C++ MAP_GPIOPinWrite函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中MAP_GPIOPinWrite函数的典型用法代码示例。如果您正苦于以下问题：C++ MAP_GPIOPinWrite函数的具体用法？C++ MAP_GPIOPinWrite怎么用？C++ MAP_GPIOPinWrite使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了MAP_GPIOPinWrite函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: enc_rcr

/**
 * Read Control Register (RCR)
 */
uint8_t enc_rcr(uint8_t reg) {
	MAP_GPIOPinWrite(ENC_CS_PORT, ENC_CS, 0);
	spi_send(reg);
	uint8_t b = spi_send(0xFF);
	MAP_GPIOPinWrite(ENC_CS_PORT, ENC_CS, ENC_CS);
	return b;
}

开发者ID:mota37，项目名称:Modbus，代码行数:10，代码来源:enc28j60.c

示例2: initLEDs

//*****************************************************************************
//
//! Initialize LEDs
//!
//! \param  none
//!
//! \return none
//!
//! \brief  Initializes LED Ports and Pins
//
//*****************************************************************************
void initLEDs()
{
	// Enable use of PORTF to toggle LED and disable interrupt on this port
	MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
    //
    // Unlock PF0 so we can change it to a GPIO input
    // Once we have enabled (unlocked) the commit register then re-lock it
    // to prevent further changes.  PF0 is muxed with NMI thus a special case.
    //
    HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = GPIO_LOCK_KEY_DD;
    HWREG(GPIO_PORTF_BASE + GPIO_O_CR) |= 0x01;
    HWREG(GPIO_PORTF_BASE + GPIO_O_LOCK) = 0;

    
	MAP_GPIOPinIntDisable(GPIO_PORTF_BASE, 0xFF);
	
	// Configure Red LED
	MAP_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1);
	MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1, PIN_LOW); 
	
	// Configure Blue LED
	MAP_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2);
	MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, PIN_LOW); 
	
	// Configure Green LED
	MAP_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3);
	MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, PIN_LOW); 
	
    
    // Button inputs
	ROM_GPIODirModeSet(GPIO_PORTF_BASE, GPIO_PIN_0 | GPIO_PIN_4, GPIO_DIR_MODE_IN);
    ROM_GPIOPadConfigSet(GPIO_PORTF_BASE, GPIO_PIN_0 | GPIO_PIN_4, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);

}

开发者ID:rbasoalto，项目名称:wifi-stellaris-gcc，代码行数:45，代码来源:board.c

示例3: arch_GpioSet

void arch_GpioSet(uint_t nPort, uint_t nPin, uint_t nHL)
{

	if (nHL)
		MAP_GPIOPinWrite(arch_GpioPortBase(nPort), BITMASK(nPin), 0xFF);
	else
		MAP_GPIOPinWrite(arch_GpioPortBase(nPort), BITMASK(nPin), 0);
}

开发者ID:comrid1987，项目名称:jb3500，代码行数:8，代码来源:arch_gpio.c

示例4: enc_bfc

/**
 * Bit Field Clear.
 * Clear the bits of argument 'mask' in the register 'reg'.
 * Not valid for MAC and MII registers.
 */
void enc_bfc(uint8_t reg, uint8_t mask) {

	MAP_GPIOPinWrite(ENC_CS_PORT, ENC_CS, 0);
	spi_send(0xA0 | reg);
	spi_send(mask);

	MAP_GPIOPinWrite(ENC_CS_PORT, ENC_CS, ENC_CS);
}

开发者ID:mota37，项目名称:Modbus，代码行数:13，代码来源:enc28j60.c

示例5: turnLedOn

//*****************************************************************************
//
// This function turns the USER LED ON/OFF
// 
//!
//! \param  ledNum is the LED Number
//!
//! \return none
//!
//! \brief  Turns a specific LED Off
//
//*****************************************************************************
void turnLedOn(char ledNum)
{
	
	switch (ledNum)
	{
		//RED
	case 1:
		//turn other blue and green LED off
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, PIN_LOW);
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, PIN_LOW);
		//turn RED LED on
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1, PIN_HIGH);
		break;
		
		//Blue
	case 2:
		//turn other red and green LED off
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1, PIN_LOW);
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, PIN_LOW);
		//turn BLUE LED on
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, PIN_HIGH);
		break;
		
		//Green
	case 3:
		//turn other red and blue LED off
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1, PIN_LOW);
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, PIN_LOW);
		//turn GREEN LED on
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, PIN_HIGH);
		break;
	}
}

开发者ID:rbasoalto，项目名称:wifi-stellaris-gcc，代码行数:45，代码来源:board.c

示例6: WriteWlanPin

void WriteWlanPin( unsigned char val )
{
	if(val)
	{
  		MAP_GPIOPinWrite(SPI_GPIO_IRQ_BASE, SPI_EN_PIN,PIN_HIGH);
	}
	else
	{
  		MAP_GPIOPinWrite(SPI_GPIO_IRQ_BASE, SPI_EN_PIN, PIN_LOW);
	}
	
}

开发者ID:rbasoalto，项目名称:wifi-stellaris-gcc，代码行数:12，代码来源:board.c

示例7: platform_pio_op

pio_type platform_pio_op( unsigned port, pio_type pinmask, int op )
{
    pio_type retval = 1, base = pio_base[ port ];

    switch( op )
    {
    case PLATFORM_IO_PORT_SET_VALUE:
        MAP_GPIOPinWrite( base, 0xFF, pinmask );
        break;

    case PLATFORM_IO_PIN_SET:
        MAP_GPIOPinWrite( base, pinmask, pinmask );
        break;

    case PLATFORM_IO_PIN_CLEAR:
        MAP_GPIOPinWrite( base, pinmask, 0 );
        break;

    case PLATFORM_IO_PORT_DIR_INPUT:
        pinmask = 0xFF;
    case PLATFORM_IO_PIN_DIR_INPUT:
        MAP_GPIOPinTypeGPIOInput( base, pinmask );
        break;

    case PLATFORM_IO_PORT_DIR_OUTPUT:
        pinmask = 0xFF;
    case PLATFORM_IO_PIN_DIR_OUTPUT:
        MAP_GPIOPinTypeGPIOOutput( base, pinmask );
        break;

    case PLATFORM_IO_PORT_GET_VALUE:
        retval = MAP_GPIOPinRead( base, 0xFF );
        break;

    case PLATFORM_IO_PIN_GET:
        retval = MAP_GPIOPinRead( base, pinmask ) ? 1 : 0;
        break;

    case PLATFORM_IO_PIN_PULLUP:
    case PLATFORM_IO_PIN_PULLDOWN:
        MAP_GPIOPadConfigSet( base, pinmask, GPIO_STRENGTH_8MA, op == PLATFORM_IO_PIN_PULLUP ? GPIO_PIN_TYPE_STD_WPU : GPIO_PIN_TYPE_STD_WPD );
        break;

    case PLATFORM_IO_PIN_NOPULL:
        MAP_GPIOPadConfigSet( base, pinmask, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD );
        break;

    default:
        retval = 0;
        break;
    }
    return retval;
}

开发者ID:zhanjun，项目名称:elua，代码行数:53，代码来源:platform.c

示例8: enc_rbm

/**
 * Read Buffer Memory.
 */
void enc_rbm(uint8_t *buf, uint16_t count) {

	MAP_GPIOPinWrite(ENC_CS_PORT, ENC_CS, 0);

	spi_send(0x20 | 0x1A);
	int i;
	for (i = 0; i < count; i++) {
		*buf = spi_send(0xFF);
		buf++;
	}

	MAP_GPIOPinWrite(ENC_CS_PORT, ENC_CS, ENC_CS);
}

开发者ID:mota37，项目名称:Modbus，代码行数:16，代码来源:enc28j60.c

示例9: enc_wbm

/**
 * Write Buffer Memory.
 */
void enc_wbm(const uint8_t *buf, uint16_t count) {

	MAP_GPIOPinWrite(ENC_CS_PORT, ENC_CS, 0);

	spi_send(0x60 | 0x1A);
	int i;
	for (i = 0; i < count; i++) {
		spi_send(*buf);
		buf++;
	}


	MAP_GPIOPinWrite(ENC_CS_PORT, ENC_CS, ENC_CS);
}

开发者ID:mota37，项目名称:Modbus，代码行数:17，代码来源:enc28j60.c

示例10: AntennaSelect

void AntennaSelect(unsigned char ucAntNum)
{

    if(ucAntNum == 1)
    {
         MAP_GPIOPinWrite(GPIOA3_BASE, 0xC, 0x8);
    }
    else if(ucAntNum == 2)
    {
        MAP_GPIOPinWrite(GPIOA3_BASE, 0xC, 0x4);
    }

    return;
}

开发者ID:Balu1991，项目名称:Wifly_Light，代码行数:14，代码来源:main.c

示例11: antenna_select

void antenna_select (antenna_type_t _antenna) {
    if (_antenna == ANTENNA_TYPE_INTERNAL) {
        MAP_GPIOPinWrite(GPIOA3_BASE, 0x0C, 0x04);
        // also configure the pull-up and pull-down accordingly
        HWREG(REG_PAD_CONFIG_26) = ((HWREG(REG_PAD_CONFIG_26) & ~PAD_TYPE_MASK)) | PIN_TYPE_STD_PU;
        HWREG(REG_PAD_CONFIG_27) = ((HWREG(REG_PAD_CONFIG_27) & ~PAD_TYPE_MASK)) | PIN_TYPE_STD_PD;
    } else {
        MAP_GPIOPinWrite(GPIOA3_BASE, 0x0C, 0x08);
        // also configure the pull-up and pull-down accordingly
        HWREG(REG_PAD_CONFIG_26) = ((HWREG(REG_PAD_CONFIG_26) & ~PAD_TYPE_MASK)) | PIN_TYPE_STD_PD;
        HWREG(REG_PAD_CONFIG_27) = ((HWREG(REG_PAD_CONFIG_27) & ~PAD_TYPE_MASK)) | PIN_TYPE_STD_PU;
    }
    antenna_type_selected = _antenna;
}

开发者ID:AriZuu，项目名称:micropython，代码行数:14，代码来源:antenna.c

示例12: pin_value

/// \method value([value])
/// Get or set the digital logic level of the pin:
///
///   - With no arguments, return 0 or 1 depending on the logic level of the pin.
///   - With `value` given, set the logic level of the pin.  `value` can be
///   anything that converts to a boolean.  If it converts to `True`, the pin
///   is set high, otherwise it is set low.
STATIC mp_obj_t pin_value(mp_uint_t n_args, const mp_obj_t *args) {
    pin_obj_t *self = args[0];
    if (n_args == 1) {
        // get the pin value
        return MP_OBJ_NEW_SMALL_INT(MAP_GPIOPinRead(self->port, self->bit) ? 1 : 0);
    } else {
        // set the pin value
        if (mp_obj_is_true(args[1])) {
            MAP_GPIOPinWrite(self->port, self->bit, self->bit);
        } else {
            MAP_GPIOPinWrite(self->port, self->bit, 0);
        }
        return mp_const_none;
    }
}

开发者ID:chenyaqiuqiu，项目名称:micropython，代码行数:22，代码来源:pybpin.c

示例13: SSITRF79x0Init

//*****************************************************************************
//
// Initializes the SSI port and determines if the TRF79x0 is available.
//
// This function must be called prior to any other function offered by the
// TRF79x0.  It configures the SSI port to run in Motorola/Freescale
// mode.
//
// \return None.
//
//*****************************************************************************
void
SSITRF79x0Init(void)
{
    //
    // Enable the peripherals used to drive the TRF79x0 on SSI.
    //
    MAP_SysCtlPeripheralEnable(TRF79X0_SSI_PERIPH);

    //
    // Enable the GPIO peripherals associated with the SSI.
    //
    MAP_SysCtlPeripheralEnable(TRF79X0_CLK_PERIPH);
    MAP_SysCtlPeripheralEnable(TRF79X0_RX_PERIPH);
    MAP_SysCtlPeripheralEnable(TRF79X0_TX_PERIPH);
    MAP_SysCtlPeripheralEnable(TRF79X0_CS_PERIPH);

    //
    // Configure the appropriate pins to be SSI instead of GPIO.  The CS
    // is configured as GPIO to support TRF79x0 SPI requirements for R/W
    // access.
    //
    MAP_GPIOPinConfigure(TRF79X0_CLK_CONFIG);
    MAP_GPIOPinConfigure(TRF79X0_RX_CONFIG);
    MAP_GPIOPinConfigure(TRF79X0_TX_CONFIG);
    MAP_GPIOPinTypeSSI(TRF79X0_CLK_BASE, TRF79X0_CLK_PIN);
    MAP_GPIOPinTypeSSI(TRF79X0_RX_BASE, TRF79X0_RX_PIN);
    MAP_GPIOPinTypeSSI(TRF79X0_TX_BASE, TRF79X0_TX_PIN);
    MAP_GPIOPinTypeGPIOOutput(TRF79X0_CS_BASE, TRF79X0_CS_PIN);

    MAP_GPIOPadConfigSet(TRF79X0_CLK_BASE, TRF79X0_CLK_PIN,
                         GPIO_STRENGTH_4MA, GPIO_PIN_TYPE_STD_WPU);
    MAP_GPIOPadConfigSet(TRF79X0_RX_BASE, TRF79X0_RX_PIN,
                         GPIO_STRENGTH_4MA, GPIO_PIN_TYPE_STD_WPU);
    MAP_GPIOPadConfigSet(TRF79X0_TX_BASE, TRF79X0_TX_PIN,
                         GPIO_STRENGTH_4MA, GPIO_PIN_TYPE_STD_WPU);

    //
    // Deassert the SSI chip selects TRF79x0.
    //
    MAP_GPIOPinWrite(TRF79X0_CS_BASE, TRF79X0_CS_PIN, TRF79X0_CS_PIN);

    //
    // Configure the SSI port for 2MHz operation.
    //
    MAP_SSIConfigSetExpClk(TRF79X0_SSI_BASE, g_ui32SysClk,
                           SSI_FRF_MOTO_MODE_0, SSI_MODE_MASTER, SSI_CLK_RATE,
                           8);

    if(RF_DAUGHTER_TRF7970) {
        //
        // Switch from SPH=0 to SPH=1.  Required for TRF7970.
        //
        HWREG(TRF79X0_SSI_BASE + SSI_O_CR0) |= SSI_CR0_SPH;
    }

    //
    // Enable the SSI controller.
    //
    MAP_SSIEnable(TRF79X0_SSI_BASE);
}

开发者ID:peterliu2，项目名称:tivaWare，代码行数:71，代码来源:ssitrf79x0.c

示例14: enc28j60_comm_init

static void
enc28j60_comm_init(void) {
  MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
  MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
  MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOA);
  MAP_GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE, ENC_CS | ENC_RESET);
  MAP_GPIOPinTypeGPIOOutput(GPIO_PORTA_BASE, SRAM_CS);
//  MAP_GPIOPinTypeGPIOOutput(GPIO_PORTA_BASE, ENC_CS | ENC_RESET | SRAM_CS);
  MAP_GPIOPinTypeGPIOInput(GPIO_PORTE_BASE, ENC_INT);

  MAP_GPIOPinWrite(GPIO_PORTB_BASE, ENC_RESET, 0);
  MAP_GPIOPinWrite(ENC_CS_PORT, ENC_CS, ENC_CS);
  MAP_GPIOPinWrite(GPIO_PORTA_BASE, SRAM_CS, SRAM_CS);
  SysCtlDelay(((SysCtlClockGet() / 3) / 10)); //100ms delay
  MAP_GPIOPinWrite(GPIO_PORTB_BASE, ENC_RESET, ENC_RESET);
}

开发者ID:cubeberg，项目名称:HomeAutomation，代码行数:16，代码来源:main.c

示例15: main

int main(){

	// System clock set to run at 50 MHz from PLL with crystal ref.
	// With EK-TM4C123GXL Launchpad, no need to change SYSCTL_XTAL_16MHZ to anything else
	MAP_SysCtlClockSet(SYSCTL_SYSDIV_4|SYSCTL_USE_PLL|SYSCTL_XTAL_16MHZ|SYSCTL_OSC_MAIN);
	MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
	MAP_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, LED_RED|LED_BLUE|LED_GREEN);

	while(1){
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, LED_RED|LED_GREEN|LED_BLUE, LED_GREEN|LED_RED|LED_BLUE);
		// SysCtlDelay and ROM_SysCtlDelay behave differently, see http://e2e.ti.com/support/microcontrollers/tiva_arm/f/908/t/256106.aspx
		MAP_SysCtlDelay(2333333);	// Number of loop iterations to perform @ 3 cycles/loop using ROM. Not Accurate. Input = (DesiredTime*ClockFrequency)/3
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, LED_RED|LED_GREEN|LED_BLUE, 0);
		MAP_SysCtlDelay(16333333);
	}
}

开发者ID:chaitanya4b3，项目名称:Tiva-Test，代码行数:16，代码来源:blink.c

示例16: enc28j60_comm_init

static void enc28j60_comm_init(void) {
  MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOB);
  MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOE);
  MAP_GPIOPinTypeGPIOOutput(GPIO_PORTB_BASE, ENC_CS);
  MAP_GPIOPinTypeGPIOInput(GPIO_PORTE_BASE, ENC_INT);

  MAP_GPIOPinWrite(ENC_CS_PORT, ENC_CS, ENC_CS);
}

开发者ID:brians444，项目名称:tiva-ads1246-lwip，代码行数:8，代码来源:main.c

示例17: pin_obj_configure

STATIC void pin_obj_configure (const pin_obj_t *self) {
    uint32_t type;
    if (self->mode == PIN_TYPE_ANALOG) {
        type = PIN_TYPE_ANALOG;
    } else {
        type = self->pull;
        uint32_t direction = self->mode;
        if (direction == PIN_TYPE_OD || direction == GPIO_DIR_MODE_ALT_OD) {
            direction = GPIO_DIR_MODE_OUT;
            type |= PIN_TYPE_OD;
        }
        if (self->mode != GPIO_DIR_MODE_ALT && self->mode != GPIO_DIR_MODE_ALT_OD) {
            // enable the peripheral clock for the GPIO port of this pin
            switch (self->port) {
            case PORT_A0:
                MAP_PRCMPeripheralClkEnable(PRCM_GPIOA0, PRCM_RUN_MODE_CLK | PRCM_SLP_MODE_CLK);
                break;
            case PORT_A1:
                MAP_PRCMPeripheralClkEnable(PRCM_GPIOA1, PRCM_RUN_MODE_CLK | PRCM_SLP_MODE_CLK);
                break;
            case PORT_A2:
                MAP_PRCMPeripheralClkEnable(PRCM_GPIOA2, PRCM_RUN_MODE_CLK | PRCM_SLP_MODE_CLK);
                break;
            case PORT_A3:
                MAP_PRCMPeripheralClkEnable(PRCM_GPIOA3, PRCM_RUN_MODE_CLK | PRCM_SLP_MODE_CLK);
                break;
            default:
                break;
            }

            // set the pin value
            if (self->value) {
                MAP_GPIOPinWrite(self->port, self->bit, self->bit);
            } else {
                MAP_GPIOPinWrite(self->port, self->bit, 0);
            }

            // configure the direction
            MAP_GPIODirModeSet(self->port, self->bit, direction);
        }
        // now set the alternate function
        MAP_PinModeSet (self->pin_num, self->af);
    }
    MAP_PinConfigSet(self->pin_num, self->strength, type);
}

开发者ID:rubencabrera，项目名称:micropython，代码行数:45，代码来源:pybpin.c

示例18: turnLedOff

//*****************************************************************************
//
//! Turn LED Off
//!
//! \param  ledNum is the LED Number
//!
//! \return none
//!
//! \brief  Turns a specific LED Off
//
//*****************************************************************************    
void turnLedOff(char ledNum)
{
	
	switch (ledNum)
	{
		//RED
	case 1:
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1, PIN_LOW);
		
		//Blue
	case 2:
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, PIN_LOW);
		
		//Green
	case 3:
		MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, PIN_LOW);
	}
}

开发者ID:rbasoalto，项目名称:wifi-stellaris-gcc，代码行数:29，代码来源:board.c

示例19: initLEDs

//*****************************************************************************
//
//! Initialize LEDs
//!
//! \param  none
//!
//! \return none
//!
//! \brief  Initializes LED Ports and Pins
//
//*****************************************************************************
void initLEDs()
{
	// Enable use of PORTF to toggle LED and disable interrupt on this port
	MAP_SysCtlPeripheralEnable(SYSCTL_PERIPH_GPIOF);
	MAP_GPIOPinIntDisable(GPIO_PORTF_BASE, 0xFF);
	
	// Configure Red LED
	MAP_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_1);
	MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_1, PIN_LOW); 
	
	// Configure Blue LED
	MAP_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_2);
	MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_2, PIN_LOW); 
	
	// Configure Green LED
	MAP_GPIOPinTypeGPIOOutput(GPIO_PORTF_BASE, GPIO_PIN_3);
	MAP_GPIOPinWrite(GPIO_PORTF_BASE, GPIO_PIN_3, PIN_LOW); 
	
}

开发者ID:ianjuch，项目名称:ee149，代码行数:30，代码来源:board.c

示例20: wait_while_blinking

//*****************************************************************************
//! Wait while the safe mode pin is being held high and blink the system led
//! with the specified period
//*****************************************************************************
static bool wait_while_blinking (uint32_t wait_time, uint32_t period, bool force_wait) {
    _u32 count;
    for (count = 0; (force_wait || MAP_GPIOPinRead(MICROPY_SAFE_BOOT_PORT, MICROPY_SAFE_BOOT_PORT_PIN)) &&
         ((period * count) < wait_time); count++) {
        // toogle the led
        MAP_GPIOPinWrite(MICROPY_SYS_LED_PORT, MICROPY_SYS_LED_PORT_PIN, ~MAP_GPIOPinRead(MICROPY_SYS_LED_PORT, MICROPY_SYS_LED_PORT_PIN));
        UtilsDelay(UTILS_DELAY_US_TO_COUNT(period * 1000));
    }
    return MAP_GPIOPinRead(MICROPY_SAFE_BOOT_PORT, MICROPY_SAFE_BOOT_PORT_PIN) ? true : false;
}

开发者ID:Ga-vin，项目名称:micropython，代码行数:14，代码来源:main.c

注：本文中的MAP_GPIOPinWrite函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ MAP_IntEnable函数代码示例发布时间：2022-05-30

C++ MAPIFreeBuffer函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：18222|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9658|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8173|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8543|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8450|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9375|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8420|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7855|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8405|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7392|2022-11-06

客服电话

电子邮件

C++ MAP_GPIOPinWrite函数代码示例

示例1: enc_rcr

示例2: initLEDs

示例3: arch_GpioSet

示例4: enc_bfc

示例5: turnLedOn

示例6: WriteWlanPin

示例7: platform_pio_op

示例8: enc_rbm

示例9: enc_wbm

示例10: AntennaSelect

示例11: antenna_select

示例12: pin_value

示例13: SSITRF79x0Init

示例14: enc28j60_comm_init

示例15: main

示例16: enc28j60_comm_init

示例17: pin_obj_configure

示例18: turnLedOff

示例19: initLEDs

示例20: wait_while_blinking

请发表评论

全部评论

上一篇：

下一篇：

librespeed/speedtest: Self-hosted Speedt

CVE-2022-34965

avehtari/BDA_m_demos: Bayesian Data Anal

四维彩超怎么看性别？四维看男孩女孩诀窍

个体户条例实施细则，2020 最新个体工商户

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053