C++ ETS_GPIO_INTR_DISABLE函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中ETS_GPIO_INTR_DISABLE函数的典型用法代码示例。如果您正苦于以下问题：C++ ETS_GPIO_INTR_DISABLE函数的具体用法？C++ ETS_GPIO_INTR_DISABLE怎么用？C++ ETS_GPIO_INTR_DISABLE使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了ETS_GPIO_INTR_DISABLE函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: flowTimerCb

static void ICACHE_FLASH_ATTR flowTimerCb(void) { // 1 second

	if (flowOverridden) {
		ETS_GPIO_INTR_DISABLE();
		flowCount = 0;
		ETS_GPIO_INTR_ENABLE();
	} else {
		ETS_GPIO_INTR_DISABLE();
		oneSecFlowCount = flowCount;
		flowCount = 0;
		ETS_GPIO_INTR_ENABLE();
	}

	flowSetAverage(oneSecFlowCount);
	if (flowAverage == 0) { // Use average to deal with any timing issues when demand oscillates
		INFOP("!");
		secondsNotFlowingCount++;
	} else {
		INFOP(">");
		secondsNotFlowingCount = 0;
	}
	flowCountPerReading += oneSecFlowCount;
	if (oneSecFlowCount < flowMin) {
		flowMin = oneSecFlowCount;
	}
	if (oneSecFlowCount > flowMax) {
		flowMax = oneSecFlowCount;
	}
	calcFlows();
}

开发者ID:Daven005，项目名称:ESP8266，代码行数:30，代码来源:flowMonitor.c

示例2: button_press

void ICACHE_FLASH_ATTR
button_press() {
	ETS_GPIO_INTR_DISABLE(); // Disable gpio interrupts

	// Button interrupt received
	INFO("BUTTON: Button pressed\r\n");

	// Button pressed, flip switch
	if (GPIO_REG_READ(BUTTON_GPIO) & BIT2) {
		INFO("BUTTON: Switch off\r\n");
		GPIO_OUTPUT_SET(SWITCH03_GPIO, 0);
	} else  {
		INFO("BUTTON: Switch on\r\n");
		GPIO_OUTPUT_SET(SWITCH03_GPIO, 1);
	}

	// Send new status to the MQTT broker
	char *json_buf = NULL;
	json_buf = (char *)os_zalloc(jsonSize);
	json_ws_send((struct jsontree_value *)&device_tree, "device", json_buf);
	INFO("BUTTON: Sending current switch status\r\n");
	MQTT_Publish(&mqttClient, config.mqtt_topic_s01, json_buf, strlen(json_buf), 0, 0);
	os_free(json_buf);
	json_buf = NULL;

	// Debounce
	os_delay_us(200000);

	// Clear interrupt status
	uint32 gpio_status;
	gpio_status = GPIO_REG_READ(GPIO_STATUS_ADDRESS);
	GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, gpio_status);

	ETS_GPIO_INTR_ENABLE(); // Enable gpio interrupts
}

开发者ID:felipeacorsi，项目名称:home-assistant_esp8266_mqtt，代码行数:35，代码来源:user_main.c

示例3: i2c_master_gpio_init

/******************************************************************************
 * FunctionName : i2c_master_gpio_init
 * Description  : config SDA and SCL gpio to open-drain output mode,
 *                mux and gpio num defined in i2c_master.h
 * Parameters   : NONE
 * Returns      : NONE
*******************************************************************************/
void ICACHE_FLASH_ATTR
i2c_master_gpio_init(uint8 scl, uint8 sda, uint32 bitrate)
{
    pinSCL = scl;
    pinSDA = sda;

#if 0
    ETS_GPIO_INTR_DISABLE();
//    ETS_INTR_LOCK();

    // Assume the pin mux is set before calling this function
    //PIN_FUNC_SELECT(I2C_MASTER_SDA_MUX, I2C_MASTER_SDA_FUNC);
    //PIN_FUNC_SELECT(I2C_MASTER_SCL_MUX, I2C_MASTER_SCL_FUNC);

    GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(sda)),
        GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(sda))) |
        GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_ENABLE)); //open drain;
    GPIO_REG_WRITE(GPIO_ENABLE_ADDRESS,
        GPIO_REG_READ(GPIO_ENABLE_ADDRESS) | (1 << sda));

    GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(scl)),
        GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(scl))) |
        GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_ENABLE)); //open drain;
    GPIO_REG_WRITE(GPIO_ENABLE_ADDRESS,
        GPIO_REG_READ(GPIO_ENABLE_ADDRESS) | (1 << scl));

    I2C_MASTER_SDA_SCL(1, 1);

    ETS_GPIO_INTR_ENABLE() ;
//    ETS_INTR_UNLOCK();
#endif

    I2C_MASTER_SDA_SCL(1, 1);
    i2c_master_init();
}

开发者ID:nkolban，项目名称:Espruino，代码行数:42，代码来源:i2c_master.c

示例4: spi

static void spi(uint8 c) {
	uint8 mask = 0x80;
	ETS_GPIO_INTR_DISABLE();
	while (mask != 0) {
		if (mask & c) {
//			stdoutPutchar('1');
//			easygpio_outputSet(LCD_Data, 1);
			GPIO_REG_WRITE(GPIO_OUT_W1TS_ADDRESS, (1 << LCD_Data));
		} else {
//			stdoutPutchar('0');
//			easygpio_outputSet(LCD_Data, 0);
			GPIO_REG_WRITE(GPIO_OUT_W1TC_ADDRESS, (1 << LCD_Data));
		}
		mask >>= 1;
		asm volatile (
			"NOP;NOP;NOP;NOP;NOP;"
		);
		GPIO_REG_WRITE(GPIO_OUT_W1TS_ADDRESS, (1 << LCD_clk));
		asm volatile (
			"NOP;NOP;NOP;NOP;NOP;"
			"NOP;NOP;NOP;NOP;NOP;"
		);
		GPIO_REG_WRITE(GPIO_OUT_W1TC_ADDRESS, (1 << LCD_clk));
	}
	ETS_GPIO_INTR_ENABLE();
//	stdoutPutchar(' ');
}

开发者ID:Daven005，项目名称:ESP8266，代码行数:27，代码来源:lcd_5100.c

示例5: GPIO_DIS_OUTPUT

// initialization
void IRrecv::enableIRIn() {
	
  // initialize state machine variables
  irparams.rcvstate = STATE_IDLE;
  irparams.rawlen = 0;

  // set pin modes  
  //PIN_FUNC_SELECT(IR_IN_MUX, IR_IN_FUNC);
  GPIO_DIS_OUTPUT(irparams.recvpin);
  
  // Initialize timer
  os_timer_disarm(&timer);
  os_timer_setfn(&timer, (os_timer_func_t *)read_timeout, &timer);
  
  // ESP Attach Interrupt
  ETS_GPIO_INTR_DISABLE();
  ETS_GPIO_INTR_ATTACH(gpio_intr, NULL);
  gpio_pin_intr_state_set(GPIO_ID_PIN(irparams.recvpin), GPIO_PIN_INTR_ANYEDGE);
  ETS_GPIO_INTR_ENABLE();
  //ETS_INTR_UNLOCK();  
  
  //attachInterrupt(irparams.recvpin, readIR, CHANGE);  
  //irReadTimer.initializeUs(USECPERTICK, readIR).start();
  //os_timer_arm_us(&irReadTimer, USECPERTICK, 1);
  //ets_timer_arm_new(&irReadTimer, USECPERTICK, 1, 0);
}

开发者ID:Leenix，项目名称:Tengu，代码行数:27，代码来源:IRremoteESP8266.cpp

示例6: key_init

/******************************************************************************
 * FunctionName : key_init
 * Description  : init keys
 * Parameters   : key_param *keys - keys parameter, which inited by key_init_single
 * Returns      : none
*******************************************************************************/
void ICACHE_FLASH_ATTR
key_init(struct keys_param *keys)
{
    uint8 i;
    os_printf("-%s-%s \r\n", __FILE__, __func__);

    ETS_GPIO_INTR_ATTACH(key_intr_handler, keys);

    ETS_GPIO_INTR_DISABLE();

    for (i = 0; i < keys->key_num; i++) {
        keys->single_key[i]->key_level = 1;

        PIN_FUNC_SELECT(keys->single_key[i]->gpio_name, keys->single_key[i]->gpio_func);

        gpio_output_set(0, 0, 0, GPIO_ID_PIN(keys->single_key[i]->gpio_id));

        gpio_register_set(GPIO_PIN_ADDR(keys->single_key[i]->gpio_id), GPIO_PIN_INT_TYPE_SET(GPIO_PIN_INTR_DISABLE)
                          | GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_DISABLE)
                          | GPIO_PIN_SOURCE_SET(GPIO_AS_PIN_SOURCE));

        //clear gpio14 status
        GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, BIT(keys->single_key[i]->gpio_id));

        //enable interrupt
        gpio_pin_intr_state_set(GPIO_ID_PIN(keys->single_key[i]->gpio_id), GPIO_PIN_INTR_ANYEGDE);
    }

    ETS_GPIO_INTR_ENABLE();
}

开发者ID:eeijcea，项目名称:ESP8266，代码行数:36，代码来源:key.c

示例7: easygpio_attachInterrupt

/**
 * Sets the 'gpio_pin' pin as a GPIO and sets the interrupt to trigger on that pin.
 * The 'interruptArg' is the function argument that will be sent to your interruptHandler
 */
bool ICACHE_FLASH_ATTR
easygpio_attachInterrupt(uint8_t gpio_pin, EasyGPIO_PullStatus pullStatus, void (*interruptHandler)(void *arg), void *interruptArg) {
  uint32_t gpio_name;
  uint8_t gpio_func;

  if (gpio_pin == 16) {
    os_printf("easygpio_setupInterrupt Error: GPIO16 does not have interrupts\n");
    return false;
  }
  if (!easygpio_getGPIONameFunc(gpio_pin, &gpio_name, &gpio_func) ) {
    return false;
  }

  ETS_GPIO_INTR_ATTACH(interruptHandler, interruptArg);
  ETS_GPIO_INTR_DISABLE();

  PIN_FUNC_SELECT(gpio_name, gpio_func);

  easygpio_setupPullsByName(gpio_name, pullStatus);

  // disable output
  GPIO_DIS_OUTPUT(gpio_pin);

  gpio_register_set(GPIO_PIN_ADDR(gpio_pin), GPIO_PIN_INT_TYPE_SET(GPIO_PIN_INTR_DISABLE)
                    | GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_DISABLE)
                    | GPIO_PIN_SOURCE_SET(GPIO_AS_PIN_SOURCE));

  //clear gpio14 status
  GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, BIT(gpio_pin));
  ETS_GPIO_INTR_ENABLE();

  return true;
}

开发者ID:Zhang-Jia，项目名称:ds1307-plug-demo，代码行数:37，代码来源:tisan_gpio.c

示例8: key_init

/******************************************************************************
 * FunctionName : key_init
 * Description  : init keys
 * Parameters   : key_param *keys - keys parameter, which inited by key_init_single
 * Returns	  : none
*******************************************************************************/
void ICACHE_FLASH_ATTR key_init() {
    uint8 i;

    ETS_GPIO_INTR_ATTACH(key_intr_handler, &key_parameters);

    ETS_GPIO_INTR_DISABLE();

    for (i = 0; i < key_parameters.key_num; i++) {
        key_parameters.single_key[i]->key_level = 1;
        key_parameters.single_key[i]->is_long = 0;

        PIN_FUNC_SELECT(key_parameters.single_key[i]->gpio_name, key_parameters.single_key[i]->gpio_func);

        // Set GPIO as input
        gpio_output_set(0, 0, 0, GPIO_ID_PIN(key_parameters.single_key[i]->gpio_id));

        gpio_register_set(
            GPIO_PIN_ADDR(key_parameters.single_key[i]->gpio_id),
            GPIO_PIN_INT_TYPE_SET(GPIO_PIN_INTR_DISABLE) |
            GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_DISABLE) |
            GPIO_PIN_SOURCE_SET(GPIO_AS_PIN_SOURCE)
        );

        //clear gpio14 status
        GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, BIT(key_parameters.single_key[i]->gpio_id));

        //enable interrupt
        gpio_pin_intr_state_set(GPIO_ID_PIN(key_parameters.single_key[i]->gpio_id), GPIO_PIN_INTR_NEGEDGE);
    }

    ETS_GPIO_INTR_ENABLE();
}

开发者ID:lvjh，项目名称:ESP8266，代码行数:38，代码来源:key.c

示例9: i2c_master_gpio_init

/******************************************************************************
 * FunctionName : i2c_master_gpio_init
 * Description  : config SDA and SCL gpio to open-drain output mode,
 *				mux and gpio num defined in i2c_master.h
 * Parameters   : uint8 sda and scl pin numbers
 * Returns	  : bool, true if init okay
*******************************************************************************/
bool i2c_master_gpio_init(uint8 sda, uint8 scl)
{
	if((sda > GPIO_PIN_NUM) || (pin_func[sda] == GPIO_PIN_FUNC_INVALID)){
		return false;
	}

	if((scl > GPIO_PIN_NUM) || (pin_func[scl] == GPIO_PIN_FUNC_INVALID)){
		return false;
	}

	pinSDA = sda;
	pinSCL = scl;

	ETS_GPIO_INTR_DISABLE() ;
//	ETS_INTR_LOCK();

	PIN_FUNC_SELECT(pin_mux[sda], pin_func[sda]);
	PIN_FUNC_SELECT(pin_mux[scl], pin_func[scl]);

	GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(sda)), GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(sda))) | GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_ENABLE)); //open drain;
	GPIO_REG_WRITE(GPIO_ENABLE_ADDRESS, GPIO_REG_READ(GPIO_ENABLE_ADDRESS) | (1 << sda));
	GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(scl)), GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(scl))) | GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_ENABLE)); //open drain;
	GPIO_REG_WRITE(GPIO_ENABLE_ADDRESS, GPIO_REG_READ(GPIO_ENABLE_ADDRESS) | (1 << scl));

	i2c_master_setDC(1, 1);

	ETS_GPIO_INTR_ENABLE() ;
//	ETS_INTR_UNLOCK();

	i2c_master_init();
	return true;
}

开发者ID:alemoke，项目名称:esp8266-frankenstein，代码行数:39，代码来源:i2c_master.c

示例10: i2c_init

/**
 * I2C init function
 * This sets up the GPIO io
 */
void ICACHE_FLASH_ATTR
i2c_init(void)
{
    //Disable interrupts
    ETS_GPIO_INTR_DISABLE();

    //Set pin functions
    PIN_FUNC_SELECT(I2C_SDA_MUX, I2C_SDA_FUNC);
    PIN_FUNC_SELECT(I2C_SCK_MUX, I2C_SCK_FUNC);

    //Set SDA as open drain
    GPIO_REG_WRITE(
        GPIO_PIN_ADDR(GPIO_ID_PIN(I2C_SDA_PIN)), 
        GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(I2C_SDA_PIN))) | 
        GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_ENABLE)
    );

    GPIO_REG_WRITE(GPIO_ENABLE_ADDRESS, GPIO_REG_READ(GPIO_ENABLE_ADDRESS) | (1 << I2C_SDA_PIN));

    //Set SCK as open drain
    GPIO_REG_WRITE(
        GPIO_PIN_ADDR(GPIO_ID_PIN(I2C_SCK_PIN)), 
        GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(I2C_SCK_PIN))) | 
        GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_ENABLE)
    );

    GPIO_REG_WRITE(GPIO_ENABLE_ADDRESS, GPIO_REG_READ(GPIO_ENABLE_ADDRESS) | (1 << I2C_SCK_PIN));

    //Turn interrupt back on
    ETS_GPIO_INTR_ENABLE();

    i2c_sda(1);
    i2c_sck(1);
    return;
}

开发者ID:Ignat99，项目名称:ESP8266_Relay_Board，代码行数:39，代码来源:i2c.c

示例11: set_gpio_no_interrupt

/*
 * Set GPIO mode to output. Optionally in RAM helper because interrupts are dsabled
 */
static void NO_INTR_CODE set_gpio_no_interrupt(uint8 pin, uint8_t push_pull) {
  unsigned pnum = pin_num[pin];
  ETS_GPIO_INTR_DISABLE();
#ifdef GPIO_INTERRUPT_ENABLE
  pin_int_type[pin] = GPIO_PIN_INTR_DISABLE;
#endif
  PIN_FUNC_SELECT(pin_mux[pin], pin_func[pin]);
  //disable interrupt
  gpio_pin_intr_state_set(GPIO_ID_PIN(pnum), GPIO_PIN_INTR_DISABLE);
  //clear interrupt status
  GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, BIT(pnum));

  // configure push-pull vs open-drain
  if (push_pull) {
    GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(pnum)),
                   GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(pnum))) &
                   (~ GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_ENABLE)));  //disable open drain;
  } else {
    GPIO_REG_WRITE(GPIO_PIN_ADDR(GPIO_ID_PIN(pnum)),
                   GPIO_REG_READ(GPIO_PIN_ADDR(GPIO_ID_PIN(pnum))) |
                   GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_ENABLE));      //enable open drain;
  }

  ETS_GPIO_INTR_ENABLE();
}

开发者ID:nodemcu，项目名称:nodemcu-firmware，代码行数:28，代码来源:platform.c

示例12: user_init

void ICACHE_FLASH_ATTR user_init()
{
    // Initialize the GPIO subsystem.
    //UART_init(BIT_RATE_115200, BIT_RATE_115200, 0);
    //UART_SetPrintPort(UART0);
    stdout_init();

    i2c_master_gpio_init();

    user_set_station_config();

    pcf8754_i2c_write_byte(I2C_INPUT_ADDRESS, 0);
    // =================================================
    // Initialize GPIO2 and GPIO0 as GPIO
    // =================================================
    PIN_FUNC_SELECT(PERIPHS_IO_MUX_U0RXD_U, FUNC_GPIO3);
    PIN_PULLUP_DIS(PERIPHS_IO_MUX_U0RXD_U);

    gpio_output_set(0, 0, 0, GPIO_ID_PIN(3)); // set set gpio 0 as input

    ETS_GPIO_INTR_DISABLE();
    // Attach interrupt handle to gpio interrupts.
    ETS_GPIO_INTR_ATTACH(gpio_intr_handler, NULL);
    GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, BIT(3)); // clear gpio status
    gpio_pin_intr_state_set(GPIO_ID_PIN(3), GPIO_PIN_INTR_ANYEDGE); // clear gpio status.
    ETS_GPIO_INTR_ENABLE(); // Enable interrupts by GPIO


	// register a callback function to let user code know that system
	// initialization is complete
	system_init_done_cb(&post_user_init_func);

    //Start os task
    system_os_task(user_procTask, user_procTaskPrio,user_procTaskQueue, user_procTaskQueueLen);
}

开发者ID:12019，项目名称:esp8266-samplecode，代码行数:35，代码来源:user_main.c

示例13: supla_esp_gpio_init_led

void  supla_esp_gpio_init_led(void) {

	ETS_GPIO_INTR_DISABLE();

	#ifdef LED_RED_PORT
		#if LED_RED_PORT != 16
			GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, BIT(LED_RED_PORT));
			gpio_pin_intr_state_set(GPIO_ID_PIN(LED_RED_PORT), GPIO_PIN_INTR_DISABLE);
			gpio_output_set(0, GPIO_ID_PIN(LED_RED_PORT), GPIO_ID_PIN(LED_RED_PORT), 0);
		#endif
	#endif

	#ifdef LED_GREEN_PORT
		GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, BIT(LED_GREEN_PORT));
		gpio_pin_intr_state_set(GPIO_ID_PIN(LED_GREEN_PORT), GPIO_PIN_INTR_DISABLE);
		gpio_output_set(0, GPIO_ID_PIN(LED_GREEN_PORT), GPIO_ID_PIN(LED_GREEN_PORT), 0);
	#endif

	#ifdef LED_BLUE_PORT
		GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, BIT(LED_BLUE_PORT));
		gpio_pin_intr_state_set(GPIO_ID_PIN(LED_BLUE_PORT), GPIO_PIN_INTR_DISABLE);
		gpio_output_set(0, GPIO_ID_PIN(LED_BLUE_PORT), GPIO_ID_PIN(LED_BLUE_PORT), 0);
	#endif

    ETS_GPIO_INTR_ENABLE();

}

开发者ID:SUPLA，项目名称:supla-core，代码行数:27，代码来源:supla_esp_gpio.c

示例14: disable_interrupt

void ICACHE_FLASH_ATTR disable_interrupt(){
	if(interrupt_set){
		uart0_sendStr("disable interrupt\n");
		//disable interrupt if it is enabled
		ETS_GPIO_INTR_DISABLE();

		interrupt_set=0;
	}
}

开发者ID:na1pir，项目名称:as3935_esp8266_iot，代码行数:9，代码来源:as3935.c

示例15: init_gpio

void ICACHE_FLASH_ATTR
init_gpio(void)
{
    ETS_GPIO_INTR_DISABLE();

    gpio_init();

    PIN_FUNC_SELECT(PERIPHS_IO_MUX_GPIO2_U, FUNC_GPIO2);
    PIN_PULLUP_DIS(PERIPHS_IO_MUX_GPIO2_U);
}

开发者ID:neuro-sys，项目名称:esp8266_ds18b20，代码行数:10，代码来源:user_main.c

示例16: set_gpio_interrupt

static void NO_INTR_CODE set_gpio_interrupt(uint8 pin) {
  ETS_GPIO_INTR_DISABLE();
  PIN_FUNC_SELECT(pin_mux[pin], pin_func[pin]);
  GPIO_DIS_OUTPUT(pin_num[pin]);
  gpio_register_set(GPIO_PIN_ADDR(GPIO_ID_PIN(pin_num[pin])),
                    GPIO_PIN_INT_TYPE_SET(GPIO_PIN_INTR_DISABLE)
                    | GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_DISABLE)
                    | GPIO_PIN_SOURCE_SET(GPIO_AS_PIN_SOURCE));
  ETS_GPIO_INTR_ENABLE();
}

开发者ID:nodemcu，项目名称:nodemcu-firmware，代码行数:10，代码来源:platform.c

示例17: user_plug_set_status

/******************************************************************************
 * FunctionName : user_plug_set_status
 * Description  : set plug's status, 0x00 or 0x01
 * Parameters   : uint8 - status
 * Returns      : none
*******************************************************************************/
void ICACHE_FLASH_ATTR
user_plug_set_status(bool status)
{
//    if (status != plug_param.status) {
//        if (status > 1) {
//            os_printf("error status input!\n");
//            return;
//        }
//
//        plug_param.status = status;
//        PLUG_STATUS_OUTPUT(PLUG_RELAY_LED_IO_NUM, status);
//    }
    if (status != plug_param.status) {
        if (status > 1) {
            os_printf("error status input!\n");
            return;
        }

        plug_param.status = status;
        //PLUG_STATUS_OUTPUT(PLUG_RELAY_LED_IO_NUM, status);

		ETS_GPIO_INTR_DISABLE();
		PIN_FUNC_SELECT(pin_mux[pin], pin_func[pin]);
		GPIO_DIS_OUTPUT(pin_num[pin]);
		gpio_register_set(GPIO_PIN_ADDR(GPIO_ID_PIN(pin_num[pin])), GPIO_PIN_INT_TYPE_SET(GPIO_PIN_INTR_DISABLE)
                    | GPIO_PIN_PAD_DRIVER_SET(GPIO_PAD_DRIVER_DISABLE)
                    | GPIO_PIN_SOURCE_SET(GPIO_AS_PIN_SOURCE));
		ETS_GPIO_INTR_ENABLE();

		//disable global interrupt
		ETS_GPIO_INTR_DISABLE();
		//clear interrupt status
		GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, BIT(pin_num[pin]));
		pin_int_type[pin] = type;
		//enable interrupt
		gpio_pin_intr_state_set(GPIO_ID_PIN(pin_num[pin]), type);
		//enable global interrupt
		ETS_GPIO_INTR_ENABLE();

		ETS_GPIO_INTR_ATTACH(func, arg)
    }
}

开发者ID:FRANZEE，项目名称:My_IoT_Demo，代码行数:48，代码来源:user_plug.c

示例18: gpio_init

void ICACHE_FLASH_ATTR
gpio_init() {
	// Configure switch (relays)
	INFO("Configure Switch 1 %d\n", SWITCH01_GPIO );
	PIN_FUNC_SELECT(SWITCH01_GPIO_MUX, SWITCH01_GPIO_FUNC);
	set_switch(SWITCH01_GPIO, 0);
	//GPIO_OUTPUT_SET(SWITCH01_GPIO, 0);

	INFO("Configure Switch 2 %d\n", SWITCH02_GPIO );
	PIN_FUNC_SELECT(SWITCH02_GPIO_MUX, SWITCH02_GPIO_FUNC);
	set_switch(SWITCH02_GPIO, 0);
	//GPIO_OUTPUT_SET(SWITCH02_GPIO, 0);

	INFO("Configure Switch 3 %d\n", SWITCH03_GPIO );
	PIN_FUNC_SELECT(SWITCH03_GPIO_MUX, SWITCH03_GPIO_FUNC);
	set_switch(SWITCH03_GPIO, 0);
	//GPIO_OUTPUT_SET(SWITCH03_GPIO, 0);

	//Configure Toggle switches
	INFO("Configure Toggle 1 %d\n", TOGGLE01_GPIO );
	ETS_GPIO_INTR_DISABLE(); // Disable gpio interrupts
	ETS_GPIO_INTR_ATTACH(toggle_changed, 0);  // GPIO interrupt handler
	PIN_FUNC_SELECT(TOGGLE01_GPIO_MUX, TOGGLE01_GPIO_FUNC); // Set function
	GPIO_DIS_OUTPUT(TOGGLE01_GPIO); // Set as input
	gpio_pin_intr_state_set(GPIO_ID_PIN(TOGGLE01_GPIO), GPIO_PIN_INTR_ANYEDGE); // Interrupt on any edge
	//ETS_GPIO_INTR_ENABLE(); // Enable gpio interrupts

	INFO("Configure Toggle 2 %d\n", TOGGLE02_GPIO );
	//ETS_GPIO_INTR_DISABLE(); // Disable gpio interrupts
	//ETS_GPIO_INTR_ATTACH(toggle_changed);  // GPIO interrupt handler
	PIN_FUNC_SELECT(TOGGLE02_GPIO_MUX, TOGGLE02_GPIO_FUNC); // Set function
	GPIO_DIS_OUTPUT(TOGGLE02_GPIO); // Set as input
	gpio_pin_intr_state_set(GPIO_ID_PIN(TOGGLE02_GPIO), GPIO_PIN_INTR_ANYEDGE); // Interrupt on any edge
	//ETS_GPIO_INTR_ENABLE(); // Enable gpio interrupts


	INFO("Configure Toggle 3 %d\n", TOGGLE03_GPIO );
	//ETS_GPIO_INTR_DISABLE(); // Disable gpio interrupts
	//ETS_GPIO_INTR_ATTACH(toggle_changed);  // GPIO interrupt handler
	PIN_FUNC_SELECT(TOGGLE03_GPIO_MUX, TOGGLE03_GPIO_FUNC); // Set function
	GPIO_DIS_OUTPUT(TOGGLE03_GPIO); // Set as input
	gpio_pin_intr_state_set(GPIO_ID_PIN(TOGGLE03_GPIO), GPIO_PIN_INTR_ANYEDGE); // Interrupt on any edge
	ETS_GPIO_INTR_ENABLE(); // Enable gpio interrupts


	// Configure push button
//	INFO("Confgiure push button %d\n", BUTTON_GPIO );
//	ETS_GPIO_INTR_DISABLE(); // Disable gpio interrupts
//	ETS_GPIO_INTR_ATTACH(button_press, BUTTON_GPIO);  // GPIO0 interrupt handler
//	PIN_FUNC_SELECT(BUTTON_GPIO_MUX, BUTTON_GPIO_FUNC); // Set function
//	GPIO_DIS_OUTPUT(BUTTON_GPIO); // Set as input
//	gpio_pin_intr_state_set(GPIO_ID_PIN(BUTTON_GPIO), 2); // Interrupt on negative edge
//	ETS_GPIO_INTR_ENABLE(); // Enable gpio interrupts
}

开发者ID:felipeacorsi，项目名称:home-assistant_esp8266_mqtt，代码行数:54，代码来源:user_main.c

示例19: pin_init0

void pin_init0(void) {
    ETS_GPIO_INTR_DISABLE();
    ETS_GPIO_INTR_ATTACH(pin_intr_handler_iram, NULL);
    // disable all interrupts
    memset(&MP_STATE_PORT(pin_irq_handler)[0], 0, 16 * sizeof(mp_obj_t));
    for (int p = 0; p < 16; ++p) {
        GPIO_REG_WRITE(GPIO_STATUS_W1TC_ADDRESS, 1 << p);
        SET_TRIGGER(p, 0);
    }
    ETS_GPIO_INTR_ENABLE();
}

开发者ID:fabaff，项目名称:micropython，代码行数:11，代码来源:machine_pin.c

示例20: ETS_GPIO_INTR_DISABLE

// Decodes the received IR message
// Returns 0 if no data ready, 1 if data ready.
// Results of decoding are stored in results
bool IRrecv::decode(decode_results *results) {
  if(false==irparams.isValueReady)return false;
  ETS_GPIO_INTR_DISABLE();
  irparams.isValueReady=false;
  results->bits = NEC_BITS;
  results->value = irparams.Value;
  results->decode_type = NEC;

  ETS_GPIO_INTR_ENABLE();

  return true;
}

开发者ID:amin7，项目名称:libpack，代码行数:15，代码来源:IRremoteESP8266_nec.cpp

注：本文中的ETS_GPIO_INTR_DISABLE函数示例整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ ETS_GPIO_INTR_ENABLE函数代码示例发布时间：2022-05-30

C++ ETRACE函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：18313|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9694|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8191|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8557|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8467|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9408|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8441|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7873|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8425|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7402|2022-11-06

客服电话

电子邮件

C++ ETS_GPIO_INTR_DISABLE函数代码示例

示例1: flowTimerCb

示例2: button_press

示例3: i2c_master_gpio_init

示例4: spi

示例5: GPIO_DIS_OUTPUT

示例6: key_init

示例7: easygpio_attachInterrupt

示例8: key_init

示例9: i2c_master_gpio_init

示例10: i2c_init

示例11: set_gpio_no_interrupt

示例12: user_init

示例13: supla_esp_gpio_init_led

示例14: disable_interrupt

示例15: init_gpio

示例16: set_gpio_interrupt

示例17: user_plug_set_status

示例18: gpio_init

示例19: pin_init0

示例20: ETS_GPIO_INTR_DISABLE

请发表评论

全部评论

上一篇：

下一篇：

小程序“功能直达”内测，你读懂了什么？

CVE-2022-31544

librespeed/speedtest: Self-hosted Speedt

avehtari/BDA_m_demos: Bayesian Data Anal

四维彩超怎么看性别？四维看男孩女孩诀窍

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053