C++ IS_PWR_PVD_LEVEL函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中IS_PWR_PVD_LEVEL函数的典型用法代码示例。如果您正苦于以下问题：C++ IS_PWR_PVD_LEVEL函数的具体用法？C++ IS_PWR_PVD_LEVEL怎么用？C++ IS_PWR_PVD_LEVEL使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了IS_PWR_PVD_LEVEL函数的9个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: HAL_PWR_PVDConfig

/**
  * @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD).
  * @param sConfigPVD: pointer to an PWR_PVDTypeDef structure that contains the configuration
  *        information for the PVD.
  * @note Refer to the electrical characteristics of your device datasheet for
  *         more details about the voltage threshold corresponding to each
  *         detection level.
  * @retval None
  */
void HAL_PWR_PVDConfig(PWR_PVDTypeDef * sConfigPVD)
{
	/* Check the parameters */
	assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel));
	assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode));

	/* Set PLS[7:5] bits according to PVDLevel value */
	MODIFY_REG(PWR->CR, PWR_CR_PLS, sConfigPVD->PVDLevel);

	/* Clear any previous config. Keep it clear if no event or IT mode is selected */
	__HAL_PWR_PVD_EXTI_DISABLE_EVENT();
	__HAL_PWR_PVD_EXTI_DISABLE_IT();
	__HAL_PWR_PVD_EXTI_CLEAR_EGDE_TRIGGER();

	/* Configure interrupt mode */
	if ((sConfigPVD->Mode & PVD_MODE_IT) == PVD_MODE_IT) {
		__HAL_PWR_PVD_EXTI_ENABLE_IT();
	}

	/* Configure event mode */
	if ((sConfigPVD->Mode & PVD_MODE_EVT) == PVD_MODE_EVT) {
		__HAL_PWR_PVD_EXTI_ENABLE_EVENT();
	}

	/* Configure the edge */
	if ((sConfigPVD->Mode & PVD_RISING_EDGE) == PVD_RISING_EDGE) {
		__HAL_PWR_PVD_EXTI_SET_RISING_EDGE_TRIGGER();
	}

	if ((sConfigPVD->Mode & PVD_FALLING_EDGE) == PVD_FALLING_EDGE) {
		__HAL_PWR_PVD_EXTI_SET_FALLING_EGDE_TRIGGER();
	}
}

开发者ID:nvdl，项目名称:pymite，代码行数:42，代码来源:stm32f0xx_hal_pwr_ex.c

示例2: HAL_PWR_PVDConfig

/**
  * @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD).
  * @param sConfigPVD: pointer to an PWR_PVDTypeDef structure that contains the configuration
  *        information for the PVD.
  * @note Refer to the electrical characteristics of your device datasheet for
  *         more details about the voltage threshold corresponding to each
  *         detection level.
  * @retval None
  */
void HAL_PWR_PVDConfig(PWR_PVDTypeDef *sConfigPVD)
{
  /* Check the parameters */
  assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel));
  assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode));

  /* Set PLS[7:5] bits according to PVDLevel value */
  MODIFY_REG(PWR->CR, PWR_CR_PLS, sConfigPVD->PVDLevel);

  /* Configure the EXTI 16 interrupt */
  if((sConfigPVD->Mode == PWR_MODE_IT_RISING_FALLING) ||\
     (sConfigPVD->Mode == PWR_MODE_IT_FALLING) ||\
     (sConfigPVD->Mode == PWR_MODE_IT_RISING))
  {
    __HAL_PVD_EXTI_ENABLE_IT(PWR_EXTI_LINE_PVD);
  }
  /* Configure the rising edge */
  if((sConfigPVD->Mode == PWR_MODE_IT_RISING_FALLING) ||\
     (sConfigPVD->Mode == PWR_MODE_IT_RISING))
  {
    EXTI->RTSR |= PWR_EXTI_LINE_PVD;
  }
  /* Configure the falling edge */
  if((sConfigPVD->Mode == PWR_MODE_IT_RISING_FALLING) ||\
     (sConfigPVD->Mode == PWR_MODE_IT_FALLING))
  {
    EXTI->FTSR |= PWR_EXTI_LINE_PVD;
  }
}

开发者ID:23chrischen，项目名称:mbed，代码行数:38，代码来源:stm32f3xx_hal_pwr_ex.c

示例3: PWR_PVDLevelConfig

/**
  * @brief  Configures the voltage threshold detected by the Power Voltage Detector(PVD).
  * @param  PWR_PVDLevel: specifies the PVD detection level
  *   This parameter can be one of the following values:
  *     @arg PWR_PVDLevel_2V2: PVD detection level set to 2.2V
  *     @arg PWR_PVDLevel_2V3: PVD detection level set to 2.3V
  *     @arg PWR_PVDLevel_2V4: PVD detection level set to 2.4V
  *     @arg PWR_PVDLevel_2V5: PVD detection level set to 2.5V
  *     @arg PWR_PVDLevel_2V6: PVD detection level set to 2.6V
  *     @arg PWR_PVDLevel_2V7: PVD detection level set to 2.7V
  *     @arg PWR_PVDLevel_2V8: PVD detection level set to 2.8V
  *     @arg PWR_PVDLevel_2V9: PVD detection level set to 2.9V
  * @retval None
  */
void PWR_PVDLevelConfig(uint32_t PWR_PVDLevel)
{
	
#ifdef	OS_UCOS
	OS_CPU_SR  cpu_sr;
#endif
	

  uint32_t tmpreg = 0;
	
#ifdef	OS_UCOS
	OS_ENTER_CRITICAL();
#endif
	 
  /* Check the parameters */
  assert_param(IS_PWR_PVD_LEVEL(PWR_PVDLevel));
  tmpreg = PWR->CR;
  /* Clear PLS[7:5] bits */
  tmpreg &= CR_PLS_MASK;
  /* Set PLS[7:5] bits according to PWR_PVDLevel value */
  tmpreg |= PWR_PVDLevel;
  /* Store the new value */
  PWR->CR = tmpreg;
	
#ifdef	OS_UCOS
	OS_EXIT_CRITICAL();
#endif
	
}

开发者ID:joyceandpig，项目名称:STM32_USB_MASS，代码行数:43，代码来源:stm32f10x_pwr.c

示例4: PWR_PVDLevelConfig

/**
  * @brief  Configures the voltage threshold detected by the Power Voltage Detector(PVD).
  * @param  PWR_PVDLevel: specifies the PVD detection level
  *          This parameter can be one of the following values:
  *            @arg PWR_PVDLevel_1V85: PVD detection level set to 1.85V
  *            @arg PWR_PVDLevel_2V05: PVD detection level set to 2.05V
  *            @arg PWR_PVDLevel_2V26: PVD detection level set to 2.26V
  *            @arg PWR_PVDLevel_2V45: PVD detection level set to 2.45V
  *            @arg PWR_PVDLevel_2V65: PVD detection level set to 2.65V
  *            @arg PWR_PVDLevel_2V85: PVD detection level set to 2.85V
  *            @arg PWR_PVDLevel_3V05: PVD detection level set to 3.05V
  *            @arg PWR_PVDLevel_PVDIn: External input analog voltage (Compare internally to VREFINT)
  * @retval None
  */
void PWR_PVDLevelConfig(PWR_PVDLevel_TypeDef PWR_PVDLevel)
{
  /* Check the parameters */
  assert_param(IS_PWR_PVD_LEVEL(PWR_PVDLevel));

  /* Clear the PVD level */
  PWR->CSR1 &= (uint8_t)(~PWR_CSR1_PLS);

  /* Configure the PVD level */
  PWR->CSR1 |= PWR_PVDLevel;

}

开发者ID:ChangXiaodong，项目名称:manhole，代码行数:26，代码来源:stm8l15x_pwr.c

示例5: PWR_PVDLevelConfig

/**
  * @brief  Configures the voltage threshold detected by the Power Voltage
  *   Detector(PVD).
  * @param PWR_PVDLevel: specifies the PVD detection level
  *   This parameter can be one of the following values:
  * @arg PWR_PVDLevel_2V2: PVD detection level set to 2.2V
  * @arg PWR_PVDLevel_2V3: PVD detection level set to 2.3V
  * @arg PWR_PVDLevel_2V4: PVD detection level set to 2.4V
  * @arg PWR_PVDLevel_2V5: PVD detection level set to 2.5V
  * @arg PWR_PVDLevel_2V6: PVD detection level set to 2.6V
  * @arg PWR_PVDLevel_2V7: PVD detection level set to 2.7V
  * @arg PWR_PVDLevel_2V8: PVD detection level set to 2.8V
  * @arg PWR_PVDLevel_2V9: PVD detection level set to 2.9V
  * @retval : None
  */
void PWR_PVDLevelConfig(uint32_t PWR_PVDLevel) {
	uint32_t tmpreg = 0;
	/* Check the parameters */
	assert_param(IS_PWR_PVD_LEVEL(PWR_PVDLevel));
	tmpreg = PWR->CR;
	/* Clear PLS[7:5] bits */
	tmpreg &= CR_PLS_Mask;
	/* Set PLS[7:5] bits according to PWR_PVDLevel value */
	tmpreg |= PWR_PVDLevel;
	/* Store the new value */
	PWR->CR = tmpreg;
}

开发者ID:dunhaiyang，项目名称:dw1000_firmware，代码行数:27，代码来源:stm32f10x_pwr.c

示例6: PWR_PVDLevelConfig

/*******************************************************************************
* 函数名称: PWR_PVDLevelConfig
* 功能描述: 配置由电源电压探测器探测的电压门限值（PVD）.
* 输入参数: PWR_PVDLevel:PVD探测电平。
*                    这个参数可以取下面的值之一:
*                       - PWR_PVDLevel_2V2: PVD探测电平设置为 2.2V
*                       - PWR_PVDLevel_2V3: PVD探测电平设置为 2.3V
*                       - PWR_PVDLevel_2V4: PVD探测电平设置为 2.4V
*                       - PWR_PVDLevel_2V5: PVD探测电平设置为 2.5V
*                       - PWR_PVDLevel_2V6: PVD探测电平设置为 2.6V
*                       - PWR_PVDLevel_2V7: PVD探测电平设置为 2.7V
*                       - PWR_PVDLevel_2V8: PVD探测电平设置为 2.8V
*                       - PWR_PVDLevel_2V9: PVD探测电平设置为 2.9V
* 输出参数: 无
* 返回参数: 无
*******************************************************************************/
void PWR_PVDLevelConfig(u32 PWR_PVDLevel)
{
  u32 tmpreg = 0;

  /* Check the parameters [检查参数]*/
  assert_param(IS_PWR_PVD_LEVEL(PWR_PVDLevel));

  tmpreg = PWR->CR;

  /* Clear PLS[7:5] bits [清零PLS[7:5]位]*/
  tmpreg &= CR_PLS_Mask;

  /* Set PLS[7:5] bits according to PWR_PVDLevel value [依照PWR_PVDLevel的值置位PLS[7:5]]*/
  tmpreg |= PWR_PVDLevel;

  /* Store the new value [保存新的值]*/
  PWR->CR = tmpreg;
}

开发者ID:WrongChao，项目名称:lammbo-fly，代码行数:34，代码来源:stm32f10x_pwr.c

示例7: HAL_PWR_PVDConfig

/**
  * @brief Configures the voltage threshold detected by the Power Voltage Detector(PVD).
  * @param sConfigPVD: pointer to an PWR_PVDTypeDef structure that contains the configuration
  *        information for the PVD.
  * @note Refer to the electrical characteristics of your device datasheet for
  *         more details about the voltage threshold corresponding to each
  *         detection level.
  * @retval None
  */
void HAL_PWR_PVDConfig(PWR_PVDTypeDef *sConfigPVD)
{
 uint32_t tmpreg = 0;

  /* Check the parameters */
  assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel));

  tmpreg = PWR->CR;

  /* Clear PLS[7:5] bits */
  tmpreg &= ~ (uint32_t)PWR_CR_PLS;

  /* Set PLS[7:5] bits according to PVDLevel value */
  tmpreg |= sConfigPVD->PVDLevel;

  /* Store the new value */
  PWR->CR = tmpreg;

  /* Configure the EXTI 16 interrupt */
  if((sConfigPVD->Mode == PWR_MODE_IT_RISING_FALLING) ||\
     (sConfigPVD->Mode == PWR_MODE_IT_FALLING) ||\
     (sConfigPVD->Mode == PWR_MODE_IT_RISING)) 
  {
    __HAL_PVD_EXTI_ENABLE_IT(PWR_EXTI_LINE_PVD);
  }
  
  /* Clear the edge trigger  for the EXTI Line 16 (PVD) */
  EXTI->RTSR &= ~EXTI_RTSR_TR16;
  EXTI->FTSR &= ~EXTI_FTSR_TR16;

  /* Configure the rising edge */
  if((sConfigPVD->Mode == PWR_MODE_IT_RISING_FALLING) ||\
     (sConfigPVD->Mode == PWR_MODE_IT_RISING))
  {
    EXTI->RTSR |= PWR_EXTI_LINE_PVD;
  }
  /* Configure the falling edge */
  if((sConfigPVD->Mode == PWR_MODE_IT_RISING_FALLING) ||\
     (sConfigPVD->Mode == PWR_MODE_IT_FALLING))
  {
    EXTI->FTSR |= PWR_EXTI_LINE_PVD;
  }
}

开发者ID:hammerfet，项目名称:HotBit，代码行数:52，代码来源:stm32l0xx_hal_pwr.c

示例8: HAL_PWR_ConfigPVD

/**
  * @brief Configure the voltage threshold detected by the Power Voltage Detector (PVD).
  * @param sConfigPVD: pointer to a PWR_PVDTypeDef structure that contains the PVD 
  *        configuration information.
  * @note Refer to the electrical characteristics of your device datasheet for
  *         more details about the voltage thresholds corresponding to each
  *         detection level.
  * @retval None
  */
HAL_StatusTypeDef HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD)
{
  /* Check the parameters */
  assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel));
  assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode));

  /* Set PLS bits according to PVDLevel value */
  MODIFY_REG(PWR->CR2, PWR_CR2_PLS, sConfigPVD->PVDLevel);
  
  /* Clear any previous config. Keep it clear if no event or IT mode is selected */
  __HAL_PWR_PVD_EXTI_DISABLE_EVENT();
  __HAL_PWR_PVD_EXTI_DISABLE_IT();
  __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE(); 
  __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();

  /* Configure interrupt mode */
  if((sConfigPVD->Mode & PVD_MODE_IT) == PVD_MODE_IT)
  {
    __HAL_PWR_PVD_EXTI_ENABLE_IT();
  }
  
  /* Configure event mode */
  if((sConfigPVD->Mode & PVD_MODE_EVT) == PVD_MODE_EVT)
  {
    __HAL_PWR_PVD_EXTI_ENABLE_EVENT();
  }
  
  /* Configure the edge */
  if((sConfigPVD->Mode & PVD_RISING_EDGE) == PVD_RISING_EDGE)
  {
    __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();
  }
  
  if((sConfigPVD->Mode & PVD_FALLING_EDGE) == PVD_FALLING_EDGE)
  {
    __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE();
  }
  
  return HAL_OK;
}

开发者ID:asebak，项目名称:IMU，代码行数:49，代码来源:stm32l4xx_hal_pwr.c

示例9: HAL_PWR_ConfigPVD

/**
  * @brief  Configure the voltage threshold detected by the Power Voltage Detector(PVD).
  * @param  sConfigPVD: pointer to an PWR_PVDTypeDef structure that contains the configuration
  *         information for the PVD.
  * @note   Refer to the electrical characteristics of your device datasheet for
  *         more details about the voltage threshold corresponding to each
  *         detection level.
  * @retval None
  */
void HAL_PWR_ConfigPVD(PWR_PVDTypeDef *sConfigPVD)
{
  /* Check the parameters */
  assert_param(IS_PWR_PVD_LEVEL(sConfigPVD->PVDLevel));
  assert_param(IS_PWR_PVD_MODE(sConfigPVD->Mode));

  /* Set PLS[7:5] bits according to PVDLevel value */
  MODIFY_REG(PWR->CR1, PWR_CR1_PLS, sConfigPVD->PVDLevel);

  /* Clear any previous config */
  __HAL_PWR_PVD_EXTI_DISABLE_EVENT();
  __HAL_PWR_PVD_EXTI_DISABLE_IT();
  __HAL_PWR_PVD_EXTI_DISABLE_RISING_EDGE();
  __HAL_PWR_PVD_EXTI_DISABLE_FALLING_EDGE();

  /* Configure interrupt mode */
  if((sConfigPVD->Mode & PVD_MODE_IT) == PVD_MODE_IT)
  {
    __HAL_PWR_PVD_EXTI_ENABLE_IT();
  }
  
  /* Configure event mode */
  if((sConfigPVD->Mode & PVD_MODE_EVT) == PVD_MODE_EVT)
  {
    __HAL_PWR_PVD_EXTI_ENABLE_EVENT();
  }
  
  /* Configure the edge */
  if((sConfigPVD->Mode & PVD_RISING_EDGE) == PVD_RISING_EDGE)
  {
    __HAL_PWR_PVD_EXTI_ENABLE_RISING_EDGE();
  }

  if((sConfigPVD->Mode & PVD_FALLING_EDGE) == PVD_FALLING_EDGE)
  {
    __HAL_PWR_PVD_EXTI_ENABLE_FALLING_EDGE();
  }
}

开发者ID:pichenettes，项目名称:stmlib，代码行数:47，代码来源:stm32h7xx_hal_pwr.c

注：本文中的IS_PWR_PVD_LEVEL函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ IS_PWR_REGULATOR函数代码示例发布时间：2022-05-30

C++ IS_PRINTABLE函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：18257|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9673|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8175|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8547|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8455|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9387|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8427|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7861|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8411|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7394|2022-11-06

客服电话

电子邮件

C++ IS_PWR_PVD_LEVEL函数代码示例

示例1: HAL_PWR_PVDConfig

示例2: HAL_PWR_PVDConfig

示例3: PWR_PVDLevelConfig

示例4: PWR_PVDLevelConfig

示例5: PWR_PVDLevelConfig

示例6: PWR_PVDLevelConfig

示例7: HAL_PWR_PVDConfig

示例8: HAL_PWR_ConfigPVD

示例9: HAL_PWR_ConfigPVD

请发表评论

全部评论

上一篇：

下一篇：

GitbookIO/gitbook:

juleswhite/mobile-cloud-asgn1

颜的笔顺,诠释颜的笔画,聊聊颜的部首

kyamagu/matlab-json: Use official API: h

墙壁眼睛膝盖

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053