):

sarkrui/NUC8i7BEH-Hackintosh-Build

开源软件地址(OpenSource Url):

https://github.com/sarkrui/NUC8i7BEH-Hackintosh-Build

开源编程语言(OpenSource Language):

Objective-C 49.8%

开源软件介绍(OpenSource Introduction):

[GUIDE] Building a Mac mini beast with NUC8i7BEH

Overview

This guide derives from @Rehabman's [Guide] Booting the OS X installer on LAPTOPS and [Guide] Intel NUC7NUC8 using Clover UEFI (NUC7i7Bxx,NUC8i7Bxx,etc) but the procedure has been simplified in order to provide a quick guide to install Mojave on the NUC8i7BEH.

92DB212A-A555-4BBD-81B8-854E1ED8B555

Performance

image-20190313124555196

image-20190313124640383

image-20190315211457246

Untitled-1

Specs

  • HyperX Impact DDR4 SODIMM 16GB * 1 (Recommend two sticks in dual-channel, 16GB of RAM works fine so far for me) Crucial DDR4 SODIMM 16GB I bought was not compatible with my NUC8. For more information about the recommended RAMs by Intel, see Memory Modules
  • Crucial MX500 1000G SATAIII SSD (I need the M.2 slot for Wi-FI/Bluetooth.)
  • Wi-Fi/Bluetooth Card
    • BCM943602CDP (4 antenna, IPEX1 connector) Wi-Fi/Bluetooth + M.2 NGFF Key B+M Adapter, Intel antenna replacement is required.
    • BCM94360CS2 (2 antenna IPEX4 connector) Wi-Fi/Bluetooth + M.2 NGFF Key B+M Adapter. Intel antenna replacement is NOT required but 2.4 GHz will have conflicts with bluetooth as they share the same connector.
  • M.2 NGFF Key B+M Adapter
  • LT Link Dual Thunderbolt 3 eGPU Dock
  • Sapphire RX 460 4G (firmware upgraded to RX 560)
  • Mojave 10.14.2 Final Cut Pro has better performance on 10.14.2, less exporting time and better stability than the performance on 10.14.3.

Works

  • AirDrop, Handoff (Apple Wi-Fi/Bluetooth required)
  • iMessage (complete serial required)
  • All USB3.1 Gen1/USB2.0 ports
  • USB3.1 Type-c Hotplugging
  • Hardware Acceleration (Final Cut Pro X, VideoProc, Compressor tested.)
  • Thunderbolt 3 eGPU (Final Cut Pro X, VideoProc, Compressor tested.)

Not working

  • Thunderbolt 3 eGPU Hotplugging

Preparation

BIOS settings

  • BIOS version 0056 (Please do not use the latest one, 0064. If so, please downgrade to 0056, I have attached the firmware in the respository since it was no longer provided from Intel support.)

BIOS setup can be accessed by mashing the F2 key while booting up. It will get you to the main BIOS setup screens. To start, choose "Load Defaults" (choose from the menu or press F9 in the BIOS setup).

Then change:

  • Boot -> Boot Configuration, disable "Network Boot"
  • Power -> Secondary Power Settings, "Wake on LAN from S4/S5", set to "Stay Off"
  • Boot -> Secure Boot, disable "Secure Boot"
  • Devices -> OnBoard Devices, disable "Bluetooth" (macOS is not compatible well with Intel Wi-Fi/Bluetooth)

Suggested:

  • Boot -> Boot Priority -> Legacy Boot Priority, enable "Legacy Boot".

Installation

Option 1: GUI (recommended)

Option 2: Command-line

Note: If you get an error that says "This copy of the Install macOS Mojave.app application is damaged, and can’t be used to install macOS", then open up a terminal and set the date to March 3rd, 2019 at 00:00 with date 030300002019

Post-installation

Clover EFI

  • Download the latest EFI Clover (see release)
  • Mount EFI folder with EFI Mounter V3 or Clover Configurator
  • Place the downloaded EFI folder in your local EFI drive

Fixing Continuity

Wi-Fi/Bluetooth Adapter

Untitled-1

  • 2-pin JST 1.00mm (pitch) connected to the adapter
  • 4-pin JST 1.25mm (pitch) connected to the NUC internal USB2.0 connector (see "G" "H")
Scheme

BT_InternalUSBHeader_Scheme

IPEX1 Antennas

The original antennas on NUC are using IPEX4 connector while the BCM943602CDP is using IPEX1. Thus, I completely removed the original ones and replaced them with four IPEX1. However, it's worth mentioning that the quality of the signal drops after the replacement (for both Wi-Fi and Bluetooth).

Continuity Activation Tool (C.A.T)

To enable conitinuity, you must have an invaild serial number (meaning never been used by other Macs), for detailed information, please check Generating invaild serial number from hackintosher. If everything is ready and yet you still cannot have AirDrop and Handoff, please try C.A.T to activate continuity.

FRC Reverse Proxy

Frp is a fast reverse proxy to help you expose a local server behind a NAT or firewall to the internet. As of now, it supports TCP & UDP, as well as http and https protocols, where requests can be forwarded to internal services by domain name. For example, with Frp, VNC port (5900), SSH port (22), and FTP port (445) on Macs behind a NAT, can be exposed to the public. Therefore, a user can have access to Screen Sharing, File Sharing remotely.

Credit

  • Thanks @RehabMan for the initial development of installing guide for NUC series.

  • Thanks @Daliansky for providing the installing guide and clover config library for common PCs.

  • Thanks @GoingDark for contributing the internal USB headers id.




鲜花

握手

雷人

路过

鸡蛋
该文章已有0人参与评论

请发表评论

全部评论

专题导读
热门推荐
阅读排行榜

扫描微信二维码

查看手机版网站

随时了解更新最新资讯

139-2527-9053

在线客服(服务时间 9:00~18:00)

在线QQ客服
地址:深圳市南山区西丽大学城创智工业园
电邮:jeky_zhao#qq.com
移动电话:139-2527-9053

Powered by 互联科技 X3.4© 2001-2213 极客世界.|Sitemap