C++ HAL_I2C_GetError函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中HAL_I2C_GetError函数的典型用法代码示例。如果您正苦于以下问题：C++ HAL_I2C_GetError函数的具体用法？C++ HAL_I2C_GetError怎么用？C++ HAL_I2C_GetError使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了HAL_I2C_GetError函数的18个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: readFrom

static void readFrom(uint8_t address, uint8_t num) {
  // address to read from
  aTxBuffer[0] = address;

  /*##-2- Start the transmission process #####################################*/
  /* While the I2C in reception process, user can transmit data through
     "aTxBuffer" buffer */
  while(HAL_I2C_Master_Transmit_DMA(&I2cHandle, I2C_ADDRESS << 1, (uint8_t*)aTxBuffer, 1)!= HAL_OK)
  {
    /* Error_Handler() function is called when Timeout error occurs.
       When Acknowledge failure occurs (Slave don't acknowledge it's address)
       Master restarts communication */
    if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
    {
      Error_Handler();
    }
  }

  /*##-3- Wait for the end of the transfer ###################################*/
  /*  Before starting a new communication transfer, you need to check the current
      state of the peripheral; if it�s busy you need to wait for the end of current
      transfer before starting a new one.
      For simplicity reasons, this example is just waiting till the end of the
      transfer, but application may perform other tasks while transfer operation
      is ongoing. */
  while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
  {
  }

  // request 6 bytes from device

  /*##-4- Put I2C peripheral in reception process ############################*/
  while(HAL_I2C_Master_Receive_DMA(&I2cHandle, I2C_ADDRESS << 1, (uint8_t *)aRxBuffer, 6) != HAL_OK)
  {
    /* Error_Handler() function is called when Timeout error occurs.
       When Acknowledge failure occurs (Slave don't acknowledge it's address)
       Master restarts communication */
    if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
    {
      Error_Handler();
    }
  }

  /*##-5- Wait for the end of the transfer ###################################*/
  /*  Before starting a new communication transfer, you need to check the current
      state of the peripheral; if it�s busy you need to wait for the end of current
      transfer before starting a new one.
      For simplicity reasons, this example is just waiting till the end of the
      transfer, but application may perform other tasks while transfer operation
      is ongoing. */
  while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
  {
  }
}

开发者ID:mrsin，项目名称:STM32F429I_ITG-3200_ADXL345_DMA，代码行数:54，代码来源:main.c

示例2: test_EasterEgg

void test_EasterEgg(void)
{
	ExpanderSetbit(7,0);
	HAL_Delay(100);
	ExpanderSetbit(7,1);
	HAL_Delay(100);

	ssd1306Init(0);
	ssd1306ClearScreen();
	ssd1306Refresh();

	// I2C
	uint8_t aTxBuffer[3]; // = {control, c};
	aTxBuffer[0] = 0x0;
	aTxBuffer[1] = 0x1;
	aTxBuffer[2] = 0x5;

	uint8_t aRxBuffer[1]; // = {control, c};
	aRxBuffer[0] = 0x0;

	ssd1306ClearScreen();

	while(HAL_I2C_Master_Transmit(&hi2c1, (uint16_t)0x50<<1, (uint8_t*)aTxBuffer, 3, 10000)!= HAL_OK)
	{
	  /* Error_Handler() function is called when Timout error occurs.
		 When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
		 Master restarts communication */
	  if (HAL_I2C_GetError(&hi2c1) != HAL_I2C_ERROR_AF)
	  {
		  ssd1306PrintInt(10,  15, "Bad Send", 0, &Font_5x8);
	  }

	}

	while(HAL_I2C_Master_Receive(&hi2c1, (uint16_t)0x50<<1, (uint8_t*)aRxBuffer, 1, 10000)!= HAL_OK)
	{
	  /* Error_Handler() function is called when Timout error occurs.
		 When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
		 Master restarts communication */
	  if (HAL_I2C_GetError(&hi2c1) != HAL_I2C_ERROR_AF)
	  {
		  ssd1306PrintInt(10,  25, "Bad recv", 0, &Font_5x8);
	  }

	}

	ssd1306PrintInt(10,  35, "Fini : ", aRxBuffer[0], &Font_5x8);
	ssd1306Refresh();

}

开发者ID:BGCX261，项目名称:zhonx3-svn-to-git，代码行数:50，代码来源:tests.c

示例3: initMPU

int initMPU(void){
	int initOkay = -1;
	HAL_I2C_StateTypeDef state;
	uint8_t tempByte = 13;
	uint8_t buffer[10] = {0,0,0,0,0,0,0,0,0,0};
	hnd.Instance = I2C1;
	hnd.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT;
	hnd.Init.ClockSpeed	= 400000;
	hnd.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
	hnd.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
	hnd.Init.DutyCycle = I2C_DUTYCYCLE_2;
	hnd.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE;
	hnd.Init.OwnAddress1 = 0x00;
	
	HAL_I2C_Init(&hnd);
	__HAL_I2C_ENABLE(&hnd);
	state = HAL_I2C_GetState(&hnd); 
	if(state == HAL_I2C_STATE_READY){
		initOkay = 0;
	}
	buffer[0]=MPU6050_RA_PWR_MGMT_1;
	buffer[1]=0x80;
	printf("READ: %u",SCCB_Read(MPU6050_RA_WHO_AM_I));
	printf("error: %u",HAL_I2C_GetError(&hnd));
	return initOkay;

}

开发者ID:RageFlo，项目名称:QuadSTM32，代码行数:27，代码来源:I2C_Treiber.c

示例4: AP_ReadBuffer

void AP_ReadBuffer(uint8_t RegAddr, uint8_t *aRxBuffer, uint8_t RXBUFFERSIZE)
{
    /* -> Lets ask for register's address */
    AP_WriteBuffer(&RegAddr, 1);
 
    /* -> Put I2C peripheral in reception process */
    while(HAL_I2C_Master_Receive(&AP_I2C_HANDLE, AP_I2C_ADDR, aRxBuffer, (uint16_t)RXBUFFERSIZE, (uint32_t)1000) != HAL_OK)
    {
        /* Error_Handler() function is called when Timeout error occurs.
         * When Acknowledge failure occurs (Slave don't acknowledge it's address)
         * Master restarts communication
         */
        if (HAL_I2C_GetError(&AP_I2C_HANDLE) != HAL_I2C_ERROR_AF)
        {
            //DEBUG(3, "In I2C::WriteBuffer -> error");
            //Error_Handler(4);
					PUTZ_ASSERT(false);
        }
    }
 
    /* -> Wait for the end of the transfer */
    /* Before starting a new communication transfer, you need to check the current
     * state of the peripheral; if it’s busy you need to wait for the end of current
     * transfer before starting a new one.
     * For simplicity reasons, this example is just waiting till the end of the
     * transfer, but application may perform other tasks while transfer operation
     * is ongoing.
     **/
    while (HAL_I2C_GetState(&AP_I2C_HANDLE) != HAL_I2C_STATE_READY)
    {
    }
}

开发者ID:decouto，项目名称:Stretchtech，代码行数:32，代码来源:Putz01.cpp

示例5: AP_WriteBuffer

void AP_WriteBuffer(uint8_t *aTxBuffer, uint8_t TXBUFFERSIZE) 
{
    /* -> Start the transmission process */
    /* While the I2C in reception process, user can transmit data through "aTxBuffer" buffer */
    while(HAL_I2C_Master_Transmit(&AP_I2C_HANDLE, AP_I2C_ADDR, (uint8_t*)aTxBuffer, (uint16_t)TXBUFFERSIZE, (uint32_t)1000)!= HAL_OK)
    {
        /*
         * Error_Handler() function is called when Timeout error occurs.
         * When Acknowledge failure occurs (Slave don't acknowledge it's address)
         * Master restarts communication
         */
 
        if (HAL_I2C_GetError(&AP_I2C_HANDLE) != HAL_I2C_ERROR_AF)
        {
            //DEBUG(3, "In I2C::WriteBuffer -> error");
            //Error_Handler(3);
        }
 
    }
 
    /* -> Wait for the end of the transfer */
    /* Before starting a new communication transfer, you need to check the current
     * state of the peripheral; if it’s busy you need to wait for the end of current
     * transfer before starting a new one.
     * For simplicity reasons, this example is just waiting till the end of the
     * transfer, but application may perform other tasks while transfer operation
     * is ongoing.
     */
      while (HAL_I2C_GetState(&AP_I2C_HANDLE) != HAL_I2C_STATE_READY)
      {
      }
}

开发者ID:decouto，项目名称:Stretchtech，代码行数:32，代码来源:Putz01.cpp

示例6: i2c_send1

void i2c_send1(void)
{
    char buf[] = {0x00, 0x00};
    if(HAL_I2C_Master_Transmit(&hi2c, (uint16_t)0xAE, (uint8_t*)buf, 2, 10000) != HAL_OK)
    {
        if (HAL_I2C_GetError(&hi2c) != HAL_I2C_ERROR_AF)
        {
            led_on();
            return;
        }
    }
    while(HAL_I2C_Master_Receive(&hi2c, (uint16_t)0xAF, (uint8_t *)buf, 2, 10000) != HAL_OK)
    {
        if (HAL_I2C_GetError(&hi2c) != HAL_I2C_ERROR_AF)
        {
            led_on();
            return;
        }
    }
}

开发者ID:minhtran612，项目名称:stm32f4，代码行数:20，代码来源:i2c.c

示例7: mma8652Reg8Writre

static void mma8652Reg8Writre (I2C_HandleTypeDef *i2cHandle, uint8_t reg, uint8_t value)
{
        uint8_t txBuffer[2] = {reg, value};

        while (HAL_I2C_Master_Transmit (i2cHandle, (uint8_t) MMA8652_I2C_ADDR, (uint8_t*) txBuffer, sizeof(txBuffer), 10000) != HAL_OK) {
                /* Error_Handler() function is called when Timeout error occurs.
                 When Acknowledge failure occurs (Slave don't acknowledge it's address)
                 Master restarts communication */
                if (HAL_I2C_GetError (i2cHandle) != HAL_I2C_ERROR_AF) {
                        Error_Handler ();
                }
        }
}

开发者ID:iwasz，项目名称:stm32-mma8652，代码行数:13，代码来源:mma8652.c

示例8: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F3xx HAL library initialization:
       - Configure the Flash prefetch
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Set NVIC Group Priority to 4
       - Low Level Initialization
     */
  HAL_Init();
  
  /* Configure the system clock to 72 MHz */
  SystemClock_Config();
  
  /* Configure LED7, LED3 and LED9*/
  BSP_LED_Init(LED7);
  BSP_LED_Init(LED3);
  BSP_LED_Init(LED9);
  
  /*##-1- Configure the I2C peripheral ######################################*/
  I2cHandle.Instance             = I2Cx;
  
  I2cHandle.Init.Timing          = I2C_TIMING;
  I2cHandle.Init.OwnAddress1     = I2C_ADDRESS;
  I2cHandle.Init.AddressingMode  = I2C_ADDRESSINGMODE_7BIT;
  I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLED;
  I2cHandle.Init.OwnAddress2     = 0xFF;
  I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLED;
  I2cHandle.Init.NoStretchMode   = I2C_NOSTRETCH_DISABLED;  
  
  if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();    
  }

  /* Enable the Analog I2C Filter */
  HAL_I2CEx_AnalogFilter_Config(&I2cHandle,I2C_ANALOGFILTER_ENABLED);
  
#ifdef MASTER_BOARD
  
  /* Configure USER Button*/
  BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);

  /* Wait for USER Button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
  {
  }
  
  /* Wait for USER Button release before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
  {
  }
  
  /* The board sends the message and expects to receive it back */
  
  /*##-2- Start the transmission process #####################################*/  
  /* While the I2C in reception process, user can transmit data through 
     "aTxBuffer" buffer */
  while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
  {
    /* Error_Handler() function is called when Timout error occurs.
       When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
       Master restarts communication */
    if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
    {
      Error_Handler();
    }
  }
  
  /*##-3- Wait for the end of the transfer ###################################*/  
  /*  Before starting a new communication transfer, you need to check the current   
      state of the peripheral; if it’s busy you need to wait for the end of current
      transfer before starting a new one.
      For simplicity reasons, this example is just waiting till the end of the 
      transfer, but application may perform other tasks while transfer operation
      is ongoing. */  
  while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
  {
  } 
  
  /* Wait for USER Button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
  {
  }

  /* Wait for USER Button release before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
  {
  }

  /*##-4- Put I2C peripheral in reception process ###########################*/  
//.........这里部分代码省略.........

开发者ID:GreyCardinalRus，项目名称:stm32-cube，代码行数:101，代码来源:main.c

示例9: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{    
  /* STM32L0xx HAL library initialization:
       - Configure the Flash prefetch, Flash preread and Buffer caches
       - Systick timer is configured by default as source of time base, but user 
             can eventually implement his proper time base source (a general purpose 
             timer for example or other time source), keeping in mind that Time base 
             duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
             handled in milliseconds basis.
       - Low Level Initialization
     */
  HAL_Init();
  
  /* Configure LED3 and LED4 */
  BSP_LED_Init(LED3);
  BSP_LED_Init(LED4);
  /* Configure the system clock to 32 Mhz */
  SystemClock_Config();

  /*##-1- Configure the I2C peripheral #######################################*/
  I2CxHandle.Instance              = I2Cx;
  I2CxHandle.Init.AddressingMode   = I2C_ADDRESSINGMODE_10BIT;
  I2CxHandle.Init.Timing           = I2C_TIMING_400KHZ;
  I2CxHandle.Init.DualAddressMode  = I2C_DUALADDRESS_DISABLED;
  I2CxHandle.Init.OwnAddress2Masks = I2C_OA2_NOMASK;
  I2CxHandle.Init.GeneralCallMode  = I2C_GENERALCALL_DISABLED;
  I2CxHandle.Init.NoStretchMode    = I2C_NOSTRETCH_DISABLED;
  I2CxHandle.Init.OwnAddress1      = I2C_ADDRESS;
  I2CxHandle.Init.OwnAddress2      = 0xFE;
  if(HAL_I2C_Init(&I2CxHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();    
  }
  
#ifdef MASTER_BOARD
  
  /* Configure User Button */
  BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
  
  /* Wait for User Button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) != 1)
  {
  }
  
  /* Wait for User Button release before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) != 0)
  {
  }
  
  /* The board sends the message and expects to receive it back */
  
  /*##-2- Start the transmission process #####################################*/  
  /* While the I2C in reception process, user can transmit data through 
     "aTxBuffer" buffer */
  while(HAL_I2C_Master_Transmit_DMA(&I2CxHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
  {
    /* Error_Handler() function is called when Timout error occurs.
       When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
       Master restarts communication */
    if (HAL_I2C_GetError(&I2CxHandle) != HAL_I2C_ERROR_AF)
    {
      Error_Handler();
    }
  }
  
  /*##-3- Wait for the end of the transfer ###################################*/  
  /*  Before starting a new communication transfer, you need to check the current   
      state of the peripheral; if it’s busy you need to wait for the end of current
      transfer before starting a new one.
      For simplicity reasons, this example is just waiting till the end of the 
      transfer, but application may perform other tasks while transfer operation
      is ongoing. */  
  while (HAL_I2C_GetState(&I2CxHandle) != HAL_I2C_STATE_READY)
  {
  } 
  
  /* Wait for User Button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) != 1)
  {
  }

  /* Wait for User Button release before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) != 0)
  {
  }
  
  /*##-4- Put I2C peripheral in reception process ###########################*/  
  while(HAL_I2C_Master_Receive_DMA(&I2CxHandle, (uint16_t)I2C_ADDRESS, (uint8_t *)aRxBuffer, RXBUFFERSIZE) != HAL_OK)
  {
    /* Error_Handler() function is called when Timout error occurs.
       When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
       Master restarts communication */
    if (HAL_I2C_GetError(&I2CxHandle) != HAL_I2C_ERROR_AF)
    {
//.........这里部分代码省略.........

开发者ID:shjere，项目名称:common，代码行数:101，代码来源:main.c

示例10: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
    sAPP_PIXARM_READ_DATA* data;
    sAPP_PIXARM_READ_REQ* req;
    uint8_t iter = 1;
    HAL_StatusTypeDef stat;
    
    /* STM32F4xx HAL library initialization:
        - Configure the Flash prefetch, instruction and Data caches
        - Configure the Systick to generate an interrupt each 1 msec
        - Set NVIC Group Priority to 4
        - Global MSP (MCU Support Package) initialization
        */
    HAL_Init();
    
    /* Configure LED4, LED5 and LED6 */
    BSP_LED_Init(LED4);
    BSP_LED_Init(LED5);
    BSP_LED_Init(LED6);
    BSP_LED_Init(LED3);
    
    /* Configure the system clock to 168 MHz */
    SystemClock_Config();
    
    /*##-1- Configure the I2C peripheral ######################################*/
    I2cHandle.Instance             = I2Cx;
    
    I2cHandle.Init.AddressingMode  = I2C_ADDRESSINGMODE_7BIT;
    I2cHandle.Init.ClockSpeed      = 400000;
    I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
    I2cHandle.Init.DutyCycle       = I2C_DUTYCYCLE_16_9;
    I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
    I2cHandle.Init.NoStretchMode   = I2C_NOSTRETCH_DISABLE;
    I2cHandle.Init.OwnAddress1     = I2C_ADDRESS;
    I2cHandle.Init.OwnAddress2     = 0x0;
    
    if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
    {
        /* Initialization Error */
        Error_Handler();    
    }
    
    Test_Log_Init();
    
    /* Configure USER Button */
    BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
    
    /* Wait for USER Button press before starting the Communication */
    while (BSP_PB_GetState(BUTTON_KEY) != 1)
    {
    }
    
    /* Wait for USER Button release before starting the Communication */
    while (BSP_PB_GetState(BUTTON_KEY) != 0)
    {
    }
    
    BSP_LED_On(LED3);
    BSP_LED_Off(LED6);
    BSP_LED_Off(LED4);
    
    /* The board sends the message and expects to receive it back */
    Test_Log("Starting I2C Handshake.\r\n");
    
    /*##-2- Start the transmission process #####################################*/  
    /* Timeout is set to 10S */
    while(HAL_I2C_Master_Transmit(&I2cHandle, (uint16_t)I2C_ADDRESS, aTxBuffer, TXBUFFERSIZE, 10000)!= HAL_OK)
    {
        /* Error_Handler() function is called when Timeout error occurs.
        When Acknowledge failure occurs (Slave don't acknowledge it's address)
        Master restarts communication */
        if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
        {
            Error_Handler();
        }
    }
    
    
    
    /*##-3- Put I2C peripheral in reception process ############################*/ 
    /* Timeout is set to 10S */ 
    while((stat = HAL_I2C_Master_Receive(&I2cHandle, (uint16_t)I2C_ADDRESS, aRxBuffer, RXBUFFERSIZE, 10000)) != HAL_OK)
    {
        /* Error_Handler() function is called when Timeout error occurs.
        When Acknowledge failure occurs (Slave don't acknowledge it's address)
        Master restarts communication */
        if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
        {
        Error_Handler();
        }   
    }
    
    /* Turn LED6 on: Transfer in reception process is correct */
    BSP_LED_On(LED6);
    
//.........这里部分代码省略.........

开发者ID:Autonobotics，项目名称:NavigationFirmware，代码行数:101，代码来源:main.c

示例11: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F0xx HAL library initialization:
       - Configure the Flash prefetch
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Low Level Initialization
     */
  HAL_Init();
  
  /* Configure the system clock to 48 MHz */
  SystemClock_Config();

  /* Configure LED_GREEN and LED_RED */
  BSP_LED_Init(LED_GREEN);
  BSP_LED_Init(LED_RED);
  
  /*##-1- Configure the I2C peripheral ######################################*/
  I2cHandle.Instance             = I2Cx;
  
  I2cHandle.Init.Timing          = I2C_TIMING;
  I2cHandle.Init.OwnAddress1     = I2C_ADDRESS;
  I2cHandle.Init.AddressingMode  = I2C_ADDRESSINGMODE_10BIT;
  I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
  I2cHandle.Init.OwnAddress2     = 0xFF;
  I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
  I2cHandle.Init.NoStretchMode   = I2C_NOSTRETCH_DISABLE;  
  
  if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();    
  }

  /* Enable the Analog I2C Filter */
  HAL_I2CEx_ConfigAnalogFilter(&I2cHandle,I2C_ANALOGFILTER_ENABLE);

#ifdef MASTER_BOARD
  
  /* Configure User Button*/
  BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);

  /* Wait for User Button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
  {
  }
  
  /* Wait for User Button release before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
  {
  }
  
  /* The board sends the message and expects to receive it back */
  
  /*##-2- Start the transmission process #####################################*/  
  /* While the I2C in reception process, user can transmit data through 
     "aTxBuffer" buffer */
  /* Timeout is set to 10S */
  while(HAL_I2C_Master_Transmit(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE, 10000)!= HAL_OK)
  {
    /* Error_Handler() function is called when Timout error occurs.
       When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
       Master restarts communication */
    if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
    {
      Error_Handler();
    }
  }
  
  /* Turn LED_GREEN on: Transfer in Transmission process is correct */
  BSP_LED_On(LED_GREEN);

  /* Wait for User Button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
  {
  }
  
  /* Wait for User Button release before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
  {
  }

  /*##-3- Put I2C peripheral in reception process ############################*/ 
  /* Timeout is set to 10S */ 
  while(HAL_I2C_Master_Receive(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 10000) != HAL_OK)
  {
    /* Error_Handler() function is called when Timout error occurs.
       When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
       Master restarts communication */
    if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
    {
      Error_Handler();
//.........这里部分代码省略.........

开发者ID:NjordCZ，项目名称:stm32cubef0，代码行数:101，代码来源:main.c

示例12: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F103xG HAL library initialization:
       - Configure the Flash prefetch
       - Systick timer is configured by default as source of time base, but user 
         can eventually implement his proper time base source (a general purpose 
         timer for example or other time source), keeping in mind that Time base 
         duration should be kept 1ms since PPP_TIMEOUT_VALUEs are defined and 
         handled in milliseconds basis.
       - Set NVIC Group Priority to 4
       - Low Level Initialization
     */
  HAL_Init();
  
  /* Configure the system clock to 72 MHz */
  SystemClock_Config();
  
  /* Configure LED1 and LED3 */
  BSP_LED_Init(LED1);
  BSP_LED_Init(LED3);
  

  /*##-1- Configure the I2C peripheral ######################################*/
  I2cHandle.Instance             = I2Cx;
  I2cHandle.Init.ClockSpeed      = I2C_SPEEDCLOCK;
  I2cHandle.Init.DutyCycle       = I2C_DUTYCYCLE;
  I2cHandle.Init.OwnAddress1     = I2C_ADDRESS;
  I2cHandle.Init.AddressingMode  = I2C_ADDRESSINGMODE_7BIT;
  I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
  I2cHandle.Init.OwnAddress2     = 0xFF;
  I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
  I2cHandle.Init.NoStretchMode   = I2C_NOSTRETCH_DISABLE;  
  
  if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }
  

#ifdef MASTER_BOARD
  
  /* Configure Key push-button */
  BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);

  /* Wait for Key push-button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) != GPIO_PIN_RESET)
  {
  }
  
  /* Wait for Key push-button release before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) != GPIO_PIN_SET)
  {
  }

  while(1)
  {
    /* Initialize number of data variables */
    hTxNumData = TXBUFFERSIZE;
    hRxNumData = RXBUFFERSIZE;

    /* Update bTransferRequest to send buffer write request for Slave */
    bTransferRequest = MASTER_REQ_WRITE;

    /*##-2- Master sends write request for slave #############################*/
    while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)&bTransferRequest, 1)!= HAL_OK)
    {
      /* Error_Handler() function is called when Timeout error occurs.
         When Acknowledge failure occurs (Slave don't acknowledge its address)
         Master restarts communication */
      if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
      {
        Error_Handler();
      }
    }

    /*  Before starting a new communication transfer, you need to check the current
    state of the peripheral; if it’s busy you need to wait for the end of current
    transfer before starting a new one.
    For simplicity reasons, this example is just waiting till the end of the
    transfer, but application may perform other tasks while transfer operation
    is ongoing. */
    while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
    {
    }

    /*##-3- Master sends number of data to be written ########################*/
    while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)&hTxNumData, 2)!= HAL_OK)
    {
      /* Error_Handler() function is called when Timeout error occurs.
         When Acknowledge failure occurs (Slave don't acknowledge its address)
         Master restarts communication */
      if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
      {
        Error_Handler();
//.........这里部分代码省略.........

开发者ID:NjordCZ，项目名称:STM32Cube_FW_F1，代码行数:101，代码来源:main.c

示例13: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{

    /* STM32F3xx HAL library initialization:
         - Configure the Flash prefetch
         - Configure the Systick to generate an interrupt each 1 msec
         - Set NVIC Group Priority to 4
         - Low Level Initialization
       */
    HAL_Init();

    /* Configure the system clock to 64 MHz */
    SystemClock_Config();

    /* Configure LED1 and LED3 */
    BSP_LED_Init(LED1);
    BSP_LED_Init(LED3);


    /*##-1- Configure the I2C peripheral ######################################*/
    I2cHandle.Instance             = I2Cx;
    I2cHandle.Init.Timing          = I2C_TIMING;
    I2cHandle.Init.OwnAddress1     = I2C_ADDRESS;
    I2cHandle.Init.AddressingMode  = I2C_ADDRESSINGMODE_10BIT;
    I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
    I2cHandle.Init.OwnAddress2     = 0xFF;
    I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
    I2cHandle.Init.NoStretchMode   = I2C_NOSTRETCH_DISABLE;

    if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
    {
        /* Initialization Error */
        Error_Handler();
    }

    /* Enable the Analog I2C Filter */
    HAL_I2CEx_ConfigAnalogFilter(&I2cHandle,I2C_ANALOGFILTER_ENABLE);

#ifdef MASTER_BOARD

    /* Configure User push-button button */
    BSP_PB_Init(BUTTON_USER,BUTTON_MODE_GPIO);

    /* Wait for User push-button press before starting the Communication */
    while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
    {
    }

    /* Delay to avoid that possible signal rebound is taken as button release */
    HAL_Delay(50);

    /* Wait for User push-button release before starting the Communication */
    while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
    {
    }


    /* The board sends the message and expects to receive it back */

    /*##-2- Start the transmission process #####################################*/
    /* While the I2C in reception process, user can transmit data through
       "aTxBuffer" buffer */
    while(HAL_I2C_Master_Transmit_IT(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE)!= HAL_OK)
    {
        /* Error_Handler() function is called when Timeout error occurs.
           When Acknowledge failure occurs (Slave don't acknowledge its address)
           Master restarts communication */
        if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
        {
            Error_Handler();
        }
    }

    /*##-3- Wait for the end of the transfer ###################################*/
    /*  Before starting a new communication transfer, you need to check the current
        state of the peripheral; if it’s busy you need to wait for the end of current
        transfer before starting a new one.
        For simplicity reasons, this example is just waiting till the end of the
        transfer, but application may perform other tasks while transfer operation
        is ongoing. */
    while (HAL_I2C_GetState(&I2cHandle) != HAL_I2C_STATE_READY)
    {
    }

    /* Wait for User push-button press before starting the Communication */
    while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
    {
    }

    /* Delay to avoid that possible signal rebound is taken as button release */
    HAL_Delay(50);

    /* Wait for User push-button release before starting the Communication */
    while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
    {
//.........这里部分代码省略.........

开发者ID:PaxInstruments，项目名称:STM32CubeF3，代码行数:101，代码来源:main.c

示例14: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F2xx HAL library initialization:
       - Configure the Flash prefetch, instruction and Data caches
       - Configure the Systick to generate an interrupt each 1 msec
       - Set NVIC Group Priority to 4
       - Global MSP (MCU Support Package) initialization
     */
  HAL_Init();
  
  /* Configure LED1 and LED2 */
  BSP_LED_Init(LED1);
  BSP_LED_Init(LED2);
  
  /* Configure the system clock to 120 MHz */
  SystemClock_Config();

  /*##-1- Configure the I2C peripheral #######################################*/
  I2CxHandle.Instance             = I2Cx;
  I2CxHandle.Init.AddressingMode  = I2C_ADDRESSINGMODE_7BIT;
  I2CxHandle.Init.ClockSpeed      = 400000;
  I2CxHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLED;
  I2CxHandle.Init.DutyCycle       = I2C_DUTYCYCLE_16_9;
  I2CxHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLED;
  I2CxHandle.Init.NoStretchMode   = I2C_NOSTRETCH_DISABLED;
  I2CxHandle.Init.OwnAddress1     = I2C_ADDRESS;
  I2CxHandle.Init.OwnAddress2     = 0;

  if(HAL_I2C_Init(&I2CxHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }

#ifdef MASTER_BOARD
  /* Configure User Button */
  BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);

  /* Wait for User Button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) != 1)
  {
  }

  /* Wait for User Button release before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) != 0)
  {
  }

  while(1)
  {
    /* Initialize number of data variables */
    hTxNumData = TXBUFFERSIZE;
    hRxNumData = RXBUFFERSIZE;

    /* Update bTransferRequest to send buffer write request for Slave */
    bTransferRequest = MASTER_REQ_WRITE;

    /*##-2- Master sends write request for slave #############################*/
    while(HAL_I2C_Master_Transmit_IT(&I2CxHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)&bTransferRequest, 1)!= HAL_OK)
    {
      /* Error_Handler() function is called when Timout error occurs.
         When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
         Master restarts communication */
      if (HAL_I2C_GetError(&I2CxHandle) != HAL_I2C_ERROR_AF)
      {
        Error_Handler();
      }
    }

    /*  Before starting a new communication transfer, you need to check the current
    state of the peripheral; if it’s busy you need to wait for the end of current
    transfer before starting a new one.
    For simplicity reasons, this example is just waiting till the end of the
    transfer, but application may perform other tasks while transfer operation
    is ongoing. */
    while (HAL_I2C_GetState(&I2CxHandle) != HAL_I2C_STATE_READY)
    {
    }

    /*##-3- Master sends number of data to be written ########################*/
    while(HAL_I2C_Master_Transmit_IT(&I2CxHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)&hTxNumData, 2)!= HAL_OK)
    {
      /* Error_Handler() function is called when Timout error occurs.
         When Acknowledge failure ocucurs (Slave don't acknowledge it's address)
         Master restarts communication */
      if (HAL_I2C_GetError(&I2CxHandle) != HAL_I2C_ERROR_AF)
      {
        Error_Handler();
      }
    }

    /*  Before starting a new communication transfer, you need to check the current
    state of the peripheral; if it’s busy you need to wait for the end of current
    transfer before starting a new one.
    For simplicity reasons, this example is just waiting till the end of the
//.........这里部分代码省略.........

开发者ID:GreyCardinalRus，项目名称:stm32-cube，代码行数:101，代码来源:main.c

示例15: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F3xx HAL library initialization:
       - Configure the Flash prefetch
       - Configure the Systick to generate an interrupt each 1 msec
       - Set NVIC Group Priority to 4
       - Low Level Initialization
     */
  HAL_Init();
  
  /* Configure LED2 */
  BSP_LED_Init(LED2);
  
  /* Configure the system clock to 64 MHz */
  SystemClock_Config();

  /*##-1- Configure the I2C peripheral ######################################*/
  I2cHandle.Instance             = I2Cx;
  I2cHandle.Init.Timing          = I2C_TIMING;
  I2cHandle.Init.OwnAddress1     = I2C_ADDRESS;
  I2cHandle.Init.AddressingMode  = I2C_ADDRESSINGMODE_10BIT;
  I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLED;
  I2cHandle.Init.OwnAddress2     = 0xFF;
  I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLED;
  I2cHandle.Init.NoStretchMode   = I2C_NOSTRETCH_DISABLED;  
  
  if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }
  
  /* Enable the Analog I2C Filter */
  HAL_I2CEx_AnalogFilter_Config(&I2cHandle,I2C_ANALOGFILTER_ENABLED);

#ifdef MASTER_BOARD
  
  /* Configure User push-button */
  BSP_PB_Init(BUTTON_USER, BUTTON_MODE_GPIO);

  /* Wait for User push-button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
  {
  }
  
  /* Wait for User push-button release before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
  {
  }
  
  /* The board sends the message and expects to receive it back */
  
  /*##-2- Start the transmission process #####################################*/  
  /* While the I2C in reception process, user can transmit data through 
     "aTxBuffer" buffer */
  /* Timeout is set to 10S */
  while(HAL_I2C_Master_Transmit(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE, 10000)!= HAL_OK)
  {
    /* Error_Handler() function is called when Timeout error occurs.
       When Acknowledge failure occurs (Slave don't acknowledge its address)
       Master restarts communication */
    if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
    {
      Error_Handler();
    }
  }
  
  /* Turn LED2 on: Transfer in Transmission process is correct */
  BSP_LED_On(LED2);

  /* Wait for User push-button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_RESET)
  {
  }
  
  /* Wait for User push-button release before starting the Communication */
  while (BSP_PB_GetState(BUTTON_USER) != GPIO_PIN_SET)
  {
  }

  /*##-3- Put I2C peripheral in reception process ############################*/ 
  /* Timeout is set to 10S */ 
  while(HAL_I2C_Master_Receive(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 10000) != HAL_OK)
  {
    /* Error_Handler() function is called when Timeout error occurs.
       When Acknowledge failure occurs (Slave don't acknowledge it's address)
       Master restarts communication */
    if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
    {
      Error_Handler();
    }
  }
  
  /* Turn LED2 off: Transfer in reception process is correct */
  BSP_LED_Off(LED2);
//.........这里部分代码省略.........

开发者ID:afconsult-south，项目名称:dragonfly-fcb，代码行数:101，代码来源:main.c

示例16: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{
  /* STM32F4xx HAL library initialization:
       - Configure the Flash prefetch, instruction and Data caches
       - Configure the Systick to generate an interrupt each 1 msec
       - Set NVIC Group Priority to 4
       - Global MSP (MCU Support Package) initialization
     */
  HAL_Init();

  /* Configure LED3 and LED4 */
  BSP_LED_Init(LED3);
  BSP_LED_Init(LED4);

  /* Configure the system clock to 168 MHz */
  SystemClock_Config();

  /*##-1- Configure the I2C peripheral #######################################*/
  I2cHandle.Instance             = I2Cx;

  I2cHandle.Init.AddressingMode  = I2C_ADDRESSINGMODE_10BIT;
  I2cHandle.Init.ClockSpeed      = 400000;
  I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
  I2cHandle.Init.DutyCycle       = I2C_DUTYCYCLE_16_9;
  I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
  I2cHandle.Init.NoStretchMode   = I2C_NOSTRETCH_DISABLE;
  I2cHandle.Init.OwnAddress1     = I2C_ADDRESS;
  I2cHandle.Init.OwnAddress2     = 0xFE;

  if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();
  }

#ifdef MASTER_BOARD

  /* Configure USER Button */
  BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);

  /* Wait for USER Button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) != 1)
  {
  }

  /* Wait for USER Button release before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) != 0)
  {
  }

  /* The board sends the message and expects to receive it back */

  /*##-2- Start the transmission process #####################################*/
  /* While the I2C in reception process, user can transmit data through
     "aTxBuffer" buffer */
  /* Timeout is set to 10S */
  while(HAL_I2C_Master_Transmit(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t*)aTxBuffer, TXBUFFERSIZE, 10000)!= HAL_OK)
  {
    /* Error_Handler() function is called when Timeout error occurs.
       When Acknowledge failure occurs (Slave don't acknowledge it's address)
       Master restarts communication */
    if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
    {
      Error_Handler();
    }
  }

  /* Turn LED3 on: Transfer in Transmission process is correct */
  BSP_LED_On(LED3);

  /* Wait for USER Button press before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) != 1)
  {
  }

  /* Wait for USER Button release before starting the Communication */
  while (BSP_PB_GetState(BUTTON_KEY) != 0)
  {
  }

  /*##-3- Put I2C peripheral in reception process ############################*/
  /* Timeout is set to 10S */
  while(HAL_I2C_Master_Receive(&I2cHandle, (uint16_t)I2C_ADDRESS, (uint8_t *)aRxBuffer, RXBUFFERSIZE, 10000) != HAL_OK)
  {
    /* Error_Handler() function is called when Timeout error occurs.
       When Acknowledge failure occurs (Slave don't acknowledge it's address)
       Master restarts communication */
    if (HAL_I2C_GetError(&I2cHandle) != HAL_I2C_ERROR_AF)
    {
      Error_Handler();
    }
  }

  /* Turn LED3 off: Transfer in reception process is correct */
  BSP_LED_Off(LED3);
//.........这里部分代码省略.........

开发者ID:Joe-Merten，项目名称:Stm32-Tools-Evaluation，代码行数:101，代码来源:main.c

示例17: main

/**
  * @brief  Main program
  * @param  None
  * @retval None
  */
int main(void)
{    
  /* STM32F4xx HAL library initialization:
       - Configure the Flash prefetch, instruction and Data caches
       - Configure the Systick to generate an interrupt each 1 msec
       - Set NVIC Group Priority to 4
       - Global MSP (MCU Support Package) initialization
     */
  HAL_Init();
  
  /* Configure LED4, LED5 and LED6 */
  BSP_LED_Init(LED4);
  BSP_LED_Init(LED5);
  BSP_LED_Init(LED6);

  /* Configure the system clock to 84 MHz */
  SystemClock_Config();

  /*##-1- Configure the I2C peripheral ######################################*/
  I2cHandle.Instance             = I2Cx;
  
  I2cHandle.Init.AddressingMode  = I2C_ADDRESSINGMODE_10BIT;
  I2cHandle.Init.ClockSpeed      = 400000;
  I2cHandle.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE;
  I2cHandle.Init.DutyCycle       = I2C_DUTYCYCLE_16_9;
  I2cHandle.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE;
  I2cHandle.Init.NoStretchMode   = I2C_NOSTRETCH_DISABLE;
  I2cHandle.Init.OwnAddress1     = I2C_ADDRESS;
  I2cHandle.Init.OwnAddress2     = 0xFE;
  
  if(HAL_I2C_Init(&I2cHandle) != HAL_OK)
  {
    /* Initialization Error */
    Error_Handler();    
  }
  
#ifdef MASTER_BOARD
  
  /* Configure User Button */
  BSP_PB_Init(BUTTON_KEY, BUTTON_MODE_GPIO);
  
  /* Wait for Us

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ HAL_I2C_GetState函数代码示例发布时间：2022-05-30

C++ HAL_HCD_Init函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：18268|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9677|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8177|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8548|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8457|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9388|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8427|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7862|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8411|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7394|2022-11-06

客服电话

电子邮件

C++ HAL_I2C_GetError函数代码示例

示例1: readFrom

示例2: test_EasterEgg

示例3: initMPU

示例4: AP_ReadBuffer

示例5: AP_WriteBuffer

示例6: i2c_send1

示例7: mma8652Reg8Writre

示例8: main

示例9: main

示例10: main

示例11: main

示例12: main

示例13: main

示例14: main

示例15: main

示例16: main

示例17: main

请发表评论

全部评论

上一篇：

下一篇：

bradtraversy/iweather: Ionic 3 mobile we

joaomh/curso-de-matlab

断牙刷新位置时间（断牙属性及刷新位置介绍

CVE-2022-34114

rugk/mastodon-simplified-federation: Sim

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053