本文整理汇总了C++中setup_isac函数的典型用法代码示例。如果您正苦于以下问题：C++ setup_isac函数的具体用法？C++ setup_isac怎么用？C++ setup_isac使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。
在下文中一共展示了setup_isac函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。
示例1: njs_cs_init_rest
static int __devinit njs_cs_init_rest(struct IsdnCard *card,
struct IsdnCardState *cs)
{
const int bytecnt = 256;
printk(KERN_INFO
"NETjet-S: %s card configured at %#lx IRQ %d\n",
cs->subtyp ? "TJ320" : "TJ300", cs->hw.njet.base, cs->irq);
if (!request_region(cs->hw.njet.base, bytecnt, "netjet-s isdn")) {
printk(KERN_WARNING
"HiSax: NETjet-S config port %#lx-%#lx already in use\n",
cs->hw.njet.base,
cs->hw.njet.base + bytecnt);
return (0);
}
cs->readisac = &NETjet_ReadIC;
cs->writeisac = &NETjet_WriteIC;
cs->readisacfifo = &NETjet_ReadICfifo;
cs->writeisacfifo = &NETjet_WriteICfifo;
cs->BC_Read_Reg = &dummyrr;
cs->BC_Write_Reg = &dummywr;
cs->BC_Send_Data = &netjet_fill_dma;
setup_isac(cs);
cs->cardmsg = &NETjet_S_card_msg;
cs->irq_func = &netjet_s_interrupt;
cs->irq_flags |= IRQF_SHARED;
ISACVersion(cs, "NETjet-S:");
return (1);
}
开发者ID:12019，项目名称:kernel_zte_u880，代码行数:30，代码来源:nj_s.c
示例2: setup_sportster
int __init
setup_sportster(struct IsdnCard *card)
{
struct IsdnCardState *cs = card->cs;
char tmp[64];
strcpy(tmp, sportster_revision);
printk(KERN_INFO "HiSax: USR Sportster driver Rev. %s\n", HiSax_getrev(tmp));
if (cs->typ != ISDN_CTYPE_SPORTSTER)
return (0);
cs->hw.spt.cfg_reg = card->para[1];
cs->irq = card->para[0];
if (!get_io_range(cs))
return (0);
cs->hw.spt.isac = cs->hw.spt.cfg_reg + SPORTSTER_ISAC;
cs->hw.spt.hscx[0] = cs->hw.spt.cfg_reg + SPORTSTER_HSCXA;
cs->hw.spt.hscx[1] = cs->hw.spt.cfg_reg + SPORTSTER_HSCXB;
switch(cs->irq) {
case 5: cs->hw.spt.res_irq = 1;
break;
case 7: cs->hw.spt.res_irq = 2;
break;
case 10:cs->hw.spt.res_irq = 3;
break;
case 11:cs->hw.spt.res_irq = 4;
break;
case 12:cs->hw.spt.res_irq = 5;
break;
case 14:cs->hw.spt.res_irq = 6;
break;
case 15:cs->hw.spt.res_irq = 7;
break;
default:release_io_sportster(cs);
printk(KERN_WARNING "Sportster: wrong IRQ\n");
return(0);
}
printk(KERN_INFO "HiSax: %s config irq:%d cfg:0x%X\n",
CardType[cs->typ], cs->irq, cs->hw.spt.cfg_reg);
setup_isac(cs);
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->BC_Read_Reg = &ReadHSCX;
cs->BC_Write_Reg = &WriteHSCX;
cs->BC_Send_Data = &hscx_fill_fifo;
cs->cardmsg = &Sportster_card_msg;
cs->irq_func = &sportster_interrupt;
ISACVersion(cs, "Sportster:");
if (HscxVersion(cs, "Sportster:")) {
printk(KERN_WARNING
"Sportster: wrong HSCX versions check IO address\n");
release_io_sportster(cs);
return (0);
}
return (1);
}
开发者ID:jameshilliard，项目名称:actiontec_opensrc_mi424wr-rev-ef_fw-20-19-8，代码行数:59，代码来源:sportster.c
示例3: setup_saphir
int __init
setup_saphir(struct IsdnCard *card)
{
struct IsdnCardState *cs = card->cs;
char tmp[64];
strcpy(tmp, saphir_rev);
printk(KERN_INFO "HiSax: HST Saphir driver Rev. %s\n", HiSax_getrev(tmp));
if (cs->typ != ISDN_CTYPE_HSTSAPHIR)
return (0);
/* IO-Ports */
cs->hw.saphir.cfg_reg = card->para[1];
cs->hw.saphir.isac = card->para[1] + ISAC_DATA;
cs->hw.saphir.hscx = card->para[1] + HSCX_DATA;
cs->hw.saphir.ale = card->para[1] + ADDRESS_REG;
cs->irq = card->para[0];
if (!request_region(cs->hw.saphir.cfg_reg, 6, "saphir")) {
printk(KERN_WARNING
"HiSax: %s config port %x-%x already in use\n",
CardType[card->typ],
cs->hw.saphir.cfg_reg,
cs->hw.saphir.cfg_reg + 5);
return (0);
}
printk(KERN_INFO "HiSax: %s config irq:%d io:0x%X\n",
CardType[cs->typ], cs->irq, cs->hw.saphir.cfg_reg);
setup_isac(cs);
cs->hw.saphir.timer.function = (void *) SaphirWatchDog;
cs->hw.saphir.timer.data = (long) cs;
init_timer(&cs->hw.saphir.timer);
cs->hw.saphir.timer.expires = jiffies + 4*HZ;
add_timer(&cs->hw.saphir.timer);
if (saphir_reset(cs)) {
release_io_saphir(cs);
return (0);
}
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->BC_Read_Reg = &ReadHSCX;
cs->BC_Write_Reg = &WriteHSCX;
cs->BC_Send_Data = &hscx_fill_fifo;
cs->cardmsg = &saphir_card_msg;
cs->irq_func = &saphir_interrupt;
ISACVersion(cs, "saphir:");
if (HscxVersion(cs, "saphir:")) {
printk(KERN_WARNING
"saphir: wrong HSCX versions check IO address\n");
release_io_saphir(cs);
return (0);
}
return (1);
}
开发者ID:Antonio-Zhou，项目名称:Linux-2.6.11，代码行数:57，代码来源:saphir.c
示例4: setup_avm_a1_pcmcia
int
setup_avm_a1_pcmcia(struct IsdnCard *card)
{
u_char model, vers;
struct IsdnCardState *cs = card->cs;
char tmp[64];
strcpy(tmp, avm_revision);
printk(KERN_INFO "HiSax: AVM A1 PCMCIA driver Rev. %s\n",
HiSax_getrev(tmp));
if (cs->typ != ISDN_CTYPE_A1_PCMCIA)
return (0);
cs->hw.avm.cfg_reg = card->para[1];
cs->irq = card->para[0];
byteout(cs->hw.avm.cfg_reg+ASL1_OFFSET, ASL1_W_ENABLE_S0);
byteout(cs->hw.avm.cfg_reg+ASL0_OFFSET,0x00);
HZDELAY(HZ / 5 + 1);
byteout(cs->hw.avm.cfg_reg+ASL0_OFFSET,ASL0_W_RESET);
HZDELAY(HZ / 5 + 1);
byteout(cs->hw.avm.cfg_reg+ASL0_OFFSET,0x00);
byteout(cs->hw.avm.cfg_reg+ASL0_OFFSET, ASL0_W_TDISABLE|ASL0_W_TRESET);
model = bytein(cs->hw.avm.cfg_reg+MODREG_OFFSET);
vers = bytein(cs->hw.avm.cfg_reg+VERREG_OFFSET);
printk(KERN_INFO "AVM A1 PCMCIA: io 0x%x irq %d model %d version %d\n",
cs->hw.avm.cfg_reg, cs->irq, model, vers);
setup_isac(cs);
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->BC_Read_Reg = &ReadHSCX;
cs->BC_Write_Reg = &WriteHSCX;
cs->BC_Send_Data = &hscx_fill_fifo;
cs->cardmsg = &AVM_card_msg;
cs->irq_flags = IRQF_SHARED;
cs->irq_func = &avm_a1p_interrupt;
ISACVersion(cs, "AVM A1 PCMCIA:");
if (HscxVersion(cs, "AVM A1 PCMCIA:")) {
printk(KERN_WARNING
"AVM A1 PCMCIA: wrong HSCX versions check IO address\n");
return (0);
}
return (1);
}
开发者ID:DentonGentry，项目名称:gfiber-gfrg100，代码行数:53，代码来源:avm_a1p.c
示例5: setup_gazelisa
static int __devinit
setup_gazelisa(struct IsdnCard *card, struct IsdnCardState *cs)
{
printk(KERN_INFO "Gazel: ISA PnP card automatic recognition\n");
// we got an irq parameter, assume it is an ISA card
// R742 decodes address even in not started...
// R647 returns FF if not present or not started
// eventually needs improvment
if (readreg_ipac(card->para[1], IPAC_ID) == 1)
cs->subtyp = R742;
else
cs->subtyp = R647;
setup_isac(cs);
cs->hw.gazel.cfg_reg = card->para[1] + 0xC000;
cs->hw.gazel.ipac = card->para[1];
cs->hw.gazel.isac = card->para[1] + 0x8000;
cs->hw.gazel.hscx[0] = card->para[1];
cs->hw.gazel.hscx[1] = card->para[1] + 0x4000;
cs->irq = card->para[0];
cs->hw.gazel.isacfifo = cs->hw.gazel.isac;
cs->hw.gazel.hscxfifo[0] = cs->hw.gazel.hscx[0];
cs->hw.gazel.hscxfifo[1] = cs->hw.gazel.hscx[1];
switch (cs->subtyp) {
case R647:
printk(KERN_INFO "Gazel: Card ISA R647/R648 found\n");
cs->dc.isac.adf2 = 0x87;
printk(KERN_INFO
"Gazel: config irq:%d isac:0x%X cfg:0x%X\n",
cs->irq, cs->hw.gazel.isac, cs->hw.gazel.cfg_reg);
printk(KERN_INFO
"Gazel: hscx A:0x%X hscx B:0x%X\n",
cs->hw.gazel.hscx[0], cs->hw.gazel.hscx[1]);
break;
case R742:
printk(KERN_INFO "Gazel: Card ISA R742 found\n");
test_and_set_bit(HW_IPAC, &cs->HW_Flags);
printk(KERN_INFO
"Gazel: config irq:%d ipac:0x%X\n",
cs->irq, cs->hw.gazel.ipac);
break;
}
return (0);
}
开发者ID:PennPanda，项目名称:linux-repo，代码行数:47，代码来源:gazel.c
示例6: a4t_cs_init
static int __devinit a4t_cs_init(struct IsdnCard *card,
struct IsdnCardState *cs,
u_int pci_memaddr)
{
I20_REGISTER_FILE *pI20_Regs;
if (!cs->irq) { /* IRQ range check ?? */
printk(KERN_WARNING "HiSax: Telekom A4T: No IRQ\n");
return (0);
}
cs->hw.ax.base = (long) ioremap(pci_memaddr, 4096);
/* Check suspecious address */
pI20_Regs = (I20_REGISTER_FILE *) (cs->hw.ax.base);
if ((pI20_Regs->i20IntStatus & 0x8EFFFFFF) != 0) {
printk(KERN_WARNING "HiSax: Telekom A4T address "
"%lx-%lx suspicious\n",
cs->hw.ax.base, cs->hw.ax.base + 4096);
iounmap((void *) cs->hw.ax.base);
cs->hw.ax.base = 0;
return (0);
}
cs->hw.ax.isac_adr = cs->hw.ax.base + PO_OFFSET;
cs->hw.ax.jade_adr = cs->hw.ax.base + PO_OFFSET;
cs->hw.ax.isac_ale = GCS_1;
cs->hw.ax.jade_ale = GCS_3;
printk(KERN_INFO "HiSax: Telekom A4T: Card configured at "
"0x%lX IRQ %d\n",
cs->hw.ax.base, cs->irq);
setup_isac(cs);
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->BC_Read_Reg = &ReadJADE;
cs->BC_Write_Reg = &WriteJADE;
cs->BC_Send_Data = &jade_fill_fifo;
cs->cardmsg = &BKM_card_msg;
cs->irq_func = &bkm_interrupt;
cs->irq_flags |= IRQF_SHARED;
ISACVersion(cs, "Telekom A4T:");
/* Jade version */
JadeVersion(cs, "Telekom A4T:");
return (1);
}
开发者ID:openube，项目名称:android_kernel_sony_c2305，代码行数:47，代码来源:bkm_a4t.c
示例7: setup_isurf
int __devinit
setup_isurf(struct IsdnCard *card)
{
int ver;
struct IsdnCardState *cs = card->cs;
char tmp[64];
strcpy(tmp, ISurf_revision);
printk(KERN_INFO "HiSax: ISurf driver Rev. %s\n", HiSax_getrev(tmp));
if (cs->typ != ISDN_CTYPE_ISURF)
return(0);
if (card->para[1] && card->para[2]) {
cs->hw.isurf.reset = card->para[1];
cs->hw.isurf.phymem = card->para[2];
cs->irq = card->para[0];
} else {
#ifdef __ISAPNP__
if (isapnp_present()) {
struct pnp_dev *pnp_d = NULL;
int err;
cs->subtyp = 0;
if ((pnp_c = pnp_find_card(
ISAPNP_VENDOR('S', 'I', 'E'),
ISAPNP_FUNCTION(0x0010), pnp_c))) {
if (!(pnp_d = pnp_find_dev(pnp_c,
ISAPNP_VENDOR('S', 'I', 'E'),
ISAPNP_FUNCTION(0x0010), pnp_d))) {
printk(KERN_ERR "ISurfPnP: PnP error card found, no device\n");
return (0);
}
pnp_disable_dev(pnp_d);
err = pnp_activate_dev(pnp_d);
cs->hw.isurf.reset = pnp_port_start(pnp_d, 0);
cs->hw.isurf.phymem = pnp_mem_start(pnp_d, 1);
cs->irq = pnp_irq(pnp_d, 0);
if (!cs->irq || !cs->hw.isurf.reset || !cs->hw.isurf.phymem) {
printk(KERN_ERR "ISurfPnP:some resources are missing %d/%x/%lx\n",
cs->irq, cs->hw.isurf.reset, cs->hw.isurf.phymem);
pnp_disable_dev(pnp_d);
return(0);
}
} else {
printk(KERN_INFO "ISurfPnP: no ISAPnP card found\n");
return(0);
}
} else {
printk(KERN_INFO "ISurfPnP: no ISAPnP bus found\n");
return(0);
}
#else
printk(KERN_WARNING "HiSax: Siemens I-Surf port/mem not set\n");
return (0);
#endif
}
if (!request_region(cs->hw.isurf.reset, 1, "isurf isdn")) {
printk(KERN_WARNING
"HiSax: Siemens I-Surf config port %x already in use\n",
cs->hw.isurf.reset);
return (0);
}
if (!request_region(cs->hw.isurf.phymem, ISURF_IOMEM_SIZE, "isurf iomem")) {
printk(KERN_WARNING "HiSax: Siemens I-Surf memory region "
"%lx-%lx already in use\n",
cs->hw.isurf.phymem,
cs->hw.isurf.phymem + ISURF_IOMEM_SIZE);
release_region(cs->hw.isurf.reset, 1);
return (0);
}
cs->hw.isurf.isar = ioremap(cs->hw.isurf.phymem, ISURF_IOMEM_SIZE);
cs->hw.isurf.isac = cs->hw.isurf.isar + ISURF_ISAC_OFFSET;
printk(KERN_INFO
"ISurf: defined at 0x%x 0x%lx IRQ %d\n",
cs->hw.isurf.reset,
cs->hw.isurf.phymem,
cs->irq);
setup_isac(cs);
cs->cardmsg = &ISurf_card_msg;
cs->irq_func = &isurf_interrupt;
cs->auxcmd = &isurf_auxcmd;
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->bcs[0].hw.isar.reg = &cs->hw.isurf.isar_r;
cs->bcs[1].hw.isar.reg = &cs->hw.isurf.isar_r;
test_and_set_bit(HW_ISAR, &cs->HW_Flags);
ISACVersion(cs, "ISurf:");
cs->BC_Read_Reg = &ReadISAR;
cs->BC_Write_Reg = &WriteISAR;
cs->BC_Send_Data = &isar_fill_fifo;
ver = ISARVersion(cs, "ISurf:");
if (ver < 0) {
printk(KERN_WARNING
"ISurf: wrong ISAR version (ret = %d)\n", ver);
release_io_isurf(cs);
return (0);
}
//.........这里部分代码省略.........
开发者ID:robacklin，项目名称:ts4700，代码行数:101，代码来源:isurf.c
示例8: setup_bkm_a4t
int __init
setup_bkm_a4t(struct IsdnCard *card)
{
struct IsdnCardState *cs = card->cs;
char tmp[64];
u_int pci_memaddr = 0, found = 0;
I20_REGISTER_FILE *pI20_Regs;
#ifdef CONFIG_PCI
#endif
strcpy(tmp, bkm_a4t_revision);
printk(KERN_INFO "HiSax: T-Berkom driver Rev. %s\n", HiSax_getrev(tmp));
if (cs->typ == ISDN_CTYPE_BKM_A4T) {
cs->subtyp = BKM_A4T;
} else
return (0);
#ifdef CONFIG_PCI
while ((dev_a4t = pci_find_device(PCI_VENDOR_ID_ZORAN,
PCI_DEVICE_ID_ZORAN_36120, dev_a4t))) {
u16 sub_sys;
u16 sub_vendor;
sub_vendor = dev_a4t->subsystem_vendor;
sub_sys = dev_a4t->subsystem_device;
if ((sub_sys == PCI_DEVICE_ID_BERKOM_A4T) && (sub_vendor == PCI_VENDOR_ID_BERKOM)) {
if (pci_enable_device(dev_a4t))
return(0);
found = 1;
pci_memaddr = pci_resource_start(dev_a4t, 0);
cs->irq = dev_a4t->irq;
break;
}
}
if (!found) {
printk(KERN_WARNING "HiSax: %s: Card not found\n", CardType[card->typ]);
return (0);
}
if (!cs->irq) { /* IRQ range check ?? */
printk(KERN_WARNING "HiSax: %s: No IRQ\n", CardType[card->typ]);
return (0);
}
if (!pci_memaddr) {
printk(KERN_WARNING "HiSax: %s: No Memory base address\n", CardType[card->typ]);
return (0);
}
cs->hw.ax.base = (long) ioremap(pci_memaddr, 4096);
/* Check suspecious address */
pI20_Regs = (I20_REGISTER_FILE *) (cs->hw.ax.base);
if ((pI20_Regs->i20IntStatus & 0x8EFFFFFF) != 0) {
printk(KERN_WARNING "HiSax: %s address %lx-%lx suspecious\n",
CardType[card->typ], cs->hw.ax.base, cs->hw.ax.base + 4096);
iounmap((void *) cs->hw.ax.base);
cs->hw.ax.base = 0;
return (0);
}
cs->hw.ax.isac_adr = cs->hw.ax.base + PO_OFFSET;
cs->hw.ax.jade_adr = cs->hw.ax.base + PO_OFFSET;
cs->hw.ax.isac_ale = GCS_1;
cs->hw.ax.jade_ale = GCS_3;
#else
printk(KERN_WARNING "HiSax: %s: NO_PCI_BIOS\n", CardType[card->typ]);
printk(KERN_WARNING "HiSax: %s: unable to configure\n", CardType[card->typ]);
return (0);
#endif /* CONFIG_PCI */
printk(KERN_INFO "HiSax: %s: Card configured at 0x%lX IRQ %d\n",
CardType[card->typ], cs->hw.ax.base, cs->irq);
setup_isac(cs);
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->BC_Read_Reg = &ReadJADE;
cs->BC_Write_Reg = &WriteJADE;
cs->BC_Send_Data = &jade_fill_fifo;
cs->cardmsg = &BKM_card_msg;
cs->irq_func = &bkm_interrupt;
cs->irq_flags |= SA_SHIRQ;
ISACVersion(cs, "Telekom A4T:");
/* Jade version */
JadeVersion(cs, "Telekom A4T:");
return (1);
}
开发者ID:jameshilliard，项目名称:actiontec_opensrc_mi424wr-rev-i_fw-40-21-10-2，代码行数:84，代码来源:bkm_a4t.c
示例9: setup_diva
//.........这里部分代码省略.........
return (0);
#endif /* CONFIG_PCI */
if ((cs->subtyp == DIVA_IPAC_PCI) ||
(cs->subtyp == DIVA_IPACX_PCI) ) {
cs->hw.diva.ctrl = 0;
cs->hw.diva.isac = 0;
cs->hw.diva.hscx = 0;
cs->hw.diva.isac_adr = 0;
cs->hw.diva.hscx_adr = 0;
test_and_set_bit(HW_IPAC, &cs->HW_Flags);
bytecnt = 0;
} else {
cs->hw.diva.ctrl = cs->hw.diva.cfg_reg + DIVA_PCI_CTRL;
cs->hw.diva.isac = cs->hw.diva.cfg_reg + DIVA_PCI_ISAC_DATA;
cs->hw.diva.hscx = cs->hw.diva.cfg_reg + DIVA_HSCX_DATA;
cs->hw.diva.isac_adr = cs->hw.diva.cfg_reg + DIVA_PCI_ISAC_ADR;
cs->hw.diva.hscx_adr = cs->hw.diva.cfg_reg + DIVA_HSCX_ADR;
bytecnt = 32;
}
}
ready:
printk(KERN_INFO
"Diva: %s card configured at %#lx IRQ %d\n",
(cs->subtyp == DIVA_PCI) ? "PCI" :
(cs->subtyp == DIVA_ISA) ? "ISA" :
(cs->subtyp == DIVA_IPAC_ISA) ? "IPAC ISA" :
(cs->subtyp == DIVA_IPAC_PCI) ? "IPAC PCI" : "IPACX PCI",
cs->hw.diva.cfg_reg, cs->irq);
if ((cs->subtyp == DIVA_IPAC_PCI) ||
(cs->subtyp == DIVA_IPACX_PCI) ||
(cs->subtyp == DIVA_PCI) )
printk(KERN_INFO "Diva: %s space at %#lx\n",
(cs->subtyp == DIVA_PCI) ? "PCI" :
(cs->subtyp == DIVA_IPAC_PCI) ? "IPAC PCI" : "IPACX PCI",
cs->hw.diva.pci_cfg);
if ((cs->subtyp != DIVA_IPAC_PCI) &&
(cs->subtyp != DIVA_IPACX_PCI) ) {
if (!request_region(cs->hw.diva.cfg_reg, bytecnt, "diva isdn")) {
printk(KERN_WARNING
"HiSax: %s config port %lx-%lx already in use\n",
CardType[card->typ],
cs->hw.diva.cfg_reg,
cs->hw.diva.cfg_reg + bytecnt);
return (0);
}
}
cs->BC_Read_Reg = &ReadHSCX;
cs->BC_Write_Reg = &WriteHSCX;
cs->BC_Send_Data = &hscx_fill_fifo;
cs->cardmsg = &Diva_card_msg;
setup_isac(cs);
if (cs->subtyp == DIVA_IPAC_ISA) {
cs->readisac = &ReadISAC_IPAC;
cs->writeisac = &WriteISAC_IPAC;
cs->readisacfifo = &ReadISACfifo_IPAC;
cs->writeisacfifo = &WriteISACfifo_IPAC;
cs->irq_func = &diva_irq_ipac_isa;
val = readreg(cs->hw.diva.isac_adr, cs->hw.diva.isac, IPAC_ID);
printk(KERN_INFO "Diva: IPAC version %x\n", val);
} else if (cs->subtyp == DIVA_IPAC_PCI) {
cs->readisac = &MemReadISAC_IPAC;
cs->writeisac = &MemWriteISAC_IPAC;
cs->readisacfifo = &MemReadISACfifo_IPAC;
cs->writeisacfifo = &MemWriteISACfifo_IPAC;
cs->BC_Read_Reg = &MemReadHSCX;
cs->BC_Write_Reg = &MemWriteHSCX;
cs->BC_Send_Data = &Memhscx_fill_fifo;
cs->irq_func = &diva_irq_ipac_pci;
val = memreadreg(cs->hw.diva.cfg_reg, IPAC_ID);
printk(KERN_INFO "Diva: IPAC version %x\n", val);
} else if (cs->subtyp == DIVA_IPACX_PCI) {
cs->readisac = &MemReadISAC_IPACX;
cs->writeisac = &MemWriteISAC_IPACX;
cs->readisacfifo = &MemReadISACfifo_IPACX;
cs->writeisacfifo = &MemWriteISACfifo_IPACX;
cs->BC_Read_Reg = &MemReadHSCX_IPACX;
cs->BC_Write_Reg = &MemWriteHSCX_IPACX;
cs->BC_Send_Data = NULL; // function located in ipacx module
cs->irq_func = &diva_irq_ipacx_pci;
printk(KERN_INFO "Diva: IPACX Design Id: %x\n",
MemReadISAC_IPACX(cs, IPACX_ID) &0x3F);
} else { /* DIVA 2.0 */
cs->hw.diva.tl.function = (void *) diva_led_handler;
cs->hw.diva.tl.data = (long) cs;
init_timer(&cs->hw.diva.tl);
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->irq_func = &diva_interrupt;
ISACVersion(cs, "Diva:");
if (HscxVersion(cs, "Diva:")) {
printk(KERN_WARNING
"Diva: wrong HSCX versions check IO address\n");
release_io_diva(cs);
return (0);
}
}
return (1);
}
开发者ID:jameshilliard，项目名称:actiontec_opensrc_mi424wr-rev-e-f_fw-20-10-7-5，代码行数:101，代码来源:diva.c
示例10: setup_telespci
int __devinit
setup_telespci(struct IsdnCard *card)
{
struct IsdnCardState *cs = card->cs;
char tmp[64];
#ifdef __BIG_ENDIAN
#error "not running on big endian machines now"
#endif
strcpy(tmp, telespci_revision);
;
if (cs->typ != ISDN_CTYPE_TELESPCI)
return (0);
if ((dev_tel = hisax_find_pci_device (PCI_VENDOR_ID_ZORAN, PCI_DEVICE_ID_ZORAN_36120, dev_tel))) {
if (pci_enable_device(dev_tel))
return(0);
cs->irq = dev_tel->irq;
if (!cs->irq) {
;
return(0);
}
cs->hw.teles0.membase = ioremap(pci_resource_start(dev_tel, 0),
PAGE_SIZE);
// printk(KERN_INFO "Found: Zoran, base-address: 0x%llx, irq: 0x%x\n",
// (unsigned long long)pci_resource_start(dev_tel, 0),
;
} else {
;
return(0);
}
/* Initialize Zoran PCI controller */
writel(0x00000000, cs->hw.teles0.membase + 0x28);
writel(0x01000000, cs->hw.teles0.membase + 0x28);
writel(0x01000000, cs->hw.teles0.membase + 0x28);
writel(0x7BFFFFFF, cs->hw.teles0.membase + 0x2C);
writel(0x70000000, cs->hw.teles0.membase + 0x3C);
writel(0x61000000, cs->hw.teles0.membase + 0x40);
/* writel(0x00800000, cs->hw.teles0.membase + 0x200); */
// printk(KERN_INFO
// "HiSax: Teles PCI config irq:%d mem:%p\n",
// cs->irq,
;
setup_isac(cs);
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->BC_Read_Reg = &ReadHSCX;
cs->BC_Write_Reg = &WriteHSCX;
cs->BC_Send_Data = &hscx_fill_fifo;
cs->cardmsg = &TelesPCI_card_msg;
cs->irq_func = &telespci_interrupt;
cs->irq_flags |= IRQF_SHARED;
ISACVersion(cs, "TelesPCI:");
if (HscxVersion(cs, "TelesPCI:")) {
// printk(KERN_WARNING
;
release_io_telespci(cs);
return (0);
}
return (1);
}
开发者ID:rrowicki，项目名称:Chrono_Kernel-1，代码行数:67，代码来源:telespci.c
示例11: setup_avm_a1
//.........这里部分代码省略.........
if (!request_region(cs->hw.avm.isacfifo, 1, "HiSax isac fifo")) {
printk(KERN_WARNING
"HiSax: %s isac fifo port %x already in use\n",
CardType[cs->typ],
cs->hw.avm.isacfifo);
release_ioregs(cs, 1);
return (0);
}
if (!request_region(cs->hw.avm.hscx[0] + 32, 32, "HiSax hscx A")) {
printk(KERN_WARNING
"HiSax: %s hscx A ports %x-%x already in use\n",
CardType[cs->typ],
cs->hw.avm.hscx[0] + 32,
cs->hw.avm.hscx[0] + 64);
release_ioregs(cs, 3);
return (0);
}
if (!request_region(cs->hw.avm.hscxfifo[0], 1, "HiSax hscx A fifo")) {
printk(KERN_WARNING
"HiSax: %s hscx A fifo port %x already in use\n",
CardType[cs->typ],
cs->hw.avm.hscxfifo[0]);
release_ioregs(cs, 7);
return (0);
}
if (!request_region(cs->hw.avm.hscx[1] + 32, 32, "HiSax hscx B")) {
printk(KERN_WARNING
"HiSax: %s hscx B ports %x-%x already in use\n",
CardType[cs->typ],
cs->hw.avm.hscx[1] + 32,
cs->hw.avm.hscx[1] + 64);
release_ioregs(cs, 0xf);
return (0);
}
if (!request_region(cs->hw.avm.hscxfifo[1], 1, "HiSax hscx B fifo")) {
printk(KERN_WARNING
"HiSax: %s hscx B fifo port %x already in use\n",
CardType[cs->typ],
cs->hw.avm.hscxfifo[1]);
release_ioregs(cs, 0x1f);
return (0);
}
byteout(cs->hw.avm.cfg_reg, 0x0);
HZDELAY(HZ / 5 + 1);
byteout(cs->hw.avm.cfg_reg, 0x1);
HZDELAY(HZ / 5 + 1);
byteout(cs->hw.avm.cfg_reg, 0x0);
HZDELAY(HZ / 5 + 1);
val = cs->irq;
if (val == 9)
val = 2;
byteout(cs->hw.avm.cfg_reg + 1, val);
HZDELAY(HZ / 5 + 1);
byteout(cs->hw.avm.cfg_reg, 0x0);
HZDELAY(HZ / 5 + 1);
val = bytein(cs->hw.avm.cfg_reg);
printk(KERN_INFO "AVM A1: Byte at %x is %x\n",
cs->hw.avm.cfg_reg, val);
val = bytein(cs->hw.avm.cfg_reg + 3);
printk(KERN_INFO "AVM A1: Byte at %x is %x\n",
cs->hw.avm.cfg_reg + 3, val);
val = bytein(cs->hw.avm.cfg_reg + 2);
printk(KERN_INFO "AVM A1: Byte at %x is %x\n",
cs->hw.avm.cfg_reg + 2, val);
val = bytein(cs->hw.avm.cfg_reg);
printk(KERN_INFO "AVM A1: Byte at %x is %x\n",
cs->hw.avm.cfg_reg, val);
printk(KERN_INFO
"HiSax: %s config irq:%d cfg:0x%X\n",
CardType[cs->typ], cs->irq,
cs->hw.avm.cfg_reg);
printk(KERN_INFO
"HiSax: isac:0x%X/0x%X\n",
cs->hw.avm.isac + 32, cs->hw.avm.isacfifo);
printk(KERN_INFO
"HiSax: hscx A:0x%X/0x%X hscx B:0x%X/0x%X\n",
cs->hw.avm.hscx[0] + 32, cs->hw.avm.hscxfifo[0],
cs->hw.avm.hscx[1] + 32, cs->hw.avm.hscxfifo[1]);
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->BC_Read_Reg = &ReadHSCX;
cs->BC_Write_Reg = &WriteHSCX;
cs->BC_Send_Data = &hscx_fill_fifo;
setup_isac(cs);
cs->cardmsg = &AVM_card_msg;
cs->irq_func = &avm_a1_interrupt;
ISACVersion(cs, "AVM A1:");
if (HscxVersion(cs, "AVM A1:")) {
printk(KERN_WARNING
"AVM A1: wrong HSCX versions check IO address\n");
release_ioregs(cs, 0x3f);
return (0);
}
return (1);
}
开发者ID:robacklin，项目名称:ts7800，代码行数:101，代码来源:avm_a1.c
示例12: setup_asuscom
int __init
setup_asuscom(struct IsdnCard *card)
{
int bytecnt;
struct IsdnCardState *cs = card->cs;
u_char val;
char tmp[64];
strcpy(tmp, Asuscom_revision);
printk(KERN_INFO "HiSax: Asuscom ISDNLink driver Rev. %s\n", HiSax_getrev(tmp));
if (cs->typ != ISDN_CTYPE_ASUSCOM)
return (0);
#ifdef __ISAPNP__
if (!card->para[1] && isapnp_present()) {
struct pnp_dev *pnp_d;
while(ipid->card_vendor) {
if ((pnp_c = pnp_find_card(ipid->card_vendor,
ipid->card_device, pnp_c))) {
pnp_d = NULL;
if ((pnp_d = pnp_find_dev(pnp_c,
ipid->vendor, ipid->function, pnp_d))) {
int err;
printk(KERN_INFO "HiSax: %s detected\n",
(char *)ipid->driver_data);
pnp_disable_dev(pnp_d);
err = pnp_activate_dev(pnp_d);
if (err<0) {
printk(KERN_WARNING "%s: pnp_activate_dev ret(%d)\n",
__FUNCTION__, err);
return(0);
}
card->para[1] = pnp_port_start(pnp_d, 0);
card->para[0] = pnp_irq(pnp_d, 0);
if (!card->para[0] || !card->para[1]) {
printk(KERN_ERR "AsusPnP:some resources are missing %ld/%lx\n",
card->para[0], card->para[1]);
pnp_disable_dev(pnp_d);
return(0);
}
break;
} else {
printk(KERN_ERR "AsusPnP: PnP error card found, no device\n");
}
}
ipid++;
pnp_c = NULL;
}
if (!ipid->card_vendor) {
printk(KERN_INFO "AsusPnP: no ISAPnP card found\n");
return(0);
}
}
#endif
bytecnt = 8;
cs->hw.asus.cfg_reg = card->para[1];
cs->irq = card->para[0];
if (!request_region(cs->hw.asus.cfg_reg, bytecnt, "asuscom isdn")) {
printk(KERN_WARNING
"HiSax: %s config port %x-%x already in use\n",
CardType[card->typ],
cs->hw.asus.cfg_reg,
cs->hw.asus.cfg_reg + bytecnt);
return (0);
}
printk(KERN_INFO "ISDNLink: defined at 0x%x IRQ %d\n",
cs->hw.asus.cfg_reg, cs->irq);
setup_isac(cs);
cs->BC_Read_Reg = &ReadHSCX;
cs->BC_Write_Reg = &WriteHSCX;
cs->BC_Send_Data = &hscx_fill_fifo;
cs->cardmsg = &Asus_card_msg;
val = readreg(cs->hw.asus.cfg_reg + ASUS_IPAC_ALE,
cs->hw.asus.cfg_reg + ASUS_IPAC_DATA, IPAC_ID);
if ((val == 1) || (val == 2)) {
cs->subtyp = ASUS_IPAC;
cs->hw.asus.adr = cs->hw.asus.cfg_reg + ASUS_IPAC_ALE;
cs->hw.asus.isac = cs->hw.asus.cfg_reg + ASUS_IPAC_DATA;
cs->hw.asus.hscx = cs->hw.asus.cfg_reg + ASUS_IPAC_DATA;
test_and_set_bit(HW_IPAC, &cs->HW_Flags);
cs->readisac = &ReadISAC_IPAC;
cs->writeisac = &WriteISAC_IPAC;
cs->readisacfifo = &ReadISACfifo_IPAC;
cs->writeisacfifo = &WriteISACfifo_IPAC;
cs->irq_func = &asuscom_interrupt_ipac;
printk(KERN_INFO "Asus: IPAC version %x\n", val);
} else {
cs->subtyp = ASUS_ISACHSCX;
cs->hw.asus.adr = cs->hw.asus.cfg_reg + ASUS_ADR;
cs->hw.asus.isac = cs->hw.asus.cfg_reg + ASUS_ISAC;
cs->hw.asus.hscx = cs->hw.asus.cfg_reg + ASUS_HSCX;
cs->hw.asus.u7 = cs->hw.asus.cfg_reg + ASUS_CTRL_U7;
cs->hw.asus.pots = cs->hw.asus.cfg_reg + ASUS_CTRL_POTS;
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->irq_func = &asuscom_interrupt;
ISACVersion(cs, "ISDNLink:");
if (HscxVersion(cs, "ISDNLink:")) {
//.........这里部分代码省略.........
开发者ID:BackupTheBerlios，项目名称:tew632-brp-svn，代码行数:101，代码来源:asuscom.c
示例13: setup_niccy
//.........这里部分代码省略.........
cs->hw.niccy.hscx_ale = card->para[2] + HSCX_PNP;
cs->hw.niccy.cfg_reg = 0;
cs->subtyp = NICCY_PNP;
cs->irq = card->para[0];
if (!request_region(cs->hw.niccy.isac, 2, "niccy data")) {
printk(KERN_WARNING
"HiSax: %s data port %x-%x already in use\n",
CardType[card->typ],
cs->hw.niccy.isac,
cs->hw.niccy.isac + 1);
return (0);
}
if (!request_region(cs->hw.niccy.isac_ale, 2, "niccy addr")) {
printk(KERN_WARNING
"HiSax: %s address port %x-%x already in use\n",
CardType[card->typ],
cs->hw.niccy.isac_ale,
cs->hw.niccy.isac_ale + 1);
release_region(cs->hw.niccy.isac, 2);
return (0);
}
} else {
#ifdef CONFIG_PCI
u_int pci_ioaddr;
cs->subtyp = 0;
if ((niccy_dev = pci_find_device(PCI_VENDOR_ID_SATSAGEM,
PCI_DEVICE_ID_SATSAGEM_NICCY, niccy_dev))) {
if (pci_enable_device(niccy_dev))
return(0);
/* get IRQ */
if (!niccy_dev->irq) {
printk(KERN_WARNING "Niccy: No IRQ for PCI card found\n");
return(0);
}
cs->irq = niccy_dev->irq;
cs->hw.niccy.cfg_reg = pci_resource_start(niccy_dev, 0);
if (!cs->hw.niccy.cfg_reg) {
printk(KERN_WARNING "Niccy: No IO-Adr for PCI cfg found\n");
return(0);
}
pci_ioaddr = pci_resource_start(niccy_dev, 1);
if (!pci_ioaddr) {
printk(KERN_WARNING "Niccy: No IO-Adr for PCI card found\n");
return(0);
}
cs->subtyp = NICCY_PCI;
} else {
printk(KERN_WARNING "Niccy: No PCI card found\n");
return(0);
}
cs->irq_flags |= SA_SHIRQ;
cs->hw.niccy.isac = pci_ioaddr + ISAC_PCI_DATA;
cs->hw.niccy.isac_ale = pci_ioaddr + ISAC_PCI_ADDR;
cs->hw.niccy.hscx = pci_ioaddr + HSCX_PCI_DATA;
cs->hw.niccy.hscx_ale = pci_ioaddr + HSCX_PCI_ADDR;
if (!request_region(cs->hw.niccy.isac, 4, "niccy")) {
printk(KERN_WARNING
"HiSax: %s data port %x-%x already in use\n",
CardType[card->typ],
cs->hw.niccy.isac,
cs->hw.niccy.isac + 4);
return (0);
}
if (!request_region(cs->hw.niccy.cfg_reg, 0x40, "niccy pci")) {
printk(KERN_WARNING
"HiSax: %s pci port %x-%x already in use\n",
CardType[card->typ],
cs->hw.niccy.cfg_reg,
cs->hw.niccy.cfg_reg + 0x40);
release_region(cs->hw.niccy.isac, 4);
return (0);
}
#else
printk(KERN_WARNING "Niccy: io0 0 and NO_PCI_BIOS\n");
printk(KERN_WARNING "Niccy: unable to config NICCY PCI\n");
return (0);
#endif /* CONFIG_PCI */
}
printk(KERN_INFO "HiSax: %s %s config irq:%d data:0x%X ale:0x%X\n",
CardType[cs->typ], (cs->subtyp==1) ? "PnP":"PCI",
cs->irq, cs->hw.niccy.isac, cs->hw.niccy.isac_ale);
setup_isac(cs);
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->BC_Read_Reg = &ReadHSCX;
cs->BC_Write_Reg = &WriteHSCX;
cs->BC_Send_Data = &hscx_fill_fifo;
cs->cardmsg = &niccy_card_msg;
cs->irq_func = &niccy_interrupt;
ISACVersion(cs, "Niccy:");
if (HscxVersion(cs, "Niccy:")) {
printk(KERN_WARNING
"Niccy: wrong HSCX versions check IO address\n");
release_io_niccy(cs);
return (0);
}
return (1);
}
开发者ID:BackupTheBerlios，项目名称:tew632-brp-svn，代码行数:101，代码来源:niccy.c
示例14: setup_ix1micro
int __devinit
setup_ix1micro(struct IsdnCard *card)
{
struct IsdnCardState *cs = card->cs;
char tmp[64];
strcpy(tmp, ix1_revision);
printk(KERN_INFO "HiSax: ITK IX1 driver Rev. %s\n", HiSax_getrev(tmp));
if (cs->typ != ISDN_CTYPE_IX1MICROR2)
return (0);
#ifdef __ISAPNP__
if (!card->para[1] && isapnp_present()) {
struct pnp_dev *pnp_d;
while(ipid->card_vendor) {
if ((pnp_c = pnp_find_card(ipid->card_vendor,
ipid->card_device, pnp_c))) {
pnp_d = NULL;
if ((pnp_d = pnp_find_dev(pnp_c,
ipid->vendor, ipid->function, pnp_d))) {
int err;
printk(KERN_INFO "HiSax: %s detected\n",
(char *)ipid->driver_data);
pnp_disable_dev(pnp_d);
err = pnp_activate_dev(pnp_d);
if (err<0) {
printk(KERN_WARNING "%s: pnp_activate_dev ret(%d)\n",
__FUNCTION__, err);
return(0);
}
card->para[1] = pnp_port_start(pnp_d, 0);
card->para[0] = pnp_irq(pnp_d, 0);
if (!card->para[0] || !card->para[1]) {
printk(KERN_ERR "ITK PnP:some resources are missing %ld/%lx\n",
card->para[0], card->para[1]);
pnp_disable_dev(pnp_d);
return(0);
}
break;
} else {
printk(KERN_ERR "ITK PnP: PnP error card found, no device\n");
}
}
ipid++;
pnp_c = NULL;
}
if (!ipid->card_vendor) {
printk(KERN_INFO "ITK PnP: no ISAPnP card found\n");
return(0);
}
}
#endif
/* IO-Ports */
cs->hw.ix1.isac_ale = card->para[1] + ISAC_COMMAND_OFFSET;
cs->hw.ix1.hscx_ale = card->para[1] + HSCX_COMMAND_OFFSET;
cs->hw.ix1.isac = card->para[1] + ISAC_DATA_OFFSET;
cs->hw.ix1.hscx = card->para[1] + HSCX_DATA_OFFSET;
cs->hw.ix1.cfg_reg = card->para[1];
cs->irq = card->para[0];
if (cs->hw.ix1.cfg_reg) {
if (!request_region(cs->hw.ix1.cfg_reg, 4, "ix1micro cfg")) {
printk(KERN_WARNING
"HiSax: %s config port %x-%x already in use\n",
CardType[card->typ],
cs->hw.ix1.cfg_reg,
cs->hw.ix1.cfg_reg + 4);
return (0);
}
}
printk(KERN_INFO "HiSax: %s config irq:%d io:0x%X\n",
CardType[cs->typ], cs->irq, cs->hw.ix1.cfg_reg);
setup_isac(cs);
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->BC_Read_Reg = &ReadHSCX;
cs->BC_Write_Reg = &WriteHSCX;
cs->BC_Send_Data = &hscx_fill_fifo;
cs->cardmsg = &ix1_card_msg;
cs->irq_func = &ix1micro_interrupt;
ISACVersion(cs, "ix1-Micro:");
if (HscxVersion(cs, "ix1-Micro:")) {
printk(KERN_WARNING
"ix1-Micro: wrong HSCX versions check IO address\n");
release_io_ix1micro(cs);
return (0);
}
return (1);
}
开发者ID:ManiacTwister，项目名称:linux-hnd，代码行数:91，代码来源:ix1_micro.c
示例15: setup_TeleInt
int __devinit
setup_TeleInt(struct IsdnCard *card)
{
struct IsdnCardState *cs = card->cs;
char tmp[64];
strcpy(tmp, TeleInt_revision);
printk(KERN_INFO "HiSax: TeleInt driver Rev. %s\n", HiSax_getrev(tmp));
if (cs->typ != ISDN_CTYPE_TELEINT)
return (0);
cs->hw.hfc.addr = card->para[1] & 0x3fe;
cs->irq = card->para[0];
cs->hw.hfc.cirm = HFC_CIRM;
cs->hw.hfc.isac_spcr = 0x00;
cs->hw.hfc.cip = 0;
cs->hw.hfc.ctmt = HFC_CTMT | HFC_CLTIMER;
cs->bcs[0].hw.hfc.send = NULL;
cs->bcs[1].hw.hfc.send = NULL;
cs->hw.hfc.fifosize = 7 * 1024 + 512;
cs->hw.hfc.timer.function = (void *) TeleInt_Timer;
cs->hw.hfc.timer.data = (long) cs;
init_timer(&cs->hw.hfc.timer);
if (!request_region(cs->hw.hfc.addr, 2, "TeleInt isdn")) {
printk(KERN_WARNING
"HiSax: TeleInt config port %x-%x already in use\n",
cs->hw.hfc.addr,
cs->hw.hfc.addr + 2);
return (0);
}
/* HW IO = IO */
byteout(cs->hw.hfc.addr, cs->hw.hfc.addr & 0xff);
byteout(cs->hw.hfc.addr | 1, ((cs->hw.hfc.addr & 0x300) >> 8) | 0x54);
switch (cs->irq) {
case 3:
cs->hw.hfc.cirm |= HFC_INTA;
break;
case 4:
cs->hw.hfc.cirm |= HFC_INTB;
break;
case 5:
cs->hw.hfc.cirm |= HFC_INTC;
break;
case 7:
cs->hw.hfc.cirm |= HFC_INTD;
break;
case 10:
cs->hw.hfc.cirm |= HFC_INTE;
break;
case 11:
cs->hw.hfc.cirm |= HFC_INTF;
break;
default:
printk(KERN_WARNING "TeleInt: wrong IRQ\n");
release_io_TeleInt(cs);
return (0);
}
byteout(cs->hw.hfc.addr | 1, cs->hw.hfc.cirm);
byteout(cs->hw.hfc.addr | 1, cs->hw.hfc.ctmt);
printk(KERN_INFO "TeleInt: defined at 0x%x IRQ %d\n",
cs->hw.hfc.addr, cs->irq);
setup_isac(cs);
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
cs->BC_Read_Reg = &ReadHFC;
cs->BC_Write_Reg = &WriteHFC;
cs->cardmsg = &TeleInt_card_msg;
cs->irq_func = &TeleInt_interrupt;
ISACVersion(cs, "TeleInt:");
return (1);
}
开发者ID:274914765，项目名称:C，代码行数:75，代码来源:teleint.c
示例16: setup_sedlbauer
//.........这里部分代码省略.........
cs->BC_Send_Data = &hscx_fill_fifo;
cs->cardmsg = &Sedl_card_msg;
/*
* testing ISA and PCMCIA Cards for IPAC, default is ISAC
* do not test for PCI card, because ports are different
* and PCI card uses only IPAC (for the moment)
*/
if (cs->hw.sedl.bus != SEDL_BUS_PCI) {
val = readreg(cs->hw.sedl.cfg_reg + SEDL_IPAC_ANY_ADR,
cs->hw.sedl.cfg_reg + SEDL_IPAC_ANY_IPAC, IPAC_ID);
printk(KERN_DEBUG "Sedlbauer: testing IPAC version %x\n", val);
if ((val == 1) || (val == 2)) {
/* IPAC */
cs->subtyp = SEDL_SPEED_WIN2_PC104;
if (cs->hw.sedl.bus == SEDL_BUS_PCMCIA) {
cs->subtyp = SEDL_SPEED_STAR2;
}
cs->hw.sedl.chip = SEDL_CHIP_IPAC;
} else {
/* ISAC_HSCX oder ISAC_ISAR */
if (cs->hw.sedl.chip == SEDL_CHIP_TEST) {
cs->hw.sedl.chip = SEDL_CHIP_ISAC_HSCX;
}
}
}
/*
* hw.sedl.chip is now properly set
*/
printk(KERN_INFO "Sedlbauer: %s detected\n",
Sedlbauer_Types[cs->subtyp]);
setup_isac(cs);
if (cs->hw.sedl.chip == SEDL_CHIP_IPAC) {
if (cs->hw.sedl.bus == SEDL_BUS_PCI) {
cs->hw.sedl.adr = cs->hw.sedl.cfg_reg + SEDL_IPAC_PCI_ADR;
cs->hw.sedl.isac = cs->hw.sedl.cfg_reg + SEDL_IPAC_PCI_IPAC;
cs->hw.sedl.hscx = cs->hw.sedl.cfg_reg + SEDL_IPAC_PCI_IPAC;
} else {
cs->hw.sedl.adr = cs->hw.sedl.cfg_reg + SEDL_IPAC_ANY_ADR;
cs->hw.sedl.isac = cs->hw.sedl.cfg_reg + SEDL_IPAC_ANY_IPAC;
cs->hw.sedl.hscx = cs->hw.sedl.cfg_reg + SEDL_IPAC_ANY_IPAC;
}
test_and_set_bit(HW_IPAC, &cs->HW_Flags);
cs->readisac = &ReadISAC_IPAC;
cs->writeisac = &WriteISAC_IPAC;
cs->readisacfifo = &ReadISACfifo_IPAC;
cs->writeisacfifo = &WriteISACfifo_IPAC;
cs->irq_func = &sedlbauer_interrupt_ipac;
val = readreg(cs->hw.sedl.adr, cs->hw.sedl.isac, IPAC_ID);
printk(KERN_INFO "Sedlbauer: IPAC version %x\n", val);
} else {
/* ISAC_HSCX oder ISAC_ISAR */
cs->readisac = &ReadISAC;
cs->writeisac = &WriteISAC;
cs->readisacfifo = &ReadISACfifo;
cs->writeisacfifo = &WriteISACfifo;
if (cs->hw.sedl.chip == SEDL_CHIP_ISAC_ISAR) {
if (cs->hw.sedl.bus == SEDL_BUS_PCI) {
cs->hw.sedl.adr = cs->hw.sedl.cfg_reg +
SEDL_ISAR_PCI_ADR;
cs->hw.sedl.isac = cs->hw.sedl.cfg_reg +
SEDL_ISAR_PCI_ISAC;
cs->hw.sedl.hscx = cs->hw.sedl.cfg_reg +
SEDL_ISAR_PCI_ISAR;
开发者ID:458941968，项目名称:mini2440-kernel-2.6.29，代码行数:67，代码来源:sedlbauer.c
-
六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期
阅读：18175|2023-10-27
-
今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知
阅读：9641|2022-11-06
-
今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道
阅读：8166|2022-11-06
-
今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要
阅读：8542|2022-11-06
-
我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多
阅读：8444|2022-11-06
-
今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不
阅读：9368|2022-11-06
-
电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很
阅读：8415|2022-11-06
-
我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法
阅读：7852|2022-11-06
-
今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win
阅读：8399|2022-11-06
-
今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎
阅读：7391|2022-11-06
|
客服电话
APP下载
官方微信
请发表评论