开源软件名称：

开源软件地址：

开源编程语言：

开源软件介绍：

homebridge-foscam-ng

Foscam camera plugin for Homebridge

Configuration

Configuration sample:

    "platforms": [
        {
            "platform": "Foscam-NG",
            "username": "username",
            "password": "password",
            "host": "192.168.0.121",
            "port": 88,
            "gain": 6,
            "motionDetector": {
                "schedule": {
                    "monday": [["0:00", "24:00"]],
                    "tuesday": [["0:00", "24:00"]],
                    "wednesday": [["0:00", "24:00"]],
                    "thursday": [["0:00", "24:00"]],
                    "friday": [["0:00", "24:00"]],
                    "saturday": [["0:00", "24:00"]],
                    "sunday": [["0:00", "24:00"]]
                },

                "areas": [
                    [[0, 0], [9, 9]]
                ]
            },
            "speaker": {
                "enabled": true,
                "compression": true,
                "gain": 1
            }
        }

Fields:

• "platform": Must always be "Foscam-NG" (required)
• "username": The username for your Foscam camera. Manufacturer default is "admin". (required)
• "password": The password for your Foscam camera. Manufacturer default for "admin" is "". (required)
• "host": The local IP address of your camera. (required)
• "port": The HTTP port for the camera. Manufacturer default is 88. (required)
• "rtspPort": The RTSP port for the camera. Will automatically detect if possible, and will default to HTTP port if not possible. (optional)
• "gain": Foscam audio output tends to be on the quiet side. This is the gain in decibels to boost the audio. Use 0 for no gain. (required)
• "streamType": Video setting to overwrite for iOS's dynamic configuration. Defaults to 3 ("user-defined"). (optional)
• "maxMainStreams": Number of simultaneous streams to allow from the camera's "main" stream. Defaults to 2. (optional)
• "maxSubStreams": Number of simultaneous streams to allow from the camera's "main" stream. Defaults to 2. (optional)
• "motionDetector": Add if motion detector feature is desired. Note that enabling this will overwrite any existing motion detection settings on the Foscam. (optional)
  • "schedule": If not present, motion detector is always active. If present, specifies the days and time intervals during which the motion detector is active. Each day is a list of one or more time intervals. Time intervals are a list with two items, a start time (inclusive) and a stop time (exclusive). All time is in 24 hour format, with 24:00 denoting the end of the day. Due to Foscam limitations, minutes are only honored in 30 minute increments. (optional)
  • "areas": If not present, the motion detector will work on the entire image. If present, specifies the areas of the image the motion detector should pay attention to. This is a list of rectangular areas. Each rectangular area is a list with two items, a top left coordinate and a bottom right coordinate. Each coordinate is a list with two items, an x coordinate and a y coordinate. Foscam divides the image into a 10x10 grid, with the top left grid being 0, 0 and the bottom right being 9, 9.
  • "triggerInterval": Time in seconds (5-15) to consider the motion detection triggered after detecting a motion, suppressing additional detection of motion during that time period. Defaults to 5. (optional)
  • "sensitivity": 0 for low, 1 for normal, 2 for high, 3 for lower, 4 for lowest. Defaults to 1. (optional)
• "speaker": Add to configure speaker settings. Defaults to enabled. (optional)
  • "enabled": Set to false to disable. Defaults to true. (optional)
  • "compression": Set to false to disable compression. No compression can result in better quality at the cost of 8 times more bandwidth. Defaults to true. (optional)
  • "gain": This is gain in decibels to boost the speaker volume. Defaults to 0. (optional)