C++ CR_CHAN函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中CR_CHAN函数的典型用法代码示例。如果您正苦于以下问题：C++ CR_CHAN函数的具体用法？C++ CR_CHAN怎么用？C++ CR_CHAN使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了CR_CHAN函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: dmm32at_ai_check_chanlist

static int dmm32at_ai_check_chanlist(struct comedi_device *dev,
				     struct comedi_subdevice *s,
				     struct comedi_cmd *cmd)
{
	unsigned int chan0 = CR_CHAN(cmd->chanlist[0]);
	unsigned int range0 = CR_RANGE(cmd->chanlist[0]);
	int i;

	for (i = 1; i < cmd->chanlist_len; i++) {
		unsigned int chan = CR_CHAN(cmd->chanlist[i]);
		unsigned int range = CR_RANGE(cmd->chanlist[i]);

		if (chan != (chan0 + i) % s->n_chan) {
			dev_dbg(dev->class_dev,
				"entries in chanlist must be consecutive channels, counting upwards\n");
			return -EINVAL;
		}
		if (range != range0) {
			dev_dbg(dev->class_dev,
				"entries in chanlist must all have the same gain\n");
			return -EINVAL;
		}
	}

	return 0;
}

开发者ID:AlexShiLucky，项目名称:linux，代码行数:26，代码来源:dmm32at.c

示例2: ni_m_series_set_second_gate

static int ni_m_series_set_second_gate(struct ni_gpct *counter,
	lsampl_t gate_source)
{
	struct ni_gpct_device *counter_dev = counter->counter_dev;
	const unsigned second_gate_reg =
		NITIO_Gi_Second_Gate_Reg(counter->counter_index);
	const unsigned selected_second_gate = CR_CHAN(gate_source);
	/* bits of second_gate that may be meaningful to second gate register */
	static const unsigned selected_second_gate_mask = 0x1f;
	unsigned ni_m_series_second_gate_select;

	/* FIXME: We don't know what the m-series second gate codes are, so we'll just pass
	   the bits through for now. */
	switch (selected_second_gate) {
	default:
		ni_m_series_second_gate_select =
			selected_second_gate & selected_second_gate_mask;
		break;
	};
	counter_dev->regs[second_gate_reg] |= Gi_Second_Gate_Mode_Bit;
	counter_dev->regs[second_gate_reg] &= ~Gi_Second_Gate_Select_Mask;
	counter_dev->regs[second_gate_reg] |=
		Gi_Second_Gate_Select_Bits(ni_m_series_second_gate_select);
	write_register(counter, counter_dev->regs[second_gate_reg],
		second_gate_reg);
	return 0;
}

开发者ID:jbetten，项目名称:rtxi，代码行数:27，代码来源:ni_tio.c

示例3: multiq3_ai_insn_read

static int multiq3_ai_insn_read(struct comedi_device *dev,
				struct comedi_subdevice *s,
				struct comedi_insn *insn, unsigned int *data)
{
	int n;
	int chan;
	unsigned int hi, lo;
	int ret;

	chan = CR_CHAN(insn->chanspec);
	outw(MULTIQ3_CONTROL_MUST | MULTIQ3_AD_MUX_EN | (chan << 3),
	     dev->iobase + MULTIQ3_CONTROL);

	ret = comedi_timeout(dev, s, insn, multiq3_ai_status,
			     MULTIQ3_STATUS_EOC);
	if (ret)
		return ret;

	for (n = 0; n < insn->n; n++) {
		outw(0, dev->iobase + MULTIQ3_AD_CS);

		ret = comedi_timeout(dev, s, insn, multiq3_ai_status,
				     MULTIQ3_STATUS_EOC_I);
		if (ret)
			return ret;

		hi = inb(dev->iobase + MULTIQ3_AD_CS);
		lo = inb(dev->iobase + MULTIQ3_AD_CS);
		data[n] = (((hi << 8) | lo) + 0x1000) & 0x1fff;
	}

	return n;
}

开发者ID:AkyZero，项目名称:wrapfs-latest，代码行数:33，代码来源:multiq3.c

示例4: usbduxsigma_ao_insn_write

static int usbduxsigma_ao_insn_write(struct comedi_device *dev,
				     struct comedi_subdevice *s,
				     struct comedi_insn *insn,
				     unsigned int *data)
{
	struct usbduxsigma_private *devpriv = dev->private;
	unsigned int chan = CR_CHAN(insn->chanspec);
	int ret;
	int i;

	down(&devpriv->sem);
	if (devpriv->ao_cmd_running) {
		up(&devpriv->sem);
		return -EBUSY;
	}

	for (i = 0; i < insn->n; i++) {
		devpriv->dux_commands[1] = 1;		/* num channels */
		devpriv->dux_commands[2] = data[i];	/* value */
		devpriv->dux_commands[3] = chan;	/* channel number */
		ret = usbbuxsigma_send_cmd(dev, USBDUXSIGMA_DA_CMD);
		if (ret < 0) {
			up(&devpriv->sem);
			return ret;
		}
		s->readback[chan] = data[i];
	}
	up(&devpriv->sem);

	return insn->n;
}

开发者ID:3null，项目名称:linux，代码行数:31，代码来源:usbduxsigma.c

示例5: pci6208_ao_insn_write

static int pci6208_ao_insn_write(struct comedi_device *dev,
				 struct comedi_subdevice *s,
				 struct comedi_insn *insn,
				 unsigned int *data)
{
	unsigned int chan = CR_CHAN(insn->chanspec);
	unsigned int val = s->readback[chan];
	int ret;
	int i;

	for (i = 0; i < insn->n; i++) {
		val = data[i];

		/* D/A transfer rate is 2.2us */
		ret = comedi_timeout(dev, s, insn, pci6208_ao_eoc, 0);
		if (ret)
			return ret;

		/* the hardware expects two's complement values */
		outw(comedi_offset_munge(s, val),
		     dev->iobase + PCI6208_AO_CONTROL(chan));

		s->readback[chan] = val;
	}

	return insn->n;
}

开发者ID:020gzh，项目名称:linux，代码行数:27，代码来源:adl_pci6208.c

示例6: dt2815_ao_insn

static int dt2815_ao_insn(struct comedi_device *dev, struct comedi_subdevice *s,
			  struct comedi_insn *insn, unsigned int *data)
{
	struct dt2815_private *devpriv = dev->private;
	int i;
	int chan = CR_CHAN(insn->chanspec);
	unsigned int status;
	unsigned int lo, hi;

	for (i = 0; i < insn->n; i++) {
		lo = ((data[i] & 0x0f) << 4) | (chan << 1) | 0x01;
		hi = (data[i] & 0xff0) >> 4;

		status = dt2815_wait_for_status(dev, 0x00);
		if (status != 0) {
			dev_dbg(dev->class_dev,
				"failed to write low byte on %d reason %x\n",
				chan, status);
			return -EBUSY;
		}

		outb(lo, dev->iobase + DT2815_DATA);

		status = dt2815_wait_for_status(dev, 0x10);
		if (status != 0x10) {
			dev_dbg(dev->class_dev,
				"failed to write high byte on %d reason %x\n",
				chan, status);
			return -EBUSY;
		}
		devpriv->ao_readback[chan] = data[i];
	}
	return i;
}

开发者ID:IDM350，项目名称:linux，代码行数:34，代码来源:dt2815.c

示例7: dio200_start_intr

/*
 * Called to start acquisition for an 'INTERRUPT' subdevice.
 */
static int dio200_start_intr(struct comedi_device *dev,
			     struct comedi_subdevice *s)
{
	unsigned int n;
	unsigned isn_bits;
	const struct dio200_layout *layout = dio200_dev_layout(dev);
	struct dio200_subdev_intr *subpriv = s->private;
	struct comedi_cmd *cmd = &s->async->cmd;
	int retval = 0;

	if (cmd->stop_src == TRIG_COUNT && subpriv->stopcount == 0) {
		/* An empty acquisition! */
		s->async->events |= COMEDI_CB_EOA;
		subpriv->active = false;
		retval = 1;
	} else {
		/* Determine interrupt sources to enable. */
		isn_bits = 0;
		if (cmd->chanlist) {
			for (n = 0; n < cmd->chanlist_len; n++)
				isn_bits |= (1U << CR_CHAN(cmd->chanlist[n]));
		}
		isn_bits &= subpriv->valid_isns;
		/* Enable interrupt sources. */
		subpriv->enabled_isns = isn_bits;
		if (layout->has_int_sce)
			dio200_write8(dev, subpriv->ofs, isn_bits);
	}

	return retval;
}

开发者ID:mikuhatsune001，项目名称:linux2.6.32，代码行数:34，代码来源:amplc_dio200_common.c

示例8: dt2815_ao_insn

static int dt2815_ao_insn(struct comedi_device *dev, struct comedi_subdevice *s,
			  struct comedi_insn *insn, unsigned int *data)
{
	struct dt2815_private *devpriv = dev->private;
	int i;
	int chan = CR_CHAN(insn->chanspec);
	unsigned int lo, hi;
	int ret;

	for (i = 0; i < insn->n; i++) {
		lo = ((data[i] & 0x0f) << 4) | (chan << 1) | 0x01;
		hi = (data[i] & 0xff0) >> 4;

		ret = comedi_timeout(dev, s, insn, dt2815_ao_status, 0x00);
		if (ret)
			return ret;

		outb(lo, dev->iobase + DT2815_DATA);

		ret = comedi_timeout(dev, s, insn, dt2815_ao_status, 0x10);
		if (ret)
			return ret;

		devpriv->ao_readback[chan] = data[i];
	}
	return i;
}

开发者ID:AlexShiLucky，项目名称:linux，代码行数:27，代码来源:dt2815.c

示例9: pcl711_set_changain

static void pcl711_set_changain(struct comedi_device *dev, int chan)
{
	int chan_register;

	outb(CR_RANGE(chan), dev->iobase + PCL711_GAIN);

	chan_register = CR_CHAN(chan);

	if (this_board->is_8112) {

		/*
		 *  Set the correct channel.  The two channel banks are switched
		 *  using the mask value.
		 *  NB: To use differential channels, you should use
		 *  mask = 0x30, but I haven't written the support for this
		 *  yet. /JJ
		 */

		if (chan_register >= 8)
			chan_register = 0x20 | (chan_register & 0x7);
		else
			chan_register |= 0x10;
	} else {
		outb(chan_register, dev->iobase + PCL711_MUX);
	}
}

开发者ID:AllenWeb，项目名称:linux，代码行数:26，代码来源:pcl711.c

示例10: dmm32at_ao_insn_write

static int dmm32at_ao_insn_write(struct comedi_device *dev,
				 struct comedi_subdevice *s,
				 struct comedi_insn *insn,
				 unsigned int *data)
{
	unsigned int chan = CR_CHAN(insn->chanspec);
	int i;

	for (i = 0; i < insn->n; i++) {
		unsigned int val = data[i];
		int ret;

		/* write LSB then MSB + chan to load DAC */
		outb(val & 0xff, dev->iobase + DMM32AT_AO_LSB_REG);
		outb((val >> 8) | DMM32AT_AO_MSB_DACH(chan),
		     dev->iobase + DMM32AT_AO_MSB_REG);

		/* wait for circuit to settle */
		ret = comedi_timeout(dev, s, insn, dmm32at_ao_eoc, 0);
		if (ret)
			return ret;

		/* dummy read to update DAC */
		inb(dev->iobase + DMM32AT_AO_MSB_REG);

		s->readback[chan] = val;
	}

	return insn->n;
}

开发者ID:AlexShiLucky，项目名称:linux，代码行数:30，代码来源:dmm32at.c

示例11: cb_pcimdda_ao_insn_write

static int cb_pcimdda_ao_insn_write(struct comedi_device *dev,
				    struct comedi_subdevice *s,
				    struct comedi_insn *insn,
				    unsigned int *data)
{
	unsigned int chan = CR_CHAN(insn->chanspec);
	unsigned long offset = dev->iobase + PCIMDDA_DA_CHAN(chan);
	unsigned int val = s->readback[chan];
	int i;

	for (i = 0; i < insn->n; i++) {
		val = data[i];

		/*
		 * Write the LSB then MSB.
		 *
		 * If the simultaneous xfer mode is selected by the
		 * jumper on the card, a read instruction is needed
		 * in order to initiate the simultaneous transfer.
		 * Otherwise, the DAC will be updated when the MSB
		 * is written.
		 */
		outb(val & 0x00ff, offset);
		outb((val >> 8) & 0x00ff, offset + 1);
	}
	s->readback[chan] = val;

	return insn->n;
}

开发者ID:383530895，项目名称:linux，代码行数:29，代码来源:cb_pcimdda.c

示例12: dac02_ao_insn_write

static int dac02_ao_insn_write(struct comedi_device *dev,
			       struct comedi_subdevice *s,
			       struct comedi_insn *insn,
			       unsigned int *data)
{
	unsigned int chan = CR_CHAN(insn->chanspec);
	unsigned int range = CR_RANGE(insn->chanspec);
	unsigned int val;
	int i;

	for (i = 0; i < insn->n; i++) {
		val = data[i];

		s->readback[chan] = val;

		/*
		 * Unipolar outputs are true binary encoding.
		 * Bipolar outputs are complementary offset binary
		 * (that is, 0 = +full scale, maxdata = -full scale).
		 */
		if (comedi_range_is_bipolar(s, range))
			val = s->maxdata - val;

		/*
		 * DACs are double-buffered.
		 * Write LSB then MSB to latch output.
		 */
		outb((val << 4) & 0xf0, dev->iobase + DAC02_AO_LSB(chan));
		outb((val >> 4) & 0xff, dev->iobase + DAC02_AO_MSB(chan));
	}

	return insn->n;
}

开发者ID:AlexShiLucky，项目名称:linux，代码行数:33，代码来源:dac02.c

示例13: pci1720_ao_insn_write

static int pci1720_ao_insn_write(struct comedi_device *dev,
				 struct comedi_subdevice *s,
				 struct comedi_insn *insn,
				 unsigned int *data)
{
	unsigned int chan = CR_CHAN(insn->chanspec);
	unsigned int range = CR_RANGE(insn->chanspec);
	unsigned int val;
	int i;

	/* set the channel range and polarity */
	val = inb(dev->iobase + PCI1720_AO_RANGE_REG);
	val &= ~PCI1720_AO_RANGE_MASK(chan);
	val |= PCI1720_AO_RANGE(chan, range);
	outb(val, dev->iobase + PCI1720_AO_RANGE_REG);

	val = s->readback[chan];
	for (i = 0; i < insn->n; i++) {
		val = data[i];

		outb(val & 0xff, dev->iobase + PCI1720_AO_LSB_REG(chan));
		outb((val >> 8) & 0xff, dev->iobase + PCI1720_AO_MSB_REG(chan));

		/* conversion time is 2us (500 kHz throughput) */
		usleep_range(2, 100);
	}

	s->readback[chan] = val;

	return insn->n;
}

开发者ID:AlexShiLucky，项目名称:linux，代码行数:31，代码来源:adv_pci1720.c

示例14: multiq3_ai_insn_read

static int multiq3_ai_insn_read(struct comedi_device *dev, struct comedi_subdevice *s,
	struct comedi_insn *insn, unsigned int *data)
{
	int i, n;
	int chan;
	unsigned int hi, lo;

	chan = CR_CHAN(insn->chanspec);
	outw(MULTIQ3_CONTROL_MUST | MULTIQ3_AD_MUX_EN | (chan << 3),
		dev->iobase + MULTIQ3_CONTROL);

	for (i = 0; i < MULTIQ3_TIMEOUT; i++) {
		if (inw(dev->iobase + MULTIQ3_STATUS) & MULTIQ3_STATUS_EOC)
			break;
	}
	if (i == MULTIQ3_TIMEOUT)
		return -ETIMEDOUT;

	for (n = 0; n < insn->n; n++) {
		outw(0, dev->iobase + MULTIQ3_AD_CS);
		for (i = 0; i < MULTIQ3_TIMEOUT; i++) {
			if (inw(dev->iobase +
					MULTIQ3_STATUS) & MULTIQ3_STATUS_EOC_I)
				break;
		}
		if (i == MULTIQ3_TIMEOUT)
			return -ETIMEDOUT;

		hi = inb(dev->iobase + MULTIQ3_AD_CS);
		lo = inb(dev->iobase + MULTIQ3_AD_CS);
		data[n] = (((hi << 8) | lo) + 0x1000) & 0x1fff;
	}

	return n;
}

开发者ID:AppEngine，项目名称:linux-2.6，代码行数:35，代码来源:multiq3.c

示例15: subdev_3724_insn_config

/* overriding the 8255 insn config */
static int subdev_3724_insn_config(struct comedi_device *dev,
				   struct comedi_subdevice *s,
				   struct comedi_insn *insn,
				   unsigned int *data)
{
	unsigned int chan = CR_CHAN(insn->chanspec);
	unsigned int mask;
	int ret;

	if (chan < 8)
		mask = 0x0000ff;
	else if (chan < 16)
		mask = 0x00ff00;
	else if (chan < 20)
		mask = 0x0f0000;
	else
		mask = 0xf00000;

	ret = comedi_dio_insn_config(dev, s, insn, data, mask);
	if (ret)
		return ret;

	do_3724_config(dev, s, insn->chanspec);
	enable_chan(dev, s, insn->chanspec);

	return insn->n;
}

开发者ID:AeroGirl，项目名称:VAR-SOM-AM33-SDK7-Kernel，代码行数:28，代码来源:pcm3724.c

示例16: usbduxsigma_ai_cmd

static int usbduxsigma_ai_cmd(struct comedi_device *dev,
			      struct comedi_subdevice *s)
{
	struct usbduxsigma_private *devpriv = dev->private;
	struct comedi_cmd *cmd = &s->async->cmd;
	unsigned int len = cmd->chanlist_len;
	uint8_t muxsg0 = 0;
	uint8_t muxsg1 = 0;
	uint8_t sysred = 0;
	int ret;
	int i;

	down(&devpriv->sem);

	/* set current channel of the running acquisition to zero */
	s->async->cur_chan = 0;
	for (i = 0; i < len; i++) {
		unsigned int chan  = CR_CHAN(cmd->chanlist[i]);

		create_adc_command(chan, &muxsg0, &muxsg1);
	}

	devpriv->dux_commands[1] = len;  /* num channels per time step */
	devpriv->dux_commands[2] = 0x12; /* CONFIG0 */
	devpriv->dux_commands[3] = 0x03; /* CONFIG1: 23kHz sample, delay 0us */
	devpriv->dux_commands[4] = 0x00; /* CONFIG3: diff. channels off */
	devpriv->dux_commands[5] = muxsg0;
	devpriv->dux_commands[6] = muxsg1;
	devpriv->dux_commands[7] = sysred;

	ret = usbbuxsigma_send_cmd(dev, USBBUXSIGMA_AD_CMD);
	if (ret < 0) {
		up(&devpriv->sem);
		return ret;
	}

	devpriv->ai_counter = devpriv->ai_timer;

	if (cmd->start_src == TRIG_NOW) {
		/* enable this acquisition operation */
		devpriv->ai_cmd_running = 1;
		ret = usbduxsigma_submit_urbs(dev, devpriv->ai_urbs,
					      devpriv->n_ai_urbs, 1);
		if (ret < 0) {
			devpriv->ai_cmd_running = 0;
			up(&devpriv->sem);
			return ret;
		}
		s->async->inttrig = NULL;
	} else {	/* TRIG_INT */
		/* wait for an internal signal and submit the urbs later */
		s->async->inttrig = usbduxsigma_ai_inttrig;
	}

	up(&devpriv->sem);

	return 0;
}

开发者ID:7799，项目名称:linux，代码行数:58，代码来源:usbduxsigma.c

示例17: ni_660x_set_second_gate

static int ni_660x_set_second_gate(struct ni_gpct *counter,
	lsampl_t gate_source)
{
	struct ni_gpct_device *counter_dev = counter->counter_dev;
	const unsigned second_gate_reg =
		NITIO_Gi_Second_Gate_Reg(counter->counter_index);
	const unsigned selected_second_gate = CR_CHAN(gate_source);
	/* bits of second_gate that may be meaningful to second gate register */
	static const unsigned selected_second_gate_mask = 0x1f;
	unsigned ni_660x_second_gate_select;
	unsigned i;

	switch (selected_second_gate) {
	case NI_GPCT_SOURCE_PIN_i_GATE_SELECT:
	case NI_GPCT_UP_DOWN_PIN_i_GATE_SELECT:
	case NI_GPCT_SELECTED_GATE_GATE_SELECT:
	case NI_GPCT_NEXT_OUT_GATE_SELECT:
	case NI_GPCT_LOGIC_LOW_GATE_SELECT:
		ni_660x_second_gate_select =
			selected_second_gate & selected_second_gate_mask;
		break;
	case NI_GPCT_NEXT_SOURCE_GATE_SELECT:
		ni_660x_second_gate_select =
			NI_660x_Next_SRC_Second_Gate_Select;
		break;
	default:
		for (i = 0; i <= ni_660x_max_rtsi_channel; ++i) {
			if (selected_second_gate == NI_GPCT_RTSI_GATE_SELECT(i)) {
				ni_660x_second_gate_select =
					selected_second_gate &
					selected_second_gate_mask;
				break;
			}
		}
		if (i <= ni_660x_max_rtsi_channel)
			break;
		for (i = 0; i <= ni_660x_max_up_down_pin; ++i) {
			if (selected_second_gate ==
				NI_GPCT_UP_DOWN_PIN_GATE_SELECT(i)) {
				ni_660x_second_gate_select =
					selected_second_gate &
					selected_second_gate_mask;
				break;
			}
		}
		if (i <= ni_660x_max_up_down_pin)
			break;
		return -EINVAL;
		break;
	};
	counter_dev->regs[second_gate_reg] |= Gi_Second_Gate_Mode_Bit;
	counter_dev->regs[second_gate_reg] &= ~Gi_Second_Gate_Select_Mask;
	counter_dev->regs[second_gate_reg] |=
		Gi_Second_Gate_Select_Bits(ni_660x_second_gate_select);
	write_register(counter, counter_dev->regs[second_gate_reg],
		second_gate_reg);
	return 0;
}

开发者ID:jbetten，项目名称:rtxi，代码行数:58，代码来源:ni_tio.c

示例18: das16_ai_rinsn

static int das16_ai_rinsn(struct comedi_device *dev, struct comedi_subdevice *s,
			  struct comedi_insn *insn, unsigned int *data)
{
	const struct das16_board *board = comedi_board(dev);
	int i, n;
	int range;
	int chan;
	int msb, lsb;

	/*  disable interrupts and pacing */
	devpriv->control_state &= ~DAS16_INTE & ~DMA_ENABLE & ~PACING_MASK;
	outb(devpriv->control_state, dev->iobase + DAS16_CONTROL);

	/* set multiplexer */
	chan = CR_CHAN(insn->chanspec);
	chan |= CR_CHAN(insn->chanspec) << 4;
	outb(chan, dev->iobase + DAS16_MUX);

	/* set gain */
	if (board->ai_pg != das16_pg_none) {
		range = CR_RANGE(insn->chanspec);
		outb((das16_gainlists[board->ai_pg])[range],
		     dev->iobase + DAS16_GAIN);
	}

	for (n = 0; n < insn->n; n++) {
		/* trigger conversion */
		outb_p(0, dev->iobase + DAS16_TRIG);

		for (i = 0; i < DAS16_TIMEOUT; i++) {
			if (!(inb(dev->iobase + DAS16_STATUS) & BUSY))
				break;
		}
		if (i == DAS16_TIMEOUT) {
			printk("das16: timeout\n");
			return -ETIME;
		}
		msb = inb(dev->iobase + DAS16_AI_MSB);
		lsb = inb(dev->iobase + DAS16_AI_LSB);
		if (board->ai_nbits == 12)
			data[n] = ((lsb >> 4) & 0xf) | (msb << 4);
		else
			data[n] = lsb | (msb << 8);

	}

开发者ID:ARMWorks，项目名称:FA_2451_Linux_Kernel，代码行数:45，代码来源:das16.c

示例19: daq700_ai_rinsn

static int daq700_ai_rinsn(struct comedi_device *dev,
			   struct comedi_subdevice *s,
			   struct comedi_insn *insn, unsigned int *data)
{
	int n, i, chan;
	int d;
	unsigned int status;
	enum { TIMEOUT = 100 };

	chan = CR_CHAN(insn->chanspec);
	/* write channel to multiplexer */
	/* set mask scan bit high to disable scanning */
	outb(chan | 0x80, dev->iobase + CMD_R1);
	/* mux needs 2us to really settle [Fred Brooks]. */
	udelay(2);

	/* convert n samples */
	for (n = 0; n < insn->n; n++) {
		/* trigger conversion with out0 L to H */
		outb(0x00, dev->iobase + CMD_R2); /* enable ADC conversions */
		outb(0x30, dev->iobase + CMO_R); /* mode 0 out0 L, from H */
		/* mode 1 out0 H, L to H, start conversion */
		outb(0x32, dev->iobase + CMO_R);
		/* wait for conversion to end */
		for (i = 0; i < TIMEOUT; i++) {
			status = inb(dev->iobase + STA_R2);
			if ((status & 0x03) != 0) {
				dev_info(dev->class_dev,
					 "Overflow/run Error\n");
				return -EOVERFLOW;
			}
			status = inb(dev->iobase + STA_R1);
			if ((status & 0x02) != 0) {
				dev_info(dev->class_dev, "Data Error\n");
				return -ENODATA;
			}
			if ((status & 0x11) == 0x01) {
				/* ADC conversion complete */
				break;
			}
			udelay(1);
		}
		if (i == TIMEOUT) {
			dev_info(dev->class_dev,
				 "timeout during ADC conversion\n");
			return -ETIMEDOUT;
		}
		/* read data */
		d = inw(dev->iobase + ADFIFO_R);
		/* mangle the data as necessary */
		/* Bipolar Offset Binary: 0 to 4095 for -10 to +10 */
		d &= 0x0fff;
		d ^= 0x0800;
		data[n] = d;
	}
	return n;
}

开发者ID:LuweiLight，项目名称:linux-3.14.35-vbal，代码行数:57，代码来源:ni_daq_700.c

示例20: usbduxsigma_ai_insn_read

static int usbduxsigma_ai_insn_read(struct comedi_device *dev,
				    struct comedi_subdevice *s,
				    struct comedi_insn *insn,
				    unsigned int *data)
{
	struct usbduxsigma_private *devpriv = dev->private;
	unsigned int chan = CR_CHAN(insn->chanspec);
	uint8_t muxsg0 = 0;
	uint8_t muxsg1 = 0;
	uint8_t sysred = 0;
	int ret;
	int i;

	down(&devpriv->sem);
	if (devpriv->ai_cmd_running) {
		up(&devpriv->sem);
		return -EBUSY;
	}

	create_adc_command(chan, &muxsg0, &muxsg1);

	/* Mode 0 is used to get a single conversion on demand */
	devpriv->dux_commands[1] = 0x16; /* CONFIG0: chopper on */
	devpriv->dux_commands[2] = 0x80; /* CONFIG1: 2kHz sampling rate */
	devpriv->dux_commands[3] = 0x00; /* CONFIG3: diff. channels off */
	devpriv->dux_commands[4] = muxsg0;
	devpriv->dux_commands[5] = muxsg1;
	devpriv->dux_commands[6] = sysred;

	/* adc commands */
	ret = usbbuxsigma_send_cmd(dev, USBDUXSIGMA_SINGLE_AD_CMD);
	if (ret < 0) {
		up(&devpriv->sem);
		return ret;
	}

	for (i = 0; i < insn->n; i++) {
		uint32_t val;

		ret = usbduxsigma_receive_cmd(dev, USBDUXSIGMA_SINGLE_AD_CMD);
		if (ret < 0) {
			up(&devpriv->sem);
			return ret;
		}

		/* 32 bits big endian from the A/D converter */
		val = be32_to_cpu(get_unaligned((__be32
						 *)(devpriv->insn_buf + 1)));
		val &= 0x00ffffff;	/* strip status byte */
		val ^= 0x00800000;	/* convert to unsigned */

		data[i] = val;
	}
	up(&devpriv->sem);

	return insn->n;
}

开发者ID:3null，项目名称:linux，代码行数:57，代码来源:usbduxsigma.c

注：本文中的CR_CHAN函数示例整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ CR_DDI_PROLOGUE函数代码示例发布时间：2022-05-30

C++ CRY_ASSERT_MESSAGE函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：18323|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9698|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8193|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8559|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8469|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9410|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8443|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7875|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8427|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7403|2022-11-06

客服电话

电子邮件

C++ CR_CHAN函数代码示例

示例1: dmm32at_ai_check_chanlist

示例2: ni_m_series_set_second_gate

示例3: multiq3_ai_insn_read

示例4: usbduxsigma_ao_insn_write

示例5: pci6208_ao_insn_write

示例6: dt2815_ao_insn

示例7: dio200_start_intr

示例8: dt2815_ao_insn

示例9: pcl711_set_changain

示例10: dmm32at_ao_insn_write

示例11: cb_pcimdda_ao_insn_write

示例12: dac02_ao_insn_write

示例13: pci1720_ao_insn_write

示例14: multiq3_ai_insn_read

示例15: subdev_3724_insn_config

示例16: usbduxsigma_ai_cmd

示例17: ni_660x_set_second_gate

示例18: das16_ai_rinsn

示例19: daq700_ai_rinsn

示例20: usbduxsigma_ai_insn_read

请发表评论

全部评论

上一篇：

下一篇：

CVE-2022-35285

万里平台泰州会场

kojino/Harvard-Robust-Machine-Learning:

cescoffier/puppet-nexus: A Puppet Module

文的笔顺,诠释文的笔画,解读文的部首

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053