C++ HAL_PCD_Init函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中HAL_PCD_Init函数的典型用法代码示例。如果您正苦于以下问题：C++ HAL_PCD_Init函数的具体用法？C++ HAL_PCD_Init怎么用？C++ HAL_PCD_Init使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了HAL_PCD_Init函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_Init(USBD_HandleTypeDef *pdev)
{
#ifdef USE_USB_FS
  /* Set LL Driver parameters */
  hpcd.Instance = USB_OTG_FS;
  hpcd.Init.dev_endpoints = 4;
  hpcd.Init.use_dedicated_ep1 = 0;
  hpcd.Init.ep0_mps = 0x40;
  hpcd.Init.dma_enable = 0;
  hpcd.Init.low_power_enable = 0;
  hpcd.Init.phy_itface = PCD_PHY_EMBEDDED;
  hpcd.Init.Sof_enable = 0;
  hpcd.Init.speed = PCD_SPEED_FULL;
  hpcd.Init.vbus_sensing_enable = 1;
  hpcd.Init.lpm_enable = 0;
  
  /* Link The driver to the stack */
  hpcd.pData = pdev;
  pdev->pData = &hpcd;
  
  /* Initialize LL Driver */
  HAL_PCD_Init(&hpcd);
  
  HAL_PCDEx_SetRxFiFo(&hpcd, 0xA0);
  HAL_PCDEx_SetTxFiFo(&hpcd, 0, 0xA0);
#endif
  
#ifdef USE_USB_HS
  /* Set LL Driver parameters */
  hpcd.Instance = USB_OTG_HS;
  hpcd.Init.dev_endpoints = 6;
  hpcd.Init.use_dedicated_ep1 = 0;
  hpcd.Init.ep0_mps = 0x40;
  
  /* Be aware that enabling DMA mode will result in data being sent only by
  multiple of 4 packet sizes. This is due to the fact that USB DMA does
  not allow sending data from non word-aligned addresses.
  For this specific application, it is advised to not enable this option
  unless required. */
  hpcd.Init.dma_enable = 0;
  hpcd.Init.low_power_enable = 0;
  hpcd.Init.phy_itface = PCD_PHY_ULPI; 
  hpcd.Init.Sof_enable = 0;
  hpcd.Init.speed = PCD_SPEED_HIGH;
  hpcd.Init.vbus_sensing_enable = 1;
  hpcd.Init.lpm_enable = 0;
  
  /* Link The driver to the stack */
  hpcd.pData = pdev;
  pdev->pData = &hpcd;
  
  /* Initialize LL Driver */
  HAL_PCD_Init(&hpcd);
  
  HAL_PCDEx_SetRxFiFo(&hpcd, 0x200);
  HAL_PCDEx_SetTxFiFo(&hpcd, 0, 0x200);  
#endif 
  
  return USBD_OK;
}

开发者ID:nidhiyanandh，项目名称:STM32Cube_FW_F4_V1.5.0_GCC_Makefile，代码行数:65，代码来源:usbd_conf.c

示例2: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef  USBD_LL_Init (USBD_HandleTypeDef *pdev)
{ 
  /* Init USB_IP */
  /* Link The driver to the stack */  
  hpcd_USB_OTG_FS.pData = pdev;
  pdev->pData = &hpcd_USB_OTG_FS; 
#ifdef STM32F4
  hpcd_USB_OTG_FS.Instance = USB_OTG_FS;
  hpcd_USB_OTG_FS.Init.dev_endpoints = 4;
  hpcd_USB_OTG_FS.Init.speed = PCD_SPEED_FULL; // MUST KEEP THIS FULL - buffer sizes only big enough for this, not high
  hpcd_USB_OTG_FS.Init.dma_enable = DISABLE; // NO DMA - we are assuming USBD_CtlSendData/USBD_LL_Transmit don't keep the pointer they are passed
  hpcd_USB_OTG_FS.Init.ep0_mps = DEP0CTL_MPS_8;
  hpcd_USB_OTG_FS.Init.phy_itface = PCD_PHY_EMBEDDED;
  hpcd_USB_OTG_FS.Init.Sof_enable = ENABLE;
  hpcd_USB_OTG_FS.Init.low_power_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.lpm_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.vbus_sensing_enable = ENABLE;
  hpcd_USB_OTG_FS.Init.use_dedicated_ep1 = DISABLE;
  HAL_PCD_Init(&hpcd_USB_OTG_FS);

  // USB memory is 1.25kB - lots of room for big FIFO sizes
  HAL_PCDEx_SetRxFiFo(&hpcd_USB_OTG_FS, 0x40);
  HAL_PCDEx_SetTxFiFo(&hpcd_USB_OTG_FS, 0, 0x20); // EP0 IN
  HAL_PCDEx_SetTxFiFo(&hpcd_USB_OTG_FS, 1, 0x40); // HID IN
  HAL_PCDEx_SetTxFiFo(&hpcd_USB_OTG_FS, 2, 0x20); // CDC CMD
  HAL_PCDEx_SetTxFiFo(&hpcd_USB_OTG_FS, 3, 0x40); // CDC IN
#endif  
#ifdef STM32F1
  hpcd_USB_OTG_FS.Instance = USB;
  hpcd_USB_OTG_FS.Init.dev_endpoints = 8;
  hpcd_USB_OTG_FS.Init.speed = PCD_SPEED_FULL;
  hpcd_USB_OTG_FS.Init.ep0_mps = DEP0CTL_MPS_8;
  hpcd_USB_OTG_FS.Init.Sof_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.low_power_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.lpm_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.battery_charging_enable = DISABLE;
  HAL_PCD_Init(&hpcd_USB_OTG_FS);

  // USB memory is 512 bytes according to datasheet, so we should have loads
  // of space available?
  /*HAL_PCDEx_PMAConfig(pdev->pData , 0x00 , PCD_SNG_BUF, 0x18);
  HAL_PCDEx_PMAConfig(pdev->pData , 0x80 , PCD_SNG_BUF, 0x58);
  HAL_PCDEx_PMAConfig(pdev->pData , 0x81 , PCD_SNG_BUF, 0xC0);  // HID IN
  HAL_PCDEx_PMAConfig(pdev->pData , 0x01 , PCD_SNG_BUF, 0x110); // unused?
  HAL_PCDEx_PMAConfig(pdev->pData , 0x82 , PCD_SNG_BUF, 0x100); // CDC CMD
  HAL_PCDEx_PMAConfig(pdev->pData , 0x83 , PCD_SNG_BUF, 0x180); // CDC IN
  HAL_PCDEx_PMAConfig(pdev->pData , 0x03 , PCD_SNG_BUF, 0x1C0); // CDC OUT*/
  // above doesn't work
  HAL_PCDEx_PMAConfig(pdev->pData , 0x00 , PCD_SNG_BUF, 0x18);
  HAL_PCDEx_PMAConfig(pdev->pData , 0x80 , PCD_SNG_BUF, 0x58);
  HAL_PCDEx_PMAConfig(pdev->pData , 0x81 , PCD_SNG_BUF, 0xC0);  // CDC IN
  HAL_PCDEx_PMAConfig(pdev->pData , 0x01 , PCD_SNG_BUF, 0x110); // CDC OUT
  HAL_PCDEx_PMAConfig(pdev->pData , 0x82 , PCD_SNG_BUF, 0x100); // CDC CMD

#endif  
  return USBD_OK;
}

开发者ID:nihaopaul，项目名称:Espruino，代码行数:62，代码来源:usbd_conf.c

示例3: stm32_usbc_init

void stm32_usbc_init(void)
{
    LTRACE_ENTRY;

    usbc.pma_highwater = 0x40;

    // Set LL Driver parameters
    usbc.handle.Instance = USB;
    usbc.handle.Init.dev_endpoints = 4;
    usbc.handle.Init.ep0_mps = 0x40;
    usbc.handle.Init.phy_itface = PCD_PHY_EMBEDDED;
    usbc.handle.Init.speed = PCD_SPEED_FULL;
    usbc.handle.Init.low_power_enable = 0;
    usbc.handle.Init.lpm_enable = 0;
    usbc.handle.Init.battery_charging_enable = 0;

    // Initialize LL Driver
    HAL_PCD_Init(&usbc.handle);

    HAL_PCDEx_PMAConfig(&usbc.handle, 0x00, PCD_SNG_BUF,
                        stm32_usbc_pma_alloc(0x40));
    HAL_PCDEx_PMAConfig(&usbc.handle, 0x80, PCD_SNG_BUF,
                        stm32_usbc_pma_alloc(0x40));

}

开发者ID:Gitsyshk，项目名称:lk，代码行数:25，代码来源:usbc.c

示例4: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef  USBD_LL_Init (USBD_HandleTypeDef *pdev)
{
  /* Init USB_IP */
  if (pdev->id == DEVICE_FS) {
  /* Link The driver to the stack */
  hpcd_USB_OTG_FS.pData = pdev;
  pdev->pData = &hpcd_USB_OTG_FS;

  hpcd_USB_OTG_FS.Instance = USB_OTG_FS;
  hpcd_USB_OTG_FS.Init.dev_endpoints = 4;
  hpcd_USB_OTG_FS.Init.speed = PCD_SPEED_FULL;
  hpcd_USB_OTG_FS.Init.dma_enable = DISABLE;
//  hpcd_USB_OTG_FS.Init.ep0_mps = DEP0CTL_MPS_64;
  hpcd_USB_OTG_FS.Init.ep0_mps = 0x40;
  hpcd_USB_OTG_FS.Init.phy_itface = PCD_PHY_EMBEDDED;
  hpcd_USB_OTG_FS.Init.Sof_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.low_power_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.lpm_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.vbus_sensing_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.use_dedicated_ep1 = DISABLE;
  if (HAL_PCD_Init(&hpcd_USB_OTG_FS) != HAL_OK)
  {
    Error_Handler();
  }

  HAL_PCDEx_SetRxFiFo(&hpcd_USB_OTG_FS, 0x80);
  HAL_PCDEx_SetTxFiFo(&hpcd_USB_OTG_FS, 0, 0x40);
  HAL_PCDEx_SetTxFiFo(&hpcd_USB_OTG_FS, 1, 0x80);
  }
  return USBD_OK;
}

开发者ID:fzi-forschungszentrum-informatik，项目名称:NIKI40，代码行数:36，代码来源:usbd_conf.c

示例5: USBD_LL_Init

USBD_StatusTypeDef USBD_LL_Init(USBD_HandleTypeDef *pdev)
{ 
	/* Init USB_IP */
	/* Link The driver to the stack */
	hpcd_USB_FS.pData = pdev;
	pdev->pData = &hpcd_USB_FS;

	hpcd_USB_FS.Instance = USB;
	hpcd_USB_FS.Init.dev_endpoints = 5;
	hpcd_USB_FS.Init.speed = PCD_SPEED_FULL;
	hpcd_USB_FS.Init.ep0_mps = DEP0CTL_MPS_64;
	hpcd_USB_FS.Init.phy_itface = PCD_PHY_EMBEDDED;
	hpcd_USB_FS.Init.low_power_enable = DISABLE;
	hpcd_USB_FS.Init.lpm_enable = DISABLE;
	HAL_PCD_Init(&hpcd_USB_FS);

	/*
	* PMA layout
	*  0x00 -  0x17 (24 bytes) metadata?
	*  0x18 -  0x57 (64 bytes) EP0 OUT
	*  0x58 -  0x97 (64 bytes) EP0 IN
	*  0x98 -  0xD7 (64 bytes) EP1 IN
	*  0xD8 - 0x157 (128 bytes) EP1 OUT (buffer 1)
	* 0x158 - 0x1D7 (128 bytes) EP1 OUT (buffer 2)
	*/
	HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x00 , PCD_SNG_BUF, 24);
	HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x80 , PCD_SNG_BUF, 0x58);
	HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x81 , PCD_SNG_BUF, 0x98);
	HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x02 , PCD_DBL_BUF, 0x00D80158);

	return USBD_OK;
}

开发者ID:HubertD，项目名称:candleLight_fw，代码行数:32，代码来源:usbd_conf.c

示例6: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_Init(USBD_HandleTypeDef *pdev)
{
     /* Change Systick prioity */
  NVIC_SetPriority (SysTick_IRQn, 0);

  /*Set LL Driver parameters */
  hpcd.Instance = USB_OTG_FS;               /*Register base address*/
  hpcd.Init.dev_endpoints = 4;              /*device endpoints number*/
  hpcd.Init.use_dedicated_ep1 = 0;          /*Enable or disable the use of the dedicated EP1 interrupt.*/
  hpcd.Init.ep0_mps = 0x40;                 /*Set the Endpoint 0 Max Packet size.(0x40=64)*/
  hpcd.Init.dma_enable = 0;                 /*Enable or disable of the USB embedded DMA*/
  hpcd.Init.low_power_enable = 0;           /*Enable or disable the low power mode*/
  hpcd.Init.phy_itface = PCD_PHY_EMBEDDED;  /*Select the used PHY interface*/
  hpcd.Init.Sof_enable = 0;                 /*Enable or disable the output of the SOF signal*/
  hpcd.Init.speed = PCD_SPEED_FULL;         /*USB Core speed*/
  hpcd.Init.vbus_sensing_enable = 1;        /*Enable or disable the VBUS Sensing feature*/
  /* Link The driver to the stack */
   hpcd.pData = pdev;
  pdev->pData = &hpcd;
  /*Initialize LL Driver */
  HAL_PCD_Init(&hpcd);

  HAL_PCDEx_SetRxFiFo(&hpcd, 0x80);         /*0x80=128*/
  HAL_PCDEx_SetTxFiFo(&hpcd, 0, 0x40);      /*0x40=64*/
  HAL_PCDEx_SetTxFiFo(&hpcd, 1, 0x80);      /*0x80=128*/

  return USBD_OK;
}

开发者ID:cooland，项目名称:oscockpit，代码行数:33，代码来源:usbd_conf.c

示例7: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef  USBD_LL_Init (USBD_HandleTypeDef *pdev)
{ 
  /* Init USB_IP */
  if (pdev->id == DEVICE_HS) {
  /* Link The driver to the stack */
  hpcd_USB_OTG_HS.pData = pdev;
  pdev->pData = &hpcd_USB_OTG_HS;

  hpcd_USB_OTG_HS.Instance = USB_OTG_HS;
  hpcd_USB_OTG_HS.Init.dev_endpoints = 11;
  hpcd_USB_OTG_HS.Init.speed = PCD_SPEED_FULL;
  hpcd_USB_OTG_HS.Init.dma_enable = DISABLE;
  hpcd_USB_OTG_HS.Init.ep0_mps = DEP0CTL_MPS_64;
  hpcd_USB_OTG_HS.Init.phy_itface = USB_OTG_EMBEDDED_PHY;
  hpcd_USB_OTG_HS.Init.Sof_enable = DISABLE;
  hpcd_USB_OTG_HS.Init.low_power_enable = DISABLE;
  hpcd_USB_OTG_HS.Init.lpm_enable = DISABLE;
  hpcd_USB_OTG_HS.Init.vbus_sensing_enable = DISABLE;
  hpcd_USB_OTG_HS.Init.use_dedicated_ep1 = DISABLE;
  hpcd_USB_OTG_HS.Init.use_external_vbus = DISABLE;
  HAL_PCD_Init(&hpcd_USB_OTG_HS);

  HAL_PCD_SetRxFiFo(&hpcd_USB_OTG_HS, 0x200);
  HAL_PCD_SetTxFiFo(&hpcd_USB_OTG_HS, 0, 0x80);
  HAL_PCD_SetTxFiFo(&hpcd_USB_OTG_HS, 1, 0x174);
  }
  return USBD_OK;
}

开发者ID:babelbi，项目名称:OpenLogicMaster，代码行数:33，代码来源:usbd_conf.c

示例8: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_Init(USBD_HandleTypeDef *pdev)
{
    /* Set LL Driver parameters */
    hpcd.Instance = USB_OTG_FS;
    hpcd.Init.dev_endpoints = 4;
    hpcd.Init.use_dedicated_ep1 = 0;
    hpcd.Init.ep0_mps = 0x40;
    hpcd.Init.dma_enable = 0;
    hpcd.Init.low_power_enable = 1;
    hpcd.Init.phy_itface = PCD_PHY_EMBEDDED;
    hpcd.Init.Sof_enable = 0;
    hpcd.Init.speed = PCD_SPEED_FULL;
    hpcd.Init.vbus_sensing_enable = 1;
    hpcd.Init.lpm_enable = 0;

    /* Link The driver to the stack */
    hpcd.pData = pdev;
    pdev->pData = &hpcd;

    /* Initialize LL Driver */
    HAL_PCD_Init(&hpcd);

    HAL_PCDEx_SetRxFiFo(&hpcd, 0x80);
    HAL_PCDEx_SetTxFiFo(&hpcd, 0, 0x40);
    HAL_PCDEx_SetTxFiFo(&hpcd, 1, 0x80);

    return USBD_OK;
}

开发者ID:JUMA-IO，项目名称:STM32_Platform，代码行数:33，代码来源:usbd_conf.c

示例9: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef  USBD_LL_Init( USBD_HandleTypeDef *pdev )
{
  hpcd.pData                  = pdev;
  pdev->pData                 = &hpcd;

  hpcd.Instance               = USB_OTG_FS;
  hpcd.Init.dev_endpoints     = 4;
  hpcd.Init.speed             = PCD_SPEED_FULL;
  hpcd.Init.dma_enable        = DISABLE;
  hpcd.Init.ep0_mps           = DEP0CTL_MPS_64; // 0x40; ?
  hpcd.Init.phy_itface        = PCD_PHY_EMBEDDED;
  hpcd.Init.Sof_enable        = DISABLE;
  hpcd.Init.low_power_enable  = DISABLE;
  hpcd.Init.lpm_enable        = DISABLE;
  hpcd.Init.use_dedicated_ep1 = DISABLE;

  #ifdef BOARD_USB_DEFAULT_VBUS_PIN
  hpcd.Init.vbus_sensing_enable = ENABLE;
  #else
  hpcd.Init.vbus_sensing_enable = DISABLE;
  #endif

  if( HAL_PCD_Init( &hpcd ) != HAL_OK ) {
    errno = 50000;
    return USBD_FAIL;
  };

  HAL_PCDEx_SetRxFiFo( &hpcd, 0x80 );
  HAL_PCDEx_SetTxFiFo( &hpcd, 0, 0x40 );
  HAL_PCDEx_SetTxFiFo( &hpcd, 1, 0x80 );

  return USBD_OK;
}

开发者ID:atu-guda，项目名称:stm32oxc，代码行数:38，代码来源:usbd_conf.cpp

示例10: USBD_LL_Init

/**
 * Initializes the Low Level portion of the Device driver.
 * 
 * @param  pdev: Device handle
 * @return USBD Status
 */
USBD_StatusTypeDef USBD_LL_Init(USBD_HandleTypeDef *pdev) {
    if(pdev->id == DEVICE_FS) {
        // Set LL Driver parameters
        hpcd_FS.Instance = USB_OTG_FS;
        hpcd_FS.Init.speed = PCD_SPEED_FULL;
        hpcd_FS.Init.dev_endpoints = 4;
        hpcd_FS.Init.use_dedicated_ep1 = 0;
        hpcd_FS.Init.ep0_mps = 0x40;
        hpcd_FS.Init.dma_enable = DISABLE;
        hpcd_FS.Init.low_power_enable = ENABLE;
        hpcd_FS.Init.phy_itface = PCD_PHY_EMBEDDED;
        hpcd_FS.Init.Sof_enable = DISABLE;
        hpcd_FS.Init.vbus_sensing_enable = ENABLE;
        hpcd_FS.Init.use_external_vbus = ENABLE;
        
        // Link the driver to the stack
        hpcd_FS.pData = pdev;
        pdev->pData = &hpcd_FS;
        
        // Initialize LL Driver
        HAL_PCD_Init(&hpcd_FS);
        HAL_PCD_SetRxFiFo(&hpcd_FS, 0x80);
        HAL_PCD_SetTxFiFo(&hpcd_FS, 0, 0x40);
        HAL_PCD_SetTxFiFo(&hpcd_FS, 1, 0x80);
    }
    return USBD_OK;
}

开发者ID:glocklueng，项目名称:impy，代码行数:33，代码来源:usbd_conf.c

示例11: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef  USBD_LL_Init (USBD_HandleTypeDef *pdev)
{ 
  /* Init USB_IP */
  /* Link The driver to the stack */
  hpcd_USB_FS.pData = pdev;
  pdev->pData = &hpcd_USB_FS;

  hpcd_USB_FS.Instance = USB;
  hpcd_USB_FS.Init.dev_endpoints = 8;
  hpcd_USB_FS.Init.speed = PCD_SPEED_FULL;
  hpcd_USB_FS.Init.ep0_mps = DEP0CTL_MPS_8;
  hpcd_USB_FS.Init.low_power_enable = DISABLE;
  hpcd_USB_FS.Init.lpm_enable = DISABLE;
  hpcd_USB_FS.Init.battery_charging_enable = DISABLE;
  if (HAL_PCD_Init(&hpcd_USB_FS) != HAL_OK)
  {
    Error_Handler();
  }

  HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x00 , PCD_SNG_BUF, 0x18);
  HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x80 , PCD_SNG_BUF, 0x58);
  HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x81 , PCD_SNG_BUF, 0xC0);  
  HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x01 , PCD_SNG_BUF, 0x110);
  HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x82 , PCD_SNG_BUF, 0x100);  
  return USBD_OK;
}

开发者ID:loboris，项目名称:mini-sys，代码行数:31，代码来源:usbd_conf.c

示例12: MX_USB_PCD_Init

/* USB init function */
static void MX_USB_PCD_Init(void)
{

  hpcd_USB_FS.Instance = USB;
  hpcd_USB_FS.Init.dev_endpoints = 8;
  hpcd_USB_FS.Init.speed = PCD_SPEED_FULL;
  hpcd_USB_FS.Init.ep0_mps = DEP0CTL_MPS_8;
  hpcd_USB_FS.Init.low_power_enable = DISABLE;
  hpcd_USB_FS.Init.lpm_enable = DISABLE;
  hpcd_USB_FS.Init.battery_charging_enable = DISABLE;
  if (HAL_PCD_Init(&hpcd_USB_FS) != HAL_OK)
  {
    Error_Handler();
  }

}

开发者ID:PaxInstruments，项目名称:PaxInstruments-LabWiz-firmware，代码行数:17，代码来源:labwiz_entry.c

示例13: MX_USB_PCD_Init

void MX_USB_PCD_Init(void)
{

  hpcd_USB_FS.Instance = USB;
  hpcd_USB_FS.Init.dev_endpoints = 8;
  hpcd_USB_FS.Init.speed = PCD_SPEED_FULL;
  hpcd_USB_FS.Init.ep0_mps = DEP0CTL_MPS_8;
  hpcd_USB_FS.Init.phy_itface = PCD_PHY_EMBEDDED;
  hpcd_USB_FS.Init.low_power_enable = DISABLE;
  hpcd_USB_FS.Init.lpm_enable = DISABLE;
  if (HAL_PCD_Init(&hpcd_USB_FS) != HAL_OK)
  {
    Error_Handler();
  }

}

开发者ID:jbeck3，项目名称:QUADROTOR_CONTROLLER_STM32F070，代码行数:16，代码来源:usb.c

示例14: MX_USB_OTG_FS_PCD_Init

void MX_USB_OTG_FS_PCD_Init(void)
{

  hpcd_USB_OTG_FS.Instance = USB_OTG_FS;
  hpcd_USB_OTG_FS.Init.dev_endpoints = 7;
  hpcd_USB_OTG_FS.Init.speed = PCD_SPEED_FULL;
  hpcd_USB_OTG_FS.Init.dma_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.ep0_mps = DEP0CTL_MPS_64;
  hpcd_USB_OTG_FS.Init.phy_itface = PCD_PHY_EMBEDDED;
  hpcd_USB_OTG_FS.Init.Sof_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.low_power_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.lpm_enable = DISABLE;
  hpcd_USB_OTG_FS.Init.vbus_sensing_enable = ENABLE;
  hpcd_USB_OTG_FS.Init.use_dedicated_ep1 = DISABLE;
  HAL_PCD_Init(&hpcd_USB_OTG_FS);

}

开发者ID:bitschieber，项目名称:ISFCarUc，代码行数:17，代码来源:usb_otg.c

示例15: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_Init(USBD_HandleTypeDef *pdev)
{    
  /* Set LL Driver parameters */
  hpcd.Instance = USB;
  hpcd.Init.dev_endpoints = 8;
  hpcd.Init.ep0_mps = 0x40;
  hpcd.Init.phy_itface = PCD_PHY_EMBEDDED;
  hpcd.Init.speed = PCD_SPEED_FULL;
  /* Link The driver to the stack */
  hpcd.pData = pdev;
  pdev->pData = &hpcd;
  /* Initialize LL Driver */
  HAL_PCD_Init(&hpcd);
  
  HAL_PCDEx_PMAConfig(&hpcd , 0x00 , PCD_SNG_BUF, 0x18);
  HAL_PCDEx_PMAConfig(&hpcd , 0x80 , PCD_SNG_BUF, 0x58); 

  return USBD_OK;
}

开发者ID:jmoyerman，项目名称:stm32f0_cube，代码行数:24，代码来源:usbd_conf.c

示例16: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef  USBD_LL_Init (USBD_HandleTypeDef *pdev)
{ 
  /* Init USB_IP */
  /* Link The driver to the stack */
  hpcd_USB_FS.pData = pdev;
  pdev->pData = &hpcd_USB_FS;

  hpcd_USB_FS.Instance = USB;
  hpcd_USB_FS.Init.dev_endpoints = 5;
  hpcd_USB_FS.Init.speed = PCD_SPEED_FULL;
  hpcd_USB_FS.Init.ep0_mps = DEP0CTL_MPS_8;
  hpcd_USB_FS.Init.phy_itface = PCD_PHY_EMBEDDED;
  hpcd_USB_FS.Init.low_power_enable = DISABLE;
  hpcd_USB_FS.Init.battery_charging_enable = DISABLE;
  HAL_PCD_Init(&hpcd_USB_FS);

  HAL_PCDEx_PMAConfig(pdev->pData , 0x00 , PCD_SNG_BUF, 0x18);
  HAL_PCDEx_PMAConfig(pdev->pData , 0x80 , PCD_SNG_BUF, 0x58);
  HAL_PCDEx_PMAConfig(pdev->pData , 0x81 , PCD_SNG_BUF, 0x100);  
  return USBD_OK;
}

开发者ID:chathuranga1931，项目名称:Unit-Test-Development，代码行数:26，代码来源:usbd_conf.c

示例17: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_Init(USBD_HandleTypeDef *pdev)
{    
  /* Set LL Driver parameters */
  hpcd.Instance = USB;
  hpcd.Init.dev_endpoints = 8;
  hpcd.Init.ep0_mps = PCD_EP0MPS_64;
  hpcd.Init.phy_itface = PCD_PHY_EMBEDDED;
  hpcd.Init.speed = PCD_SPEED_FULL;
  /* Link The driver to the stack */
  hpcd.pData = pdev;
  pdev->pData = &hpcd;
  /* Initialize LL Driver */
  HAL_PCD_Init(pdev->pData);
  
  HAL_PCDEx_PMAConfig(pdev->pData , 0x00 , PCD_SNG_BUF, 0x40);
  HAL_PCDEx_PMAConfig(pdev->pData , 0x80 , PCD_SNG_BUF, 0x80);
  HAL_PCDEx_PMAConfig(pdev->pData , CDC_IN_EP , PCD_SNG_BUF, 0xC0);  
  HAL_PCDEx_PMAConfig(pdev->pData , CDC_OUT_EP , PCD_SNG_BUF, 0x110);
  HAL_PCDEx_PMAConfig(pdev->pData , CDC_CMD_EP , PCD_SNG_BUF, 0x100); 
    
  return USBD_OK;
}

开发者ID:eleciawhite，项目名称:STM32Cube，代码行数:27，代码来源:usbd_conf.c

示例18: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef USBD_LL_Init(USBD_HandleTypeDef *pdev)
{
  /* Set LL Driver parameters */
  hpcd.Instance = USB;
  hpcd.Init.dev_endpoints = 8;
  hpcd.Init.ep0_mps = PCD_EP0MPS_64;
  hpcd.Init.phy_itface = PCD_PHY_EMBEDDED;
  hpcd.Init.speed = PCD_SPEED_FULL;
  hpcd.Init.low_power_enable = 0;

  /* Link The driver to the stack */
  hpcd.pData = pdev;
  pdev->pData = &hpcd;

  /* Initialize LL Driver */
  HAL_PCD_Init((PCD_HandleTypeDef*)pdev->pData);

  HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x80 , PCD_SNG_BUF, 0x10);
  HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x00 , PCD_SNG_BUF, 0x50);
  HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x81 , PCD_SNG_BUF, 0x90);
  HAL_PCDEx_PMAConfig((PCD_HandleTypeDef*)pdev->pData , 0x01 , PCD_SNG_BUF, 0xD0);

  return USBD_OK;
}

开发者ID:apeng2012，项目名称:mi_ma_bao，代码行数:29，代码来源:usbd_conf.c

示例19: USBD_LL_Init

/**
  * @brief  Initializes the Low Level portion of the Device driver.  
  * @param  pdev: Device handle
  * @retval USBD Status
  */
USBD_StatusTypeDef  USBD_LL_Init (USBD_HandleTypeDef *pdev)
{ 
#if defined(USE_USB_FS)
if (pdev->id ==  USB_PHY_FS_ID)
{
  /*Set LL Driver parameters */
  pcd_fs_handle.Instance = USB_OTG_FS;
  pcd_fs_handle.Init.dev_endpoints = 4;
  pcd_fs_handle.Init.use_dedicated_ep1 = 0;
  pcd_fs_handle.Init.ep0_mps = 0x40;
  pcd_fs_handle.Init.dma_enable = 0;
  pcd_fs_handle.Init.low_power_enable = 0;
  pcd_fs_handle.Init.phy_itface = PCD_PHY_EMBEDDED;
  pcd_fs_handle.Init.Sof_enable = 1;
  pcd_fs_handle.Init.speed = PCD_SPEED_FULL;
#if defined(MCU_SERIES_L4)
  pcd_fs_handle.Init.lpm_enable = DISABLE;
  pcd_fs_handle.Init.battery_charging_enable = DISABLE;
#endif
#if !defined(MICROPY_HW_USB_VBUS_DETECT_PIN)
  pcd_fs_handle.Init.vbus_sensing_enable = 0; // No VBUS Sensing on USB0
#else
  pcd_fs_handle.Init.vbus_sensing_enable = 1;
#endif
  /* Link The driver to the stack */
  pcd_fs_handle.pData = pdev;
  pdev->pData = &pcd_fs_handle;
  /*Initialize LL Driver */
  HAL_PCD_Init(&pcd_fs_handle);

  HAL_PCD_SetRxFiFo(&pcd_fs_handle, 0x80);
  HAL_PCD_SetTxFiFo(&pcd_fs_handle, 0, 0x20);
  HAL_PCD_SetTxFiFo(&pcd_fs_handle, 1, 0x40);
  HAL_PCD_SetTxFiFo(&pcd_fs_handle, 2, 0x20);
  HAL_PCD_SetTxFiFo(&pcd_fs_handle, 3, 0x40);
}
#endif
#if defined(USE_USB_HS)
if (pdev->id == USB_PHY_HS_ID)
{
#if defined(USE_USB_HS_IN_FS)
  /*Set LL Driver parameters */
  pcd_hs_handle.Instance = USB_OTG_HS;
  pcd_hs_handle.Init.dev_endpoints = 4;
  pcd_hs_handle.Init.use_dedicated_ep1 = 0;
  pcd_hs_handle.Init.ep0_mps = 0x40;
  pcd_hs_handle.Init.dma_enable = 0;
  pcd_hs_handle.Init.low_power_enable = 0;
  pcd_hs_handle.Init.phy_itface = PCD_PHY_EMBEDDED;
  pcd_hs_handle.Init.Sof_enable = 1;
  pcd_hs_handle.Init.speed = PCD_SPEED_HIGH_IN_FULL;
#if !defined(MICROPY_HW_USB_VBUS_DETECT_PIN)
  pcd_hs_handle.Init.vbus_sensing_enable = 0; // No VBUS Sensing on USB0
#else
  pcd_hs_handle.Init.vbus_sensing_enable = 1;
#endif
  /* Link The driver to the stack */
  pcd_hs_handle.pData = pdev;
  pdev->pData = &pcd_hs_handle;
  /*Initialize LL Driver */
  HAL_PCD_Init(&pcd_hs_handle);

  HAL_PCD_SetRxFiFo(&pcd_hs_handle, 0x80);
  HAL_PCD_SetTxFiFo(&pcd_hs_handle, 0, 0x20);
  HAL_PCD_SetTxFiFo(&pcd_hs_handle, 1, 0x40);
  HAL_PCD_SetTxFiFo(&pcd_hs_handle, 2, 0x20);
  HAL_PCD_SetTxFiFo(&pcd_hs_handle, 3, 0x40);
#else // !defined(USE_USB_HS_IN_FS)
  /*Set LL Driver parameters */
  pcd_hs_handle.Instance = USB_OTG_HS;
  pcd_hs_handle.Init.dev_endpoints = 6;
  pcd_hs_handle.Init.use_dedicated_ep1 = 0;
  pcd_hs_handle.Init.ep0_mps = 0x40;
  
  /* Be aware that enabling USB-DMA mode will result in data being sent only by
     multiple of 4 packet sizes. This is due to the fact that USB-DMA does
     not allow sending data from non word-aligned addresses.
     For this specific application, it is advised to not enable this option
     unless required. */
  pcd_hs_handle.Init.dma_enable = 0;
  
  pcd_hs_handle.Init.low_power_enable = 0;
  pcd_hs_handle.Init.phy_itface = PCD_PHY_ULPI;
  pcd_hs_handle.Init.Sof_enable = 1;
  pcd_hs_handle.Init.speed = PCD_SPEED_HIGH;
  pcd_hs_handle.Init.vbus_sensing_enable = 1;
  /* Link The driver to the stack */
  pcd_hs_handle.pData = pdev;
  pdev->pData = &pcd_hs_handle;
  /*Initialize LL Driver */
  HAL_PCD_Init(&pcd_hs_handle);
  
  HAL_PCD_SetRxFiFo(&pcd_hs_handle, 0x200);
  HAL_PCD_SetTxFiFo(&pcd_hs_handle, 0, 0x80);
  HAL_PCD_SetTxFiFo(&pcd_hs_handle, 1, 0x174);
//.........这里部分代码省略.........

开发者ID:AriZuu，项目名称:micropython，代码行数:101，代码来源:usbd_conf.c

示例20: usb_dc_stm32_init

static int usb_dc_stm32_init(void)
{
	HAL_StatusTypeDef status;
	unsigned int i;

#ifdef USB
	usb_dc_stm32_state.pcd.Instance = USB;
	usb_dc_stm32_state.pcd.Init.speed = PCD_SPEED_FULL;
	usb_dc_stm32_state.pcd.Init.dev_endpoints = DT_USB_NUM_BIDIR_ENDPOINTS;
	usb_dc_stm32_state.pcd.Init.phy_itface = PCD_PHY_EMBEDDED;
	usb_dc_stm32_state.pcd.Init.ep0_mps = PCD_EP0MPS_64;
	usb_dc_stm32_state.pcd.Init.low_power_enable = 0;
#else /* USB_OTG_FS || USB_OTG_HS */
#ifdef DT_USB_HS_BASE_ADDRESS
	usb_dc_stm32_state.pcd.Instance = USB_OTG_HS;
#else
	usb_dc_stm32_state.pcd.Instance = USB_OTG_FS;
#endif
	usb_dc_stm32_state.pcd.Init.dev_endpoints = DT_USB_NUM_BIDIR_ENDPOINTS;
	usb_dc_stm32_state.pcd.Init.speed = usb_dc_stm32_get_maximum_speed();
#if defined(DT_COMPAT_ST_STM32_USBPHYC) && defined(DT_USB_HS_BASE_ADDRESS)
	usb_dc_stm32_state.pcd.Init.phy_itface = USB_OTG_HS_EMBEDDED_PHY;
#else
	usb_dc_stm32_state.pcd.Init.phy_itface = PCD_PHY_EMBEDDED;
#endif /* DT_COMPAT_ST_STM32_USBPHYC */
	usb_dc_stm32_state.pcd.Init.ep0_mps = USB_OTG_MAX_EP0_SIZE;
	usb_dc_stm32_state.pcd.Init.vbus_sensing_enable = DISABLE;

#ifndef CONFIG_SOC_SERIES_STM32F1X
	usb_dc_stm32_state.pcd.Init.dma_enable = DISABLE;
#endif

#endif /* USB */

#ifdef CONFIG_USB_DEVICE_SOF
	usb_dc_stm32_state.pcd.Init.Sof_enable = 1;
#endif /* CONFIG_USB_DEVICE_SOF */

	LOG_DBG("HAL_PCD_Init");
	status = HAL_PCD_Init(&usb_dc_stm32_state.pcd);
	if (status != HAL_OK) {
		LOG_ERR("PCD_Init failed, %d", (int)status);
		return -EIO;
	}

	LOG_DBG("HAL_PCD_Start");
	status = HAL_PCD_Start(&usb_dc_stm32_state.pcd);
	if (status != HAL_OK) {
		LOG_ERR("PCD_Start failed, %d", (int)status);
		return -EIO;
	}

	usb_dc_stm32_state.out_ep_state[EP0_IDX].ep_mps = EP0_MPS;
	usb_dc_stm32_state.out_ep_state[EP0_IDX].ep_type = EP_TYPE_CTRL;
	usb_dc_stm32_state.in_ep_state[EP0_IDX].ep_mps = EP0_MPS;
	usb_dc_stm32_state.in_ep_state[EP0_IDX].ep_type = EP_TYPE_CTRL;

#ifdef USB
	/* Start PMA configuration for the endpoints after the BTABLE. */
	usb_dc_stm32_state.pma_offset = USB_BTABLE_SIZE;

	for (i = 0U; i < DT_USB_NUM_BIDIR_ENDPOINTS; i++) {
		k_sem_init(&usb_dc_stm32_state.in_ep_state[i].write_sem, 1, 1);
	}
#else /* USB_OTG_FS */
	/* TODO: make this dynamic (depending usage) */
	HAL_PCDEx_SetRxFiFo(&usb_dc_stm32_state.pcd, FIFO_EP_WORDS);
	for (i = 0U; i < DT_USB_NUM_BIDIR_ENDPOINTS; i++) {
		HAL_PCDEx_SetTxFiFo(&usb_dc_stm32_state.pcd, i,
				    FIFO_EP_WORDS);
		k_sem_init(&usb_dc_stm32_state.in_ep_state[i].write_sem, 1, 1);
	}
#endif /* USB */

	IRQ_CONNECT(DT_USB_IRQ, DT_USB_IRQ_PRI,
		    usb_dc_stm32_isr, 0, 0);
	irq_enable(DT_USB_IRQ);
	return 0;
}

开发者ID:loicpoulain，项目名称:zephyr，代码行数:79，代码来源:usb_dc_stm32.c

注：本文中的HAL_PCD_Init函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ HAL_PCD_SetAddress函数代码示例发布时间：2022-05-30

C++ HAL_PCD_IRQHandler函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：18268|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9677|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8177|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8548|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8457|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9388|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8427|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7862|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8411|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7394|2022-11-06

客服电话

电子邮件

C++ HAL_PCD_Init函数代码示例

示例1: USBD_LL_Init

示例2: USBD_LL_Init

示例3: stm32_usbc_init

示例4: USBD_LL_Init

示例5: USBD_LL_Init

示例6: USBD_LL_Init

示例7: USBD_LL_Init

示例8: USBD_LL_Init

示例9: USBD_LL_Init

示例10: USBD_LL_Init

示例11: USBD_LL_Init

示例12: MX_USB_PCD_Init

示例13: MX_USB_PCD_Init

示例14: MX_USB_OTG_FS_PCD_Init

示例15: USBD_LL_Init

示例16: USBD_LL_Init

示例17: USBD_LL_Init

示例18: USBD_LL_Init

示例19: USBD_LL_Init

示例20: usb_dc_stm32_init

请发表评论

全部评论

上一篇：

下一篇：

bradtraversy/iweather: Ionic 3 mobile we

joaomh/curso-de-matlab

断牙刷新位置时间（断牙属性及刷新位置介绍

CVE-2022-34114

rugk/mastodon-simplified-federation: Sim

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053