C++ MAP_IntVTableBaseSet函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中MAP_IntVTableBaseSet函数的典型用法代码示例。如果您正苦于以下问题：C++ MAP_IntVTableBaseSet函数的具体用法？C++ MAP_IntVTableBaseSet怎么用？C++ MAP_IntVTableBaseSet使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了MAP_IntVTableBaseSet函数的18个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: BoardInit

//*****************************************************************************
//
//! Board Initialization & Configuration
//!
//! \param  None
//!
//! \return None
//
//*****************************************************************************
static void
BoardInit(void)
{
/* In case of TI-RTOS vector table is initialize by OS itself */
#ifndef USE_TIRTOS
    //
    // Set vector table base
    //
#if defined(ccs)
    MAP_IntVTableBaseSet((unsigned long)&g_pfnVectors[0]);
#endif  //ccs
#if defined(ewarm)
    MAP_IntVTableBaseSet((unsigned long)&__vector_table);
#endif  //ewarm
    
#endif  //USE_TIRTOS
    
    //
    // Enable Processor
    //
    MAP_IntMasterEnable();
    MAP_IntEnable(FAULT_SYSTICK);

    PRCMCC3200MCUInit();
}

开发者ID:JamesHyunKim，项目名称:quickstart-samples，代码行数:34，代码来源:main.c

示例2: BoardInit

//*****************************************************************************
//
//! Board Initialization & Configuration
//!
//! \param  None
//!
//! \return None
//
//*****************************************************************************
static void
BoardInit(void)
{
    //
    // Set vector table base
    //
#ifndef USE_TIRTOS
  //
  // Set vector table base
  //
#if defined(ccs) || defined(gcc)
    MAP_IntVTableBaseSet((unsigned long)&g_pfnVectors[0]);
#endif
#if defined(ewarm)
    MAP_IntVTableBaseSet((unsigned long)&__vector_table);
#endif
#endif

    //
    // Enable Processor
    //
    MAP_IntMasterEnable();
    MAP_IntEnable(FAULT_SYSTICK);

    PRCMCC3200MCUInit();
}

开发者ID:oter，项目名称:BSPTools，代码行数:35，代码来源:main.c

示例3: initBoard

void initBoard() {
#ifndef USE_TIRTOS
#if defined(ccs) || defined(gcc)
    MAP_IntVTableBaseSet((unsigned long) &g_pfnVectors[0]);
#endif
#if defined(ewarm)
    MAP_IntVTableBaseSet((unsigned long)&__vector_table);
#endif
#endif

    MAP_IntMasterEnable();
    MAP_IntEnable(FAULT_SYSTICK);

    PRCMCC3200MCUInit();

    PinMuxConfig();
    GPIO_IF_LedConfigure(LED1);
    GPIO_IF_LedOff(MCU_RED_LED_GPIO);

    InitTerm();
    ClearTerm();

    UART_PRINT("Blink - Parse for IoT sample application\r\n");
    UART_PRINT("----------------------------------------\r\n");
    UART_PRINT("\r\n");
    UART_PRINT("[Blink] Board init\r\n");

    // start the spawn task
    short status = VStartSimpleLinkSpawnTask(SPAWN_TASK_PRIORITY);
    if (status < 0) {
        UART_PRINT("[Blink] Spawn task failed\r\n");
        ERR_PRINT(status);
        LOOP_FOREVER();
    }

    // initialize the I2C bus
    status = I2C_IF_Open(I2C_MASTER_MODE_FST);
    if (status < 0) {
        UART_PRINT("[Blink] I2C opening error\r\n");
        ERR_PRINT(status);
        LOOP_FOREVER();
    }

    UART_PRINT("[Blink] Device                    : TI SimpleLink CC3200\r\n");
#ifdef USE_TIRTOS
    UART_PRINT("[Blink] Operating system          : TI-RTOS\r\n");
#endif
#ifdef USE_FREERTOS
    UART_PRINT("[Blink] Operating system          : FreeRTOS\r\n");
#endif
#ifndef SL_PLATFORM_MULTI_THREADED
    UART_PRINT("[Blink] Operating system          : None\r\n");
#endif
}

开发者ID:AnjaneyuluAdepu，项目名称:parse-embedded-sdks，代码行数:54，代码来源:board.c

示例4: SysPlatformConfig

void SysPlatformConfig(void)
/********************************************************************************/
{
#if defined(COMPLIER_CCS)
    MAP_IntVTableBaseSet((unsigned long)&g_pfnVectors[0]);
#elif defined(COMPLIER_EARM)
    MAP_IntVTableBaseSet((unsigned long)&__vector_table);
#endif
    
    /* Enable Processor */
    MAP_IntMasterEnable();
    MAP_IntEnable(FAULT_SYSTICK);

    PRCMCC3200MCUInit();
}

开发者ID:yuanzhen-liu，项目名称:Bootloader，代码行数:15，代码来源:PlatformStartup.c

示例5: bootmgr_board_init

//*****************************************************************************
//! Board Initialization & Configuration
//*****************************************************************************
static void bootmgr_board_init(void) {
    // set the vector table base
    MAP_IntVTableBaseSet((unsigned long)&g_pfnVectors[0]);

    // enable processor interrupts
    MAP_IntMasterEnable();
    MAP_IntEnable(FAULT_SYSTICK);

    // mandatory MCU initialization
    PRCMCC3200MCUInit();

    // clear all the special bits, since we can't trust their content after reset
    // except for the WDT reset one!!
    PRCMClearSpecialBit(PRCM_SAFE_BOOT_BIT);
    PRCMClearSpecialBit(PRCM_FIRST_BOOT_BIT);

    // check the reset after clearing the special bits
    mperror_bootloader_check_reset_cause();

#if MICROPY_HW_ANTENNA_DIVERSITY
    // configure the antenna selection pins
    antenna_init0();
#endif

    // enable the data hashing engine
    CRYPTOHASH_Init();

    // init the system led and the system switch
    mperror_init0();
}

开发者ID:19emtuck，项目名称:micropython，代码行数:33，代码来源:main.c

示例6: main

int main() {
  MAP_IntVTableBaseSet((unsigned long) &g_pfnVectors[0]);
  MAP_IntEnable(FAULT_SYSTICK);
  MAP_IntMasterEnable();
  PRCMCC3200MCUInit();

  cc3200_leds_init();

  /* Console UART init. */
  MAP_PRCMPeripheralClkEnable(CONSOLE_UART_PERIPH, PRCM_RUN_MODE_CLK);
  MAP_PinTypeUART(PIN_55, PIN_MODE_3); /* PIN_55 -> UART0_TX */
  MAP_PinTypeUART(PIN_57, PIN_MODE_3); /* PIN_57 -> UART0_RX */
  MAP_UARTConfigSetExpClk(
      CONSOLE_UART, MAP_PRCMPeripheralClockGet(CONSOLE_UART_PERIPH),
      CONSOLE_BAUD_RATE,
      (UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE | UART_CONFIG_PAR_NONE));
  MAP_UARTFIFODisable(CONSOLE_UART);

  setvbuf(stdout, NULL, _IONBF, 0);
  setvbuf(stderr, NULL, _IONBF, 0);

  VStartSimpleLinkSpawnTask(8);
  osi_TaskCreate(v7_task, (const signed char *) "v7", V7_STACK_SIZE + 256, NULL,
                 3, NULL);
  osi_TaskCreate(blinkenlights_task, (const signed char *) "blink", 256, NULL,
                 9, NULL);
  osi_start();

  return 0;
}

开发者ID:GDI123，项目名称:smart.js，代码行数:30，代码来源:main.c

示例7: bootmgr_board_init

//*****************************************************************************
//! Board Initialization & Configuration
//*****************************************************************************
static void bootmgr_board_init(void) {
    // set the vector table base
    MAP_IntVTableBaseSet((unsigned long)&g_pfnVectors[0]);

    // enable processor interrupts
    MAP_IntMasterEnable();
    MAP_IntEnable(FAULT_SYSTICK);

    // mandatory MCU initialization
    PRCMCC3200MCUInit();

    mperror_bootloader_check_reset_cause();

#if MICROPY_HW_ANTENNA_DIVERSITY
    // configure the antenna selection pins
    antenna_init0();
#endif

    // enable the data hashing engine
    CRYPTOHASH_Init();

    // init the system led and the system switch
    mperror_init0();

    // clear the safe boot flag, since we can't trust its content after reset
    PRCMClearSafeBootRequest();
}

开发者ID:Ga-vin，项目名称:micropython，代码行数:30，代码来源:main.c

示例8: BoardInit

static void BoardInit(void)
{

  MAP_IntVTableBaseSet((unsigned long)&g_pfnVectors[0]);

  MAP_IntMasterEnable();
  MAP_IntEnable(FAULT_SYSTICK);

  PRCMCC3200MCUInit();
}

开发者ID:Eterneco，项目名称:iot_control，代码行数:10，代码来源:main.c

示例9: BoardInit

//*****************************************************************************
//
//! Board Initialization & Configuration
//!
//! \param  None
//!
//! \return None
//
//*****************************************************************************
static void BoardInit(void)
{
    // Set vector table base
    MAP_IntVTableBaseSet((unsigned long)&g_pfnVectors[0]);

    // Enable Processor
    MAP_IntMasterEnable();
    MAP_IntEnable(FAULT_SYSTICK);

    PRCMCC3200MCUInit();
}

开发者ID:tzhenghao，项目名称:TimerInterruptsOnCC3200，代码行数:20，代码来源:main.c

示例10: main

int main() {
#ifndef USE_TIRTOS
  MAP_IntVTableBaseSet((unsigned long) &g_pfnVectors[0]);
#endif
  MAP_IntEnable(FAULT_SYSTICK);
  MAP_IntMasterEnable();
  PRCMCC3200MCUInit();

  /* Console UART init. */
  MAP_PRCMPeripheralClkEnable(CONSOLE_UART_PERIPH, PRCM_RUN_MODE_CLK);
  MAP_PinTypeUART(PIN_55, PIN_MODE_3); /* PIN_55 -> UART0_TX */
  MAP_PinTypeUART(PIN_57, PIN_MODE_3); /* PIN_57 -> UART0_RX */
  MAP_UARTConfigSetExpClk(
      CONSOLE_UART, MAP_PRCMPeripheralClockGet(CONSOLE_UART_PERIPH),
      CONSOLE_BAUD_RATE,
      (UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE | UART_CONFIG_PAR_NONE));
  MAP_UARTFIFOLevelSet(CONSOLE_UART, UART_FIFO_TX1_8, UART_FIFO_RX4_8);
  MAP_UARTFIFOEnable(CONSOLE_UART);

  setvbuf(stdout, NULL, _IOLBF, 0);
  setvbuf(stderr, NULL, _IOLBF, 0);
  cs_log_set_level(LL_INFO);
  cs_log_set_file(stdout);

  LOG(LL_INFO, ("Hello, world!"));

  MAP_PinTypeI2C(PIN_01, PIN_MODE_1); /* SDA */
  MAP_PinTypeI2C(PIN_02, PIN_MODE_1); /* SCL */
  I2C_IF_Open(I2C_MASTER_MODE_FST);

  /* Set up the red LED. Note that amber and green cannot be used as they share
   * pins with I2C. */
  MAP_PRCMPeripheralClkEnable(PRCM_GPIOA1, PRCM_RUN_MODE_CLK);
  MAP_PinTypeGPIO(PIN_64, PIN_MODE_0, false);
  MAP_GPIODirModeSet(GPIOA1_BASE, 0x2, GPIO_DIR_MODE_OUT);
  GPIO_IF_LedConfigure(LED1);
  GPIO_IF_LedOn(MCU_RED_LED_GPIO);

  if (VStartSimpleLinkSpawnTask(8) != 0) {
    LOG(LL_ERROR, ("Failed to create SL task"));
  }

  if (!mg_start_task(MG_TASK_PRIORITY, MG_TASK_STACK_SIZE, mg_init)) {
    LOG(LL_ERROR, ("Failed to create MG task"));
  }

  osi_start();

  return 0;
}

开发者ID:cobookman，项目名称:mongoose，代码行数:50，代码来源:main.c

示例11: BoardInit

static void BoardInit()
{
    MAP_IntVTableBaseSet((unsigned long)&g_pfnVectors[0]);

    MAP_IntMasterEnable();
    MAP_IntEnable(FAULT_SYSTICK);

    PRCMCC3200MCUInit();

    UDMAInit();

    MAP_PRCMPeripheralClkEnable(PRCM_UARTA0, PRCM_RUN_MODE_CLK);
    MAP_PinTypeUART(PIN_55, PIN_MODE_3);
    MAP_PinTypeUART(PIN_57, PIN_MODE_3);

    InitTerm();
}

开发者ID:BillTheBest，项目名称:sample-apps，代码行数:17，代码来源:cc32xx_support.c

示例12: BoardInit

//*****************************************************************************
//
//! Board Initialization & Configuration
//!
//! \param  None
//!
//! \return None
//
//*****************************************************************************
static void
BoardInit(void)
{
/* In case of TI-RTOS vector table is initialize by OS itself */
    //
    // Set vector table base
    //
    MAP_IntVTableBaseSet((unsigned long)&g_pfnVectors[0]);

    //
    // Enable Processor
    //
    MAP_IntMasterEnable();
    MAP_IntEnable(FAULT_SYSTICK);

    PRCMCC3200MCUInit();
}

开发者ID:CaptFrank，项目名称:CC3200-Linux-SDK，代码行数:26，代码来源:main.c

示例13: bootmgr_board_init

//*****************************************************************************
//! Board Initialization & Configuration
//*****************************************************************************
static void bootmgr_board_init(void) {
    // Set vector table base
    MAP_IntVTableBaseSet((unsigned long)&g_pfnVectors[0]);

    // Enable Processor Interrupts
    MAP_IntMasterEnable();
    MAP_IntEnable(FAULT_SYSTICK);

    // Mandatory MCU Initialization
    PRCMCC3200MCUInit();

    mperror_bootloader_check_reset_cause();

    // Enable the Data Hashing Engine
    HASH_Init();

    // Init the system led and the system switch
    mperror_init0();

    // clear the safe boot flag, since we can't trust its content after reset
    PRCMClearSafeBootRequest();
}

开发者ID:Dreamapple，项目名称:micropython，代码行数:25，代码来源:main.c

示例14: main

int main()
{
  MAP_IntVTableBaseSet((unsigned long)vectors);
  MAP_IntMasterEnable();
  MAP_IntEnable(FAULT_SYSTICK);
  PRCMCC3200MCUInit();
#ifdef UART_LOG
  MAP_PRCMPeripheralClkEnable(PRCM_UART_TERM, PRCM_RUN_MODE_CLK);
  MAP_PinTypeUART(PIN_TERM_TX, PIN_TERM_TX_MODE);
  MAP_PinTypeUART(PIN_TERM_RX, PIN_TERM_RX_MODE);
  MAP_UARTConfigSetExpClk(UART_TERM,
                          MAP_PRCMPeripheralClockGet(PRCM_UART_TERM),
                          115200,
                          (UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE |UART_CONFIG_PAR_NONE));
#endif

  MonitorLoop();

  asm(" BKPT");
  while ( 1 );

  return 0;
}

开发者ID:M3gaFr3ak，项目名称:found-bits，代码行数:23，代码来源:main.c

示例15: bootmgr_board_init

//*****************************************************************************
//! Board Initialization & Configuration
//*****************************************************************************
static void bootmgr_board_init(void) {
    // Set vector table base
    MAP_IntVTableBaseSet((unsigned long)&g_pfnVectors[0]);

    // Enable Processor Interrupts
    MAP_IntMasterEnable();
    MAP_IntEnable(FAULT_SYSTICK);

    // Mandatory MCU Initialization
    PRCMCC3200MCUInit();

    pybwdt_check_reset_cause();

    // Enable the Data Hashing Engine
    HASH_Init();

    // Init the system led and the system switch
    mperror_init0();

    // clear the safe boot request, since we should not trust
    // the register's state after reset
    mperror_clear_safe_boot();
}

开发者ID:jasongwq，项目名称:micropython，代码行数:26，代码来源:main.c

示例16: main

//****************************************************************************
//
//! Main function
//!
//! \param none
//! 
//! This function  
//!    1. Invokes the SLHost task
//!    2. Invokes the AP Antenna Selection Task
//!
//! \return None.
//
//****************************************************************************
void main()
{
    //
    // Setup the interrupt vector table
    //
#if defined(ewarm)
    MAP_IntVTableBaseSet((unsigned long)&__vector_table);
#endif
    
    //MCU Initialization
    PRCMCC3200MCUInit();
    
    
    MAP_PRCMPeripheralClkEnable(PRCM_GPIOA3, PRCM_RUN_MODE_CLK);
    MAP_GPIODirModeSet(GPIOA3_BASE,0xC,GPIO_DIR_MODE_OUT);

    
    //
    // Configure PIN_29 for GPIOOutput
    //    
    HWREG(REG_PAD_CONFIG_26) = ((HWREG(REG_PAD_CONFIG_26) & ~(PAD_STRENGTH_MASK 
                        | PAD_TYPE_MASK)) | (0x00000020 | 0x00000000 ));
    
    //
    // Set the mode.
    //
    HWREG(REG_PAD_CONFIG_26) = (((HWREG(REG_PAD_CONFIG_26) & ~PAD_MODE_MASK) |  
                                                    0x00000000) & ~(3<<10));
    
    //
    // Set the direction
    //
    HWREG(REG_PAD_CONFIG_26) = ((HWREG(REG_PAD_CONFIG_26) & ~0xC00) | 0x00000800);
    
    
     //
    // Configure PIN_30 for GPIOOutput
    //
    HWREG(REG_PAD_CONFIG_27) = ((HWREG(REG_PAD_CONFIG_27) & ~(PAD_STRENGTH_MASK
                                | PAD_TYPE_MASK)) | (0x00000020 | 0x00000000 ));
    
    //
    // Set the mode.
    //
    HWREG(REG_PAD_CONFIG_27) = (((HWREG(REG_PAD_CONFIG_27) & ~PAD_MODE_MASK) |  
                                        0x00000000) & ~(3<<10));

    //
    // Set the direction
    //
    HWREG(REG_PAD_CONFIG_26) = ((HWREG(REG_PAD_CONFIG_27) & ~0xC00) | 0x00000800);
    
    
    //Enable Interrupt
    MAP_IntMasterEnable();
    MAP_IntEnable(FAULT_SYSTICK);
    
     //
    // Simplelinkspawntask
    //
    VStartSimpleLinkSpawnTask(SPAWN_TASK_PRIORITY);
    
    osi_TaskCreate(AntennaSelection, (signed char*)"AntennaSelection",1024,
                        NULL, APP_TASK_PRIORITY, NULL );
    
    osi_start();

    
}

开发者ID:Balu1991，项目名称:Wifly_Light，代码行数:82，代码来源:main.c

示例17: uart_int

static void uart_int() {
    int c = UARTCharGet(CONSOLE_UART);
    struct prompt_event pe = {.type = PROMPT_CHAR_EVENT, .data = (void *) c};
    osi_MsgQWrite(&s_v7_q, &pe, OSI_NO_WAIT);
    MAP_UARTIntClear(CONSOLE_UART, UART_INT_RX);
}

void sj_prompt_init_hal(struct v7 *v7) {
    (void) v7;
}

static void v7_task(void *arg) {
    struct v7 *v7 = s_v7;
    printf("\n\nSmart.JS for CC3200\n");

    osi_MsgQCreate(&s_v7_q, "V7", sizeof(struct prompt_event), 32 /* len */);
    osi_InterruptRegister(CONSOLE_UART_INT, uart_int, INT_PRIORITY_LVL_1);
    MAP_UARTIntEnable(CONSOLE_UART, UART_INT_RX);
    sl_Start(NULL, NULL, NULL);

    v7 = s_v7 = init_v7(&v7);
    sj_init_timers(v7);
    sj_init_v7_ext(v7);
    init_wifi(v7);
    if (init_fs(v7) != 0) {
        fprintf(stderr, "FS initialization failed.\n");
    }
    mongoose_init();
    sj_init_http(v7);
    init_i2cjs(v7);

    /* Common config infrastructure. Mongoose & v7 must be initialized. */
    init_device(v7);

    v7_val_t res;
    if (v7_exec_file(v7, "sys_init.js", &res) != V7_OK) {
        fprintf(stderr, "Error: ");
        v7_fprint(stderr, v7, res);
    }
    sj_prompt_init(v7);

    while (1) {
        struct prompt_event pe;
        mongoose_poll(MONGOOSE_POLL_LENGTH_MS);
        if (osi_MsgQRead(&s_v7_q, &pe, V7_POLL_LENGTH_MS) != OSI_OK) continue;
        switch (pe.type) {
        case PROMPT_CHAR_EVENT: {
            sj_prompt_process_char((char) ((int) pe.data));
            break;
        }
        case V7_INVOKE_EVENT: {
            struct v7_invoke_event_data *ied =
                (struct v7_invoke_event_data *) pe.data;
            _sj_invoke_cb(v7, ied->func, ied->this_obj, ied->args);
            v7_disown(v7, &ied->args);
            v7_disown(v7, &ied->this_obj);
            v7_disown(v7, &ied->func);
            free(ied);
            break;
        }
        }
    }
}

/* Int vector table, defined in startup_gcc.c */
extern void (*const g_pfnVectors[])(void);

void device_reboot(void) {
    sj_system_restart();
}

int main() {
    MAP_IntVTableBaseSet((unsigned long) &g_pfnVectors[0]);
    MAP_IntEnable(FAULT_SYSTICK);
    MAP_IntMasterEnable();
    PRCMCC3200MCUInit();

    cc3200_leds_init();

    /* Console UART init. */
    MAP_PRCMPeripheralClkEnable(CONSOLE_UART_PERIPH, PRCM_RUN_MODE_CLK);
    MAP_PinTypeUART(PIN_55, PIN_MODE_3); /* PIN_55 -> UART0_TX */
    MAP_PinTypeUART(PIN_57, PIN_MODE_3); /* PIN_57 -> UART0_RX */
    MAP_UARTConfigSetExpClk(
        CONSOLE_UART, MAP_PRCMPeripheralClockGet(CONSOLE_UART_PERIPH),
        CONSOLE_BAUD_RATE,
        (UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE | UART_CONFIG_PAR_NONE));
    MAP_UARTFIFODisable(CONSOLE_UART);

    setvbuf(stdout, NULL, _IONBF, 0);
    setvbuf(stderr, NULL, _IONBF, 0);

    VStartSimpleLinkSpawnTask(8);
    osi_TaskCreate(v7_task, (const signed char *) "v7", V7_STACK_SIZE + 256, NULL,
                   3, NULL);
    osi_TaskCreate(blinkenlights_task, (const signed char *) "blink", 256, NULL,
                   9, NULL);
    osi_start();

    return 0;
//.........这里部分代码省略.........

开发者ID:kirikiwi，项目名称:smart.js，代码行数:101，代码来源:main.c

示例18: main

int main(void) {
  MAP_IntVTableBaseSet((unsigned long) &int_vectors[0]);
  MAP_IntMasterEnable();
  PRCMCC3200MCUInit();

/* Console UART init. */
#ifndef NO_DEBUG
  MAP_PRCMPeripheralClkEnable(DEBUG_UART_PERIPH, PRCM_RUN_MODE_CLK);
#if MIOT_DEBUG_UART == 0
  MAP_PinTypeUART(PIN_55, PIN_MODE_3); /* UART0_TX */
  MAP_PinTypeUART(PIN_57, PIN_MODE_3); /* UART0_RX */
#else
  MAP_PinTypeUART(PIN_07, PIN_MODE_5); /* UART1_TX */
  MAP_PinTypeUART(PIN_08, PIN_MODE_5); /* UART1_RX */
#endif
  MAP_UARTConfigSetExpClk(
      DEBUG_UART_BASE, MAP_PRCMPeripheralClockGet(DEBUG_UART_PERIPH),
      MIOT_DEBUG_UART_BAUD_RATE,
      (UART_CONFIG_WLEN_8 | UART_CONFIG_STOP_ONE | UART_CONFIG_PAR_NONE));
  MAP_UARTFIFOLevelSet(DEBUG_UART_BASE, UART_FIFO_TX1_8, UART_FIFO_RX4_8);
  MAP_UARTFIFODisable(DEBUG_UART_BASE);
#endif

  dbg_puts("\r\n\n");

  if (sl_Start(NULL, NULL, NULL) < 0) abort();
  dbg_putc('S');

  int cidx = get_active_boot_cfg_idx();
  if (cidx < 0) abort();
  dbg_putc('0' + cidx);
  struct boot_cfg cfg;
  if (read_boot_cfg(cidx, &cfg) < 0) abort();

  dbg_puts(cfg.app_image_file);
  dbg_putc('@');
  print_addr(cfg.app_load_addr);

  /*
   * Zero memory before loading.
   * This should provide proper initialisation for BSS, wherever it is.
   */
  uint32_t *pstart = (uint32_t *) 0x20000000;
  uint32_t *pend = (&_text_start - 0x100 /* our stack */);
  for (uint32_t *p = pstart; p < pend; p++) *p = 0;

  if (load_image(cfg.app_image_file, (_u8 *) cfg.app_load_addr) != 0) {
    abort();
  }

  dbg_putc('.');

  sl_Stop(0);
  print_addr(*(((uint32_t *) cfg.app_load_addr) + 1));
  dbg_puts("\r\n\n");

  MAP_IntMasterDisable();
  MAP_IntVTableBaseSet(cfg.app_load_addr);

  run(cfg.app_load_addr); /* Does not return. */

  abort();

  return 0; /* not reached */
}

开发者ID:zikalino，项目名称:mongoose-iot，代码行数:65，代码来源:main.c

注：本文中的MAP_IntVTableBaseSet函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ MAP_PRCMPeripheralClkEnable函数代码示例发布时间：2022-05-30

C++ MAP_IntMasterEnable函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：18222|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9658|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8173|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8543|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8450|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9375|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8420|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7855|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8405|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7392|2022-11-06

客服电话

电子邮件

C++ MAP_IntVTableBaseSet函数代码示例

示例1: BoardInit

示例2: BoardInit

示例3: initBoard

示例4: SysPlatformConfig

示例5: bootmgr_board_init

示例6: main

示例7: bootmgr_board_init

示例8: BoardInit

示例9: BoardInit

示例10: main

示例11: BoardInit

示例12: BoardInit

示例13: bootmgr_board_init

示例14: main

示例15: bootmgr_board_init

示例16: main

示例17: uart_int

示例18: main

请发表评论

全部评论

上一篇：

下一篇：

librespeed/speedtest: Self-hosted Speedt

CVE-2022-34965

avehtari/BDA_m_demos: Bayesian Data Anal

四维彩超怎么看性别？四维看男孩女孩诀窍

个体户条例实施细则，2020 最新个体工商户

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053