C++ HAL_GPIO_TogglePin函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中HAL_GPIO_TogglePin函数的典型用法代码示例。如果您正苦于以下问题：C++ HAL_GPIO_TogglePin函数的具体用法？C++ HAL_GPIO_TogglePin怎么用？C++ HAL_GPIO_TogglePin使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了HAL_GPIO_TogglePin函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: main

int main(void)
{

  int i;

  HAL_Init();
  SystemClock_Config();

  __GPIOC_CLK_ENABLE();

  // LEDs on Discovery F0
  GPIO_InitTypeDef GPIO_InitTypeDefStruct;
  GPIO_InitTypeDefStruct.Pin = GPIO_PIN_9 | GPIO_PIN_8;
  GPIO_InitTypeDefStruct.Mode= GPIO_MODE_OUTPUT_PP;
  GPIO_InitTypeDef* GPIO_Init= & GPIO_InitTypeDefStruct;
  HAL_GPIO_Init(GPIOC,GPIO_Init);



    while (1) {
	for (i = 1000000; i > 0; i--);
        HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_9);
        HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_8);
    }



  /* Infinite loop */
  exit (1);
}

开发者ID:Xinxin19871118，项目名称:stm32-codeblocks，代码行数:30，代码来源:main.c

示例2: send

void send(uint8_t status, uint8_t* buffer, uint8_t buffer_length) {
  uint8_t transmitBuffer[UART_command_length + 1];
  transmitBuffer[0] = MORE_DATA;
  uint8_t total_transmitted = 0;
  while (total_transmitted < buffer_length) {
    if (buffer_length - total_transmitted <= UART_command_length) {
      transmitBuffer[0] = status;
    }
    for (int i = 0; i < UART_command_length; i++) {
      if (total_transmitted < buffer_length) {
        transmitBuffer[i+1] = buffer[total_transmitted];
      } else {
        transmitBuffer[i+1] = 0;
      }
      total_transmitted++;
    }
    if (HAL_UART_Transmit(&hUART, (unsigned char*) transmitBuffer, UART_command_length + 1, 1000) != HAL_OK) {
      Output_High(FAIL_LED_GPIOx, FAIL_LED_Pin);
      Output_High(BUSY_LED_GPIOx, BUSY_LED_Pin);
      for (int i = 0; i < 10; i++) {
        HAL_GPIO_TogglePin(FAIL_LED_GPIOx, FAIL_LED_Pin);
        HAL_GPIO_TogglePin(BUSY_LED_GPIOx, BUSY_LED_Pin);
        HAL_Delay(50);
      }
    }
    HAL_Delay(100);
  }
}

开发者ID:chickadee-tech，项目名称:g-test-bot，代码行数:28，代码来源:main.cpp

示例3: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* This sample code shows how to use GPIO HAL API to toggle LED1, LED2, LED3 and LED4 IOs
    in an infinite loop. */

  /* STM32F3xx HAL library initialization:
       - Configure the Flash prefetch
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Set NVIC Group Priority to 4
       - Low Level Initialization
     */
  HAL_Init();

  /* Configure the system clock to 72 MHz */
  SystemClock_Config();
  
  /* -1- Enable each GPIO Clock (to be able to program the configuration registers) */
  LED1_GPIO_CLK_ENABLE();
  LED2_GPIO_CLK_ENABLE();
  LED3_GPIO_CLK_ENABLE();
  LED4_GPIO_CLK_ENABLE();

  /* -2- Configure IOs in output push-pull mode to drive external LEDs */
  GPIO_InitStruct.Mode  = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull  = GPIO_PULLUP;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;

  GPIO_InitStruct.Pin = LED1_PIN;
  HAL_GPIO_Init(LED1_GPIO_PORT, &GPIO_InitStruct);

  GPIO_InitStruct.Pin = LED2_PIN;
  HAL_GPIO_Init(LED2_GPIO_PORT, &GPIO_InitStruct);

  GPIO_InitStruct.Pin = LED3_PIN;
  HAL_GPIO_Init(LED3_GPIO_PORT, &GPIO_InitStruct);

  GPIO_InitStruct.Pin = LED4_PIN;
  HAL_GPIO_Init(LED4_GPIO_PORT, &GPIO_InitStruct);

  /* -3- Toggle IOs in an infinite loop */
  while (1)
  {
    HAL_GPIO_TogglePin(LED1_GPIO_PORT, LED1_PIN);
    /* Insert delay 100 ms */
    HAL_Delay(100);
    HAL_GPIO_TogglePin(LED2_GPIO_PORT, LED2_PIN);
    /* Insert delay 100 ms */
    HAL_Delay(100);
    HAL_GPIO_TogglePin(LED3_GPIO_PORT, LED3_PIN);
    /* Insert delay 100 ms */
    HAL_Delay(100);
    HAL_GPIO_TogglePin(LED4_GPIO_PORT, LED4_PIN);
    /* Insert delay 100 ms */
    HAL_Delay(100);
  }
}

开发者ID:PaxInstruments，项目名称:STM32CubeF3，代码行数:65，代码来源:main.c

示例4: main

int main(void)
{
  uint32_t bootStatus;
  
  /* MCU Configuration----------------------------------------------------------*/
  
  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();
  
  /* Configure the system clock */
  SystemClock_Config();
  
  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  
  /* Turn on led Init */
  HAL_GPIO_WritePin(GPIOE, GPIO_PIN_12|GPIO_PIN_13, GPIO_PIN_RESET);
  
  /* Wait for timeout */
  bootStatus = bootWait(5000);
  
  /* Turn off led */
  HAL_GPIO_WritePin(GPIOE, GPIO_PIN_12|GPIO_PIN_13, GPIO_PIN_SET);
  
  /* Check for Result */
  if(bootStatus == 0)
  {
    /* Test if user code is programmed starting from address USBD_DFU_APP_DEFAULT_ADD */
    if(((*(__IO uint32_t*)USBD_DFU_APP_DEFAULT_ADD) & 0x2FFE0000 ) == 0x20000000)
    {
      /* Jump to user application */
      JumpAddress = *(__IO uint32_t*) (USBD_DFU_APP_DEFAULT_ADD + 4);
      JumpToApplication = (pFunction) JumpAddress;
      
      /* Initialize user application's Stack Pointer */
      __set_MSP(*(__IO uint32_t*) USBD_DFU_APP_DEFAULT_ADD);
      JumpToApplication();
    }
    
    /* load application failed */
    while (1)
    {
      HAL_Delay(50);
      HAL_GPIO_TogglePin(GPIOE, GPIO_PIN_12|GPIO_PIN_13);
    }
  }
  
  /* Init Device Library,Add Supported Class and Start the library*/
  USBD_Init(&hUsbDeviceFS, &FS_Desc, DEVICE_FS);
  USBD_RegisterClass(&hUsbDeviceFS, &USBD_DFU);
  USBD_DFU_RegisterMedia(&hUsbDeviceFS, &USBD_DFU_fops_FS);
  USBD_Start(&hUsbDeviceFS);
  
  /* Infinite loop */
  while (1)
  {
    HAL_Delay(500);
    HAL_GPIO_TogglePin(GPIOE, GPIO_PIN_13);
  }
}

开发者ID:loopedison，项目名称:mFlight，代码行数:60，代码来源:main.c

示例5: main

int main(void)
{
  /* USER CODE BEGIN 1 */

  /* USER CODE END 1 */


  /* USER CODE BEGIN 2 */
  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
      HAL_GPIO_TogglePin(GPIOB, GPIO_PIN_2);
      HAL_Delay(100);
      HAL_GPIO_TogglePin(GPIOE, GPIO_PIN_8);
      HAL_Delay(100);

  /* USER CODE END WHILE */

  /* USER CODE BEGIN 3 */

  }
  /* USER CODE END 3 */

}

开发者ID:Montanari9，项目名称:STM32L4_Short，代码行数:27，代码来源:lab1_blinky.c

示例6: can2RxCpltCallback

/**
  * @brief  Rx Transfer completed callback
  * @param  None
  * @retval None
  */
void can2RxCpltCallback()
{
//	if ((CAN_Handle.pRxMsg->StdId == 0x321) && (CAN_Handle.pRxMsg->IDE == CAN_ID_STD) && (CAN_Handle.pRxMsg->DLC == 2))
//	{
//		HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_3);
//		volatile uint8_t test1 = CAN_Handle.pRxMsg->Data[0];
//		volatile uint8_t test2 = CAN_Handle.pRxMsg->Data[1];
//	}

	if (prvRxBuffer1State != CANBufferState_Reading && prvRxBuffer1Count < RX_BUFFER_SIZE)
	{
		HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_3);
		prvRxBuffer1State = CANBufferState_Writing;
		/* Save the message */
		prvRxBuffer1[prvRxBuffer1CurrentIndex].id = CAN_Handle.pRxMsg->StdId;
		prvRxBuffer1[prvRxBuffer1CurrentIndex].dlc = CAN_Handle.pRxMsg->DLC;
		for (uint32_t i = 0; i < CAN_Handle.pRxMsg->DLC; i++)
			prvRxBuffer1[prvRxBuffer1CurrentIndex].data[i] = CAN_Handle.pRxMsg->Data[i];

		/* Increment the counters */
		prvRxBuffer1CurrentIndex++;
		prvRxBuffer1Count++;

		/* Start the timer which will clear the buffer if it's not already started */
		if (xTimerIsTimerActive(prvBuffer1ClearTimer) == pdFALSE)
			xTimerStartFromISR(prvBuffer1ClearTimer, NULL);
	}
	else if (prvRxBuffer2State != CANBufferState_Reading && prvRxBuffer2Count < RX_BUFFER_SIZE)
	{
		HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_3);
		prvRxBuffer2State = CANBufferState_Writing;
		/* Save the message */
		prvRxBuffer2[prvRxBuffer1CurrentIndex].id = CAN_Handle.pRxMsg->StdId;
		prvRxBuffer2[prvRxBuffer1CurrentIndex].dlc = CAN_Handle.pRxMsg->DLC;
		for (uint32_t i = 0; i < CAN_Handle.pRxMsg->DLC; i++)
			prvRxBuffer2[prvRxBuffer1CurrentIndex].data[i] = CAN_Handle.pRxMsg->Data[i];

		/* Increment the counters */
		prvRxBuffer2CurrentIndex++;
		prvRxBuffer2Count++;

		/* Start the timer which will clear the buffer if it's not already started */
		if (xTimerIsTimerActive(prvBuffer2ClearTimer) == pdFALSE)
			xTimerStartFromISR(prvBuffer2ClearTimer, NULL);
	}
	else
	{
		/* No buffer available, something has gone wrong */
		HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_3);
	}


	/* Receive */
	if (HAL_CAN_Receive_IT(&CAN_Handle, CAN_FIFO1) != HAL_OK)
	{
		/* Reception Error */
//		Error_Handler();
	}
}

开发者ID:hampussandberg，项目名称:HexConnect，代码行数:64，代码来源:can2_task.c

示例7: HAL_ADC_ConvCpltCallback

void HAL_ADC_ConvCpltCallback(ADC_HandleTypeDef* AdcHandle)
{	
	HAL_GPIO_TogglePin(GPIOB, GPIO_PIN_9);
	HAL_ADC_Stop_DMA(&g_AdcHandle);
	osSignalSet(tid_TH_GUI,DMA_ConvCpltSig);
	HAL_GPIO_TogglePin(GPIOB, GPIO_PIN_9);
	//GPIOB->ODR ^= GPIO_PIN_9; // this is just for test of DMA speed
}

开发者ID:AdrK，项目名称:STM32F7_ADC_DMA_LCD，代码行数:8，代码来源:ADC+Config.c

示例8: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
    /* STM32F2xx HAL library initialization:
         - Configure the Flash prefetch, instruction and Data caches
         - Configure the Systick to generate an interrupt each 1 msec
         - Set NVIC Group Priority to 4
         - Global MSP (MCU Support Package) initialization
       */
    HAL_Init();

    /* Configure the system clock to 120 MHz */
    SystemClock_Config();

    /* -1- Enable GPIOG, GPIOC and GPIOI Clock (to be able to program the configuration registers) */
    __HAL_RCC_GPIOG_CLK_ENABLE();
    __HAL_RCC_GPIOC_CLK_ENABLE();
    __HAL_RCC_GPIOI_CLK_ENABLE();

    /* -2- Configure PG.6, PG.8, PI.9 and PC.7 IOs in output push-pull mode to
           drive external LEDs */
    GPIO_InitStruct.Pin = (GPIO_PIN_6 | GPIO_PIN_8);
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_PULLUP;
    GPIO_InitStruct.Speed = GPIO_SPEED_FAST;

    HAL_GPIO_Init(GPIOG, &GPIO_InitStruct);

    GPIO_InitStruct.Pin = GPIO_PIN_9;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_PULLUP;
    GPIO_InitStruct.Speed = GPIO_SPEED_FAST;

    HAL_GPIO_Init(GPIOI, &GPIO_InitStruct);

    GPIO_InitStruct.Pin = GPIO_PIN_7;
    GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
    GPIO_InitStruct.Pull = GPIO_PULLUP;
    GPIO_InitStruct.Speed = GPIO_SPEED_FAST;

    HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);

    /* -3- Toggle PG.6, PG.8, PI.9 and PC.7 IOs in an infinite loop */
    while (1)
    {
        HAL_GPIO_TogglePin(GPIOG, GPIO_PIN_6);
        /* Insert delay 100 ms */
        HAL_Delay(100);
        HAL_GPIO_TogglePin(GPIOG, GPIO_PIN_8);
        /* Insert delay 100 ms */
        HAL_Delay(100);
        HAL_GPIO_TogglePin(GPIOI, GPIO_PIN_9);
        /* Insert delay 100 ms */
        HAL_Delay(100);
        HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_7);
        /* Insert delay 100 ms */
        HAL_Delay(100);
    }
}

开发者ID:PaxInstruments，项目名称:STM32CubeF2，代码行数:63，代码来源:main.c

示例9: main

int main(void)
{

  /* USER CODE BEGIN 1 */
	char ADC_Tx_Data[70];
  /* USER CODE END 1 */

  /* MCU Configuration----------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* Configure the system clock */
  SystemClock_Config();

  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_DMA_Init();
  MX_ADC1_Init();
  MX_USART1_UART_Init();

  /* USER CODE BEGIN 2 */
	
	HAL_UART_Receive_IT(&huart1, (uint8_t *)Rx_Data, 1);
	HAL_ADC_Start_DMA(&hadc1, (uint32_t*)&ADC_Value, 6);

  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
		HAL_Delay(15);
		HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_4);
		HAL_Delay(15);
		HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_0);	
		HAL_Delay(15);
		HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_1);	
		HAL_Delay(15);
		HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_2);	
		HAL_Delay(15);		
	  sprintf(ADC_Tx_Data,"ADC1:%4d\tADC2:%4d\tADC3:%4d\tADC4:%4d\tADC5:%4d\tADC6:%4d\n\r", ADC_Value[0], ADC_Value[1], ADC_Value[2], ADC_Value[3], ADC_Value[4], ADC_Value[5]);
		HAL_UART_Transmit_IT(&huart1, (uint8_t *)ADC_Tx_Data, 70);
			
  /* USER CODE END WHILE */

  /* USER CODE BEGIN 3 */

  }
  /* USER CODE END 3 */

}

开发者ID:Bit-Embedded-3，项目名称:smart_glove，代码行数:52，代码来源:main.c

示例10: main

int main(void) {

    /* USER CODE BEGIN 1 */

    /* USER CODE END 1 */

    /* MCU Configuration----------------------------------------------------------*/

    /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
    HAL_Init();

    /* Configure the system clock */
    SystemClock_Config();

    /* Initialize all configured peripherals */
    MX_GPIO_Init();
    MX_DMA_Init();
    MX_USART3_UART_Init();
    MX_TIM2_Init();

    /* USER CODE BEGIN 2 */
    nec.timerHandle = &htim2;

    nec.timerChannel = TIM_CHANNEL_1;
    nec.timerChannelActive = HAL_TIM_ACTIVE_CHANNEL_1;

    nec.timingBitBoundary = 1680;
    nec.timingAgcBoundary = 12500;
    nec.type = NEC_NOT_EXTENDED;

    nec.NEC_DecodedCallback = myNecDecodedCallback;
    nec.NEC_ErrorCallback = myNecErrorCallback;
    nec.NEC_RepeatCallback = myNecRepeatCallback;

    NEC_Read(&nec);
    /* USER CODE END 2 */

    /* Infinite loop */
    /* USER CODE BEGIN WHILE */
    while (1) {
        /* USER CODE END WHILE */

        /* USER CODE BEGIN 3 */
        HAL_GPIO_TogglePin(GPIOD, GPIO_PIN_12);
        HAL_Delay(100);
        HAL_GPIO_TogglePin(GPIOD, GPIO_PIN_13);
        HAL_Delay(100);
    }
    /* USER CODE END 3 */

}

开发者ID:Ribster，项目名称:STM32_NEC_Decode，代码行数:51，代码来源:main.c

示例11: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F4xx HAL library initialization:
       - Configure the Flash prefetch, instruction and Data caches
       - Configure the Systick to generate an interrupt each 1 msec
       - Set NVIC Group Priority to 4
       - Global MSP (MCU Support Package) initialization
     */
  HAL_Init();
  
  /* Configure the system clock to 100 MHz */
  SystemClock_Config();
  
  /*##-1- Enable GPIOA Clock (to be able to program the configuration registers) */
  __HAL_RCC_GPIOA_CLK_ENABLE();
  
  /*##-2- Configure PA05 IO in output push-pull mode to drive external LED ###*/  
  GPIO_InitStruct.Pin = GPIO_PIN_5;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
  GPIO_InitStruct.Pull = GPIO_PULLUP;
  GPIO_InitStruct.Speed = GPIO_SPEED_FAST;
  HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); 
   
  /*##-3- Toggle PA05 IO in an infinite loop #################################*/  
  while (1)
  {
    HAL_GPIO_TogglePin(GPIOA, GPIO_PIN_5);
    
    /* Insert a 100ms delay */
    HAL_Delay(100);
  }
}

开发者ID:eemei，项目名称:library-stm32f4，代码行数:37，代码来源:main.c

示例12: LED_Thread1

static void LED_Thread1(void const *argument)
{
	GPIO_InitTypeDef GPIO_InitStruct_LED, GPIO_InitStruct_BUTTON;

	/* GPIO Ports Clock Enable */
	__GPIOI_CLK_ENABLE();

	/*Configure GPIO pin : PI1 */
	GPIO_InitStruct_LED.Pin = GPIO_PIN_1;
	GPIO_InitStruct_LED.Mode = GPIO_MODE_OUTPUT_PP;
	GPIO_InitStruct_LED.Pull = GPIO_NOPULL;
	GPIO_InitStruct_LED.Speed = GPIO_SPEED_LOW;
	HAL_GPIO_Init(GPIOI, &GPIO_InitStruct_LED);

	GPIO_InitStruct_BUTTON.Pin = GPIO_PIN_11;
	GPIO_InitStruct_BUTTON.Mode = GPIO_MODE_INPUT;
	GPIO_InitStruct_BUTTON.Pull = GPIO_PULLUP;
	HAL_GPIO_Init(GPIOI, &GPIO_InitStruct_BUTTON);

	while(1)
	{
		if(HAL_GPIO_ReadPin(GPIOI, GPIO_PIN_11)){
			HAL_GPIO_TogglePin(GPIOI, GPIO_PIN_1);
			HAL_Delay(500);
			printf("Pintando \n");
		}
		HAL_GPIO_WritePin(GPIOI, GPIO_PIN_1, 0);

	}
}

开发者ID:aescacena，项目名称:stm32f7，代码行数:30，代码来源:main.c

示例13: myNecRepeatCallback

void myNecRepeatCallback() {
    char* msg = "Repeat!\n";
    HAL_UART_Transmit_DMA(&huart3, (uint8_t*) msg, strlen(msg));
    HAL_GPIO_TogglePin(GPIOD, GPIO_PIN_15);
    HAL_Delay(10);
    NEC_Read(&nec);
}

开发者ID:Ribster，项目名称:STM32_NEC_Decode，代码行数:7，代码来源:main.c

示例14: rs232RxCpltCallback

/**
  * @brief  Rx Transfer completed callback
  * @param  None
  * @retval None
  */
void rs232RxCpltCallback()
{
	if (prvRxBuffer1State != BUFFERState_Reading && prvRxBuffer1Count < RX_BUFFER_SIZE)
	{
		prvRxBuffer1State = BUFFERState_Writing;
		prvRxBuffer1[prvRxBuffer1CurrentIndex++] = prvReceivedByte;
		prvRxBuffer1Count++;
		/* Start the timer which will clear the buffer if it's not already started */
		if (xTimerIsTimerActive(prvBuffer1ClearTimer) == pdFALSE)
			xTimerStartFromISR(prvBuffer1ClearTimer, NULL);
	}
	else if (prvRxBuffer2State != BUFFERState_Reading && prvRxBuffer2Count < RX_BUFFER_SIZE)
	{
		prvRxBuffer2State = BUFFERState_Writing;
		prvRxBuffer2[prvRxBuffer2CurrentIndex++] = prvReceivedByte;
		prvRxBuffer2Count++;
		/* Start the timer which will clear the buffer if it's not already started */
		if (xTimerIsTimerActive(prvBuffer2ClearTimer) == pdFALSE)
			xTimerStartFromISR(prvBuffer2ClearTimer, NULL);
	}
	else
	{
		/* No buffer available, something has gone wrong */
		HAL_GPIO_TogglePin(GPIOC, GPIO_PIN_3);
	}

	/* Continue receiving data */
	HAL_UART_Receive_IT(&UART_Handle, &prvReceivedByte, 1);
	/* Give back the semaphore now that we are done */
	xSemaphoreGiveFromISR(xSemaphore, NULL);
}

开发者ID:efimefimefim，项目名称:HexConnect，代码行数:36，代码来源:rs232_task.c

示例15: main

int main(void)
{
    HAL_Init();

    led_gpio_init();

    SystemClock_Config();

    mima_init();

    usbKB_init();

    USBD_Init(&USBD_Device, &HID_Desc, 0);

    USBD_RegisterClass(&USBD_Device, USBD_HID_CLASS);

    USBD_CUSTOM_HID_RegisterInterface(&USBD_Device, &USBD_CustomHID_fops);

    USBD_Start(&USBD_Device);

    HAL_Delay(1000);
    USB_KB_type("Hello world", 11);

    while(1) {
        HAL_GPIO_TogglePin(GPIOB, GPIO_PIN_7);
        mima_loop();
    }
}

开发者ID:apeng2012，项目名称:mi_ma_bao，代码行数:28，代码来源:main.c

示例16: digitalToggle

void digitalToggle( uint32_t ulPin )
{
    if ( digitalPinToPort(ulPin) == NULL ) {
        return ;
    }
    HAL_GPIO_TogglePin(digitalPinToPort(ulPin), digitalPinToBitMask(ulPin));
}

开发者ID:evark，项目名称:cbp-halmx，代码行数:7，代码来源:wiring_digital.c

示例17: Thread_LED

 /*----------------------------------------------------------------------------
*      Thread  'LED_Thread': Toggles LED
 *---------------------------------------------------------------------------*/
	void Thread_LED (void const *argument) {
		while(1){
				osDelay(200);
				//printf("LED");
				HAL_GPIO_TogglePin(GPIOD, GPIO_PIN_12);
		}
	}

开发者ID:deepaks4077，项目名称:426-microprcessors，代码行数:10，代码来源:Thread_LED.c

示例18: HAL_TIM_PWM_PulseFinishedCallback

// The following is never bing called:
void  HAL_TIM_PWM_PulseFinishedCallback (TIM_HandleTypeDef *htim)
{
  if ((htim->Instance == easySPIN_TIMER_PWM1) && (htim->Channel == easySPIN_HAL_ACT_CHAN_TIMER_PWM1))
    {
      if (EasySpin_GetDeviceState(0) != INACTIVE)
         {
           EasySpin_StepClockHandler(0);
         }
    }

  if ((htim->Instance == easySPIN_TIMER_PWM2) && (htim->Channel == easySPIN_HAL_ACT_CHAN_TIMER_PWM2))
    {
      if (EasySpin_GetDeviceState(1) != INACTIVE)
         {
           EasySpin_StepClockHandler(1);
         }
   }

  if ((htim->Instance == easySPIN_TIMER_PWM3) && (htim->Channel == easySPIN_HAL_ACT_CHAN_TIMER_PWM3))
    {
      HAL_GPIO_TogglePin(easySPIN_PWM_3_PORT, easySPIN_PWM_3_PIN);
      if (EasySpin_GetDeviceState(2) != INACTIVE)
         {
           EasySpin_StepClockHandler(2);
         }
    }
}

开发者ID:GrandviewIoT，项目名称:Industrial_IoT_Projects，代码行数:28，代码来源:main_easyspin_stepper.c

示例19: main

int main(void)
{

  /* USER CODE BEGIN 1 */

  /* USER CODE END 1 */

  /* MCU Configuration----------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* Configure the system clock */
  SystemClock_Config();

  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  //MX_TIM3_Init();
  //MX_TIM4_Init();

  //HAL_TIM_Base_Start(&htim3);
  //HAL_TIM_Base_Start(&htim4);
  //HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_3);
  //HAL_TIM_PWM_Start(&htim3, TIM_CHANNEL_4);
  //HAL_TIM_PWM_Start(&htim4, TIM_CHANNEL_2);

  HAL_GPIO_WritePin(Led_gpio,Led_pin,GPIO_PIN_SET);
  HAL_Delay(1000);
  HAL_GPIO_WritePin(Led_gpio,Led_pin,GPIO_PIN_RESET);

  HAL_GPIO_WritePin(DcCal_gpio,DcCal_pin,GPIO_PIN_RESET);
  

  char state;
  int cnt;
  cnt = HAL_GetTick();
  while (1)
  {
    state = HAL_GPIO_ReadPin(sens_gpio,sens_ph1_pin);
    state = state << 1;
    state |= HAL_GPIO_ReadPin(sens_gpio,sens_ph2_pin);
    state = state << 1;
    state |= HAL_GPIO_ReadPin(sens_gpio,sens_ph3_pin);

    ApplyPhaseSolid(state);
    if(HAL_GetTick()>1000+cnt) {
      HAL_GPIO_TogglePin(EnGate_gpio,EnGate_pin);
      cnt = HAL_GetTick();
    }

//      if(TIM3->CCR3<200)
//        TIM3->CCR3++;
//      else
//        TIM3->CCR3=0;
//
//      HAL_Delay(20);
  }
  /* USER CODE END 3 */

}

开发者ID:sinaaghli，项目名称:STM32DT，代码行数:60，代码来源:main.c

示例20: vLEDFlashTask

static void vLEDFlashTask( void *pvParameters )
{

	for(;;)
	{
		/* Delay for half the flash period then turn the LED on. */
		//vTaskDelayUntil( &xLastFlashTime, xFlashRate );
		vTaskDelay(500/portTICK_RATE_MS);
		HAL_GPIO_TogglePin(GPIOD, GPIO_PIN_13);

		/* Delay for half the flash period then turn the LED off. */
		//vTaskDelayUntil( &xLastFlashTime, xFlashRate );
		vTaskDelay(500/portTICK_RATE_MS);
		HAL_GPIO_TogglePin(GPIOD, GPIO_PIN_13);
	}
}

开发者ID:khjtony，项目名称:TinyCar_TypeNeg1，代码行数:16，代码来源:flash.c

注：本文中的HAL_GPIO_TogglePin函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ HAL_GPIO_WritePin函数代码示例发布时间：2022-05-30

C++ HAL_GPIO_ReadPin函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：18268|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9677|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8177|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8548|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8457|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9388|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8427|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7862|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8411|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7394|2022-11-06

客服电话

电子邮件

C++ HAL_GPIO_TogglePin函数代码示例

示例1: main

示例2: send

示例3: main

示例4: main

示例5: main

示例6: can2RxCpltCallback

示例7: HAL_ADC_ConvCpltCallback

示例8: main

示例9: main

示例10: main

示例11: main

示例12: LED_Thread1

示例13: myNecRepeatCallback

示例14: rs232RxCpltCallback

示例15: main

示例16: digitalToggle

示例17: Thread_LED

示例18: HAL_TIM_PWM_PulseFinishedCallback

示例19: main

示例20: vLEDFlashTask

请发表评论

全部评论

上一篇：

下一篇：

bradtraversy/iweather: Ionic 3 mobile we

joaomh/curso-de-matlab

断牙刷新位置时间（断牙属性及刷新位置介绍

CVE-2022-34114

rugk/mastodon-simplified-federation: Sim

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053