本文整理汇总了C++中MS函数的典型用法代码示例。如果您正苦于以下问题：C++ MS函数的具体用法？C++ MS怎么用？C++ MS使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。
在下文中一共展示了MS函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。
示例1: ar9300GetSpectralParams
void
ar9300GetSpectralParams(struct ath_hal *ah, HAL_SPECTRAL_PARAM *ss)
{
u_int32_t val;
struct ath_hal_9300 *ahp = AH9300(ah);
HAL_POWER_MODE pwrmode = ahp->ah_powerMode;
if (AR_SREV_WASP(ah) && (pwrmode == HAL_PM_FULL_SLEEP)) {
ar9300SetPowerMode(ah, HAL_PM_AWAKE, AH_TRUE);
}
val = OS_REG_READ(ah, AR_PHY_SPECTRAL_SCAN);
ss->ss_fft_period = MS(val, AR_PHY_SPECTRAL_SCAN_FFT_PERIOD);
ss->ss_period = MS(val, AR_PHY_SPECTRAL_SCAN_PERIOD);
ss->ss_count = MS(val, AR_PHY_SPECTRAL_SCAN_COUNT);
ss->ss_short_report = MS(val, AR_PHY_SPECTRAL_SCAN_SHORT_REPEAT);
if (AR_SREV_WASP(ah) && (pwrmode == HAL_PM_FULL_SLEEP)) {
ar9300SetPowerMode(ah, HAL_PM_FULL_SLEEP, AH_TRUE);
}
}
开发者ID:jorneytu，项目名称:wlan，代码行数:22，代码来源:ar9300_spectral.c
示例2: ar5416EepromRead
/*
* Read 16 bits of data from offset into *data
*/
HAL_BOOL
ar5416EepromRead(struct ath_hal *ah, u_int off, u_int16_t *data)
{
(void)OS_REG_READ(ah, AR5416_EEPROM_OFFSET + (off << AR5416_EEPROM_S));
if (!ath_hal_wait(ah, AR_EEPROM_STATUS_DATA, AR_EEPROM_STATUS_DATA_BUSY
| AR_EEPROM_STATUS_DATA_PROT_ACCESS, 0, AH_WAIT_TIMEOUT))
{
return AH_FALSE;
}
*data = MS(OS_REG_READ(ah, AR_EEPROM_STATUS_DATA), AR_EEPROM_STATUS_DATA_VAL);
return AH_TRUE;
}
开发者ID:KHATEEBNSIT，项目名称:AP，代码行数:16，代码来源:ar5416_eeprom.c
示例3: ar9300GpioGet
/*
* Once configured for I/O - get input lines
*/
u_int32_t
ar9300GpioGet(struct ath_hal *ah, u_int32_t gpio)
{
u_int32_t gpio_in;
HALASSERT(gpio < AH_PRIVATE(ah)->ah_caps.halNumGpioPins);
if (gpio >= AH_PRIVATE(ah)->ah_caps.halNumGpioPins) {
return 0xffffffff;
}
gpio_in = OS_REG_READ(ah, AR_HOSTIF_REG(ah, AR_GPIO_IN));
return (MS(gpio_in, AR_GPIO_IN_VAL) & AR_GPIO_BIT(gpio)) != 0;
}
开发者ID:KHATEEBNSIT，项目名称:AP，代码行数:16，代码来源:ar9300_gpio.c
示例4: secondtask
/* This function is executed by the second task that is set up
* in the function firsttask() by a call to nosTaskCreate()
*/
void secondtask(void *arg)
{
char *name = (char*) arg;
for(;;)
{
/* print string: "Task 2" */
nosPrintf1("%s\n", name);
/* sleep (=do nothing) for two seconds */
nosTaskSleep(MS(2000));
}
}
开发者ID:Sundarapandian，项目名称:avr_projects，代码行数:16，代码来源:ex_task4.c
示例5: ar5416GpioSetIntr
/*
* Set the GPIO Interrupt
*/
void
ar5416GpioSetIntr(struct ath_hal *ah, u_int gpio, uint32_t ilevel)
{
uint32_t val;
HALASSERT(gpio < AR_NUM_GPIO);
/* XXX bounds check gpio */
val = MS(OS_REG_READ(ah, AR_GPIO_INTR_OUT), AR_GPIO_INTR_CTRL);
if (ilevel) /* 0 == interrupt on pin high */
val &= ~AR_GPIO_BIT(gpio);
else /* 1 == interrupt on pin low */
val |= AR_GPIO_BIT(gpio);
OS_REG_RMW_FIELD(ah, AR_GPIO_INTR_OUT, AR_GPIO_INTR_CTRL, val);
/* Change the interrupt mask. */
val = MS(OS_REG_READ(ah, AR_INTR_ASYNC_ENABLE), AR_INTR_GPIO);
val |= AR_GPIO_BIT(gpio);
OS_REG_RMW_FIELD(ah, AR_INTR_ASYNC_ENABLE, AR_INTR_GPIO, val);
val = MS(OS_REG_READ(ah, AR_INTR_ASYNC_MASK), AR_INTR_GPIO);
val |= AR_GPIO_BIT(gpio);
OS_REG_RMW_FIELD(ah, AR_INTR_ASYNC_MASK, AR_INTR_GPIO, val);
}
开发者ID:se7oluti0n，项目名称:madwifi，代码行数:26，代码来源:ar5416_gpio.c
示例6: tcpClientThread
void tcpClientThread(void* arg)
{
int sock = (long)arg;
int i;
nosPrintf("in tcp client\n");
for (i = 0; i < 5; i++) {
write(sock, "Hello!\n", 7);
posTaskSleep(MS(1000));
}
close(sock);
}
开发者ID:AriZuu，项目名称:wiced-test，代码行数:14，代码来源:sock_server.c
示例7: ar7010GpioGet
/*
* Once configured for I/O - get input lines
*/
u_int32_t
ar7010GpioGet(struct ath_hal *ah, u_int32_t gpio)
{
HALASSERT(gpio < AH_PRIVATE(ah)->ah_caps.hal_num_gpio_pins);
if (gpio >= AH_PRIVATE(ah)->ah_caps.hal_num_gpio_pins) {
return 0xffffffff;
}
/* Read output value for all gpio's, shift it left, and verify whether a
* specific gpio bit is set.
*/
return (MS(OS_REG_READ(ah, AR7010_GPIO_IN), AR7010_GPIO_IN_VAL) & AR_GPIO_BIT(gpio)) != 0;
}
开发者ID:KHATEEBNSIT，项目名称:AP，代码行数:17，代码来源:ar5416_gpio.c
示例8: ar9280_olpc_init
void
ar9280_olpc_init(struct athn_softc *sc)
{
uint32_t reg;
int i;
/* Save original Tx gain values. */
for (i = 0; i < AR9280_TX_GAIN_TABLE_SIZE; i++) {
reg = AR_READ(sc, AR_PHY_TX_GAIN_TBL(i));
sc->tx_gain_tbl[i] = MS(reg, AR_PHY_TX_GAIN);
}
/* Initial Tx gain temperature compensation. */
sc->tcomp = 0;
}
开发者ID:alenichev，项目名称:openbsd-kernel，代码行数:14，代码来源:ar9280.c
示例9: task2
/* This function is executed by the second task that is set up
* in the function firsttask() by a call to nosTaskCreate()
*/
void task2(void *arg)
{
/* avoid compiler warning */
(void) arg;
for(;;)
{
/* call function */
incrementCounter(2);
/* do something here and waste some time */
posTaskSleep(MS(300));
}
}
开发者ID:AriZuu，项目名称:picoos，代码行数:17，代码来源:ex_mutx1.c
示例10: sizeof
/* Applies for first msdu in chain, before altering it. */
static struct ieee80211_hdr *ath10k_htt_rx_skb_get_hdr(struct sk_buff *skb)
{
struct htt_rx_desc *rxd;
enum rx_msdu_decap_format fmt;
rxd = (void *)skb->data - sizeof(*rxd);
fmt = MS(__le32_to_cpu(rxd->msdu_start.info1),
RX_MSDU_START_INFO1_DECAP_FORMAT);
if (fmt == RX_MSDU_DECAP_RAW)
return (void *)skb->data;
else
return (void *)skb->data - RX_HTT_HDR_STATUS_LEN;
}
开发者ID:AkyZero，项目名称:wrapfs-latest，代码行数:15，代码来源:htt_rx.c
示例11: ar2133GetNoiseFloor
static void
ar2133GetNoiseFloor(struct ath_hal *ah, int16_t nfarray[])
{
struct ath_hal_5416 *ahp = AH5416(ah);
int16_t nf;
switch (ahp->ah_rx_chainmask) {
case 0x7:
nf = MS(OS_REG_READ(ah, AR_PHY_CH2_CCA), AR_PHY_CH2_MINCCA_PWR);
if (nf & 0x100)
nf = 0 - ((nf ^ 0x1ff) + 1);
HALDEBUG(ah, HAL_DEBUG_NFCAL,
"NF calibrated [ctl] [chain 2] is %d\n", nf);
nfarray[4] = nf;
nf = MS(OS_REG_READ(ah, AR_PHY_CH2_EXT_CCA), AR_PHY_CH2_EXT_MINCCA_PWR);
if (nf & 0x100)
nf = 0 - ((nf ^ 0x1ff) + 1);
HALDEBUG(ah, HAL_DEBUG_NFCAL,
"NF calibrated [ext] [chain 2] is %d\n", nf);
nfarray[5] = nf;
/* fall thru... */
case 0x3:
case 0x5:
nf = MS(OS_REG_READ(ah, AR_PHY_CH1_CCA), AR_PHY_CH1_MINCCA_PWR);
if (nf & 0x100)
nf = 0 - ((nf ^ 0x1ff) + 1);
HALDEBUG(ah, HAL_DEBUG_NFCAL,
"NF calibrated [ctl] [chain 1] is %d\n", nf);
nfarray[2] = nf;
nf = MS(OS_REG_READ(ah, AR_PHY_CH1_EXT_CCA), AR_PHY_CH1_EXT_MINCCA_PWR);
if (nf & 0x100)
nf = 0 - ((nf ^ 0x1ff) + 1);
HALDEBUG(ah, HAL_DEBUG_NFCAL,
"NF calibrated [ext] [chain 1] is %d\n", nf);
nfarray[3] = nf;
/* fall thru... */
case 0x1:
nf = MS(OS_REG_READ(ah, AR_PHY_CCA), AR_PHY_MINCCA_PWR);
if (nf & 0x100)
nf = 0 - ((nf ^ 0x1ff) + 1);
HALDEBUG(ah, HAL_DEBUG_NFCAL,
"NF calibrated [ctl] [chain 0] is %d\n", nf);
nfarray[0] = nf;
nf = MS(OS_REG_READ(ah, AR_PHY_EXT_CCA), AR_PHY_EXT_MINCCA_PWR);
if (nf & 0x100)
nf = 0 - ((nf ^ 0x1ff) + 1);
HALDEBUG(ah, HAL_DEBUG_NFCAL,
"NF calibrated [ext] [chain 0] is %d\n", nf);
nfarray[1] = nf;
break;
}
}
开发者ID:AhmadTux，项目名称:DragonFlyBSD，代码行数:57，代码来源:ar2133.c
示例12: ar5416GpioSet
/*
* Once configured for I/O - set output lines
*/
HAL_BOOL
ar5416GpioSet(struct ath_hal *ah, uint32_t gpio, uint32_t val)
{
uint32_t reg;
HALASSERT(gpio < AR_NUM_GPIO);
reg = MS(OS_REG_READ(ah, AR_GPIO_INTR_OUT), AR_GPIO_OUT_VAL);
if (val & 1)
reg |= AR_GPIO_BIT(gpio);
else
reg &= ~AR_GPIO_BIT(gpio);
OS_REG_RMW_FIELD(ah, AR_GPIO_INTR_OUT, AR_GPIO_OUT_VAL, reg);
return AH_TRUE;
}
开发者ID:se7oluti0n，项目名称:madwifi，代码行数:18，代码来源:ar5416_gpio.c
示例13: r12a_rx_radiotap_flags
uint8_t
r12a_rx_radiotap_flags(const void *buf)
{
const struct r92c_rx_stat *stat = buf;
uint8_t flags, rate;
if (!(stat->rxdw4 & htole32(R12A_RXDW4_SPLCP)))
return (0);
rate = MS(le32toh(stat->rxdw3), R92C_RXDW3_RATE);
if (RTWN_RATE_IS_CCK(rate))
flags = IEEE80211_RADIOTAP_F_SHORTPRE;
else
flags = IEEE80211_RADIOTAP_F_SHORTGI;
return (flags);
}
开发者ID:jaredmcneill，项目名称:freebsd，代码行数:15，代码来源:r12a_rx.c
示例14: sendStatus
void Status::tick()
{
// Si on a de la place sur le buffer de sortie, alors on accepte
if (Serial.availableForWrite() < sizeof(struct Payload)) {
// Il faut attendre pendant au moins ce temps
this->nextTick = UTime::now() + (sizeof(struct Payload) + 2) * CHAR_XMIT_DELAY;
return;
}
sendStatus();
if (motor.isMoving() || filterWheelMotor.isMoving()) {
this->nextTick += MS(250);
} else {
this->nextTick += LongDuration::seconds(10);
}
}
开发者ID:pludov，项目名称:ArdFocuser，代码行数:15，代码来源:Status.cpp
示例15: rx_task
void rx_task(void * ignore)
{
int cnt = 0;
while (1) {
if (uart_gets(buf) <= 0)
continue;
PORTB ^= _BV(PB0);
if (!strncmp(buf, "+BTINQ: ", 8)) {
char * x = strchr(&buf[8], ',');
if (x == NULL) continue;
*(x+1) = 0;
//strcpy(ptr[cnt], &buf[8]);
uart_puts("AT+BTSDP=");
uart_puts(&buf[8]);
uart_puts("2\r");
posTaskSleep(MS(500));
PORTB ^= _BV(PB0);
posTaskSleep(MS(500));
PORTB ^= _BV(PB0);
posTaskSleep(MS(500));
PORTB ^= _BV(PB0);
}
}
}
开发者ID:Sundarapandian，项目名称:avr_projects，代码行数:24，代码来源:bttest.c
示例16: secondtask
/* This function is executed by the second task that is set up
* in the function firsttask() by a call to nosTaskCreate()
*/
void secondtask(void *arg)
{
char *name = (char*) arg;
for(;;)
{
/* print string: "Task 2" */
posTaskSchedLock();
printf("%s\n", name);
posTaskSchedUnlock();
/* sleep (=do nothing) for two seconds */
posTaskSleep(MS(2000));
}
}
开发者ID:AriZuu，项目名称:picoos，代码行数:18，代码来源:ex_task1.c
示例17: ar9300GetExtChanNF
int16_t ar9300GetExtChanNF(struct ath_hal *ah)
{
int16_t nf;
struct ath_hal_private *ahpriv = AH_PRIVATE(ah);
if ((OS_REG_READ(ah, AR_PHY_AGC_CONTROL) & AR_PHY_AGC_CONTROL_NF) == 0) {
/* Noise floor calibration value is ready */
nf = MS(OS_REG_READ(ah, AR_PHY_EXT_CCA), AR_PHY_EXT_MINCCA_PWR);
} else {
/* NF calibration is not done, return nominal value */
nf = ahpriv->nfp->nominal;
}
if (nf & 0x100)
nf = (0 - ((nf ^ 0x1ff) + 1));
return nf;
}
开发者ID:jorneytu，项目名称:wlan，代码行数:16，代码来源:ar9300_spectral.c
示例18: ar5212_decode_rxstatus
static void
ar5212_decode_rxstatus(struct if_ath_alq_payload *a)
{
struct ar5212_desc rxs;
/* XXX assumes rxs is smaller than PAYLOAD_LEN! */
memcpy(&rxs, &a->payload, sizeof(struct ar5212_desc));
printf("[%u] [%llu] RXSTATUS\n",
(unsigned int) be32toh(a->hdr.tstamp),
(unsigned long long) be64toh(a->hdr.threadid));
printf(" link=0x%08x, data=0x%08x, ctl0=0x%08x, ctl2=0x%08x\n",
rxs.ds_link,
rxs.ds_data,
rxs.ds_ctl0,
rxs.ds_ctl1);
/* ds_rxstatus0 */
printf(" DataLen=%d, ArMore=%d, DecompCrcError=%d, RcvRate=0x%02x\n",
rxs.ds_rxstatus0 & AR_DataLen,
MF(rxs.ds_rxstatus0, AR_More),
MF(rxs.ds_rxstatus0, AR_DecompCRCErr),
MS(rxs.ds_rxstatus0, AR_RcvRate));
printf(" RSSI=%d, RcvAntenna=0x%x\n",
MS(rxs.ds_rxstatus0, AR_RcvSigStrength),
MS(rxs.ds_rxstatus0, AR_RcvAntenna));
/* ds_rxstatus1 */
printf(" RxDone=%d, RxFrameOk=%d, CrcErr=%d, DecryptCrcErr=%d\n",
MF(rxs.ds_rxstatus1, AR_Done),
MF(rxs.ds_rxstatus1, AR_FrmRcvOK),
MF(rxs.ds_rxstatus1, AR_CRCErr),
MF(rxs.ds_rxstatus1, AR_DecryptCRCErr));
printf(" PhyErr=%d, MichaelErr=%d, KeyIdxValid=%d\n",
MF(rxs.ds_rxstatus1, AR_PHYErr),
MF(rxs.ds_rxstatus1, AR_MichaelErr),
MF(rxs.ds_rxstatus1, AR_KeyIdxValid));
/* If PHY error, print that out. Otherwise, the key index */
if (MF(rxs.ds_rxstatus1, AR_PHYErr))
printf(" PhyErrCode=0x%02x\n",
MS(rxs.ds_rxstatus1, AR_PHYErrCode));
else
printf(" KeyIdx=0x%02x\n",
MS(rxs.ds_rxstatus1, AR_KeyIdx));
printf(" KeyMiss=%d\n",
MF(rxs.ds_rxstatus1, AR_KeyCacheMiss));
printf(" Timetamp: 0x%05x\n",
MS(rxs.ds_rxstatus1, AR_RcvTimestamp));
printf("\n ------\n");
}
开发者ID:vkhromov，项目名称:freebsd，代码行数:55，代码来源:ar5212_ds.c
示例19: r12a_tx_radiotap_flags
uint8_t
r12a_tx_radiotap_flags(const void *buf)
{
const struct r12a_tx_desc *txd = buf;
uint8_t flags, rate;
if (!(txd->txdw5 & htole32(R12A_TXDW5_DATA_SHORT)))
return (0);
rate = MS(le32toh(txd->txdw4), R12A_TXDW4_DATARATE);
if (RTWN_RATE_IS_CCK(rate))
flags = IEEE80211_RADIOTAP_F_SHORTPRE;
else
flags = IEEE80211_RADIOTAP_F_SHORTGI;
return (flags);
}
开发者ID:jaredmcneill，项目名称:freebsd，代码行数:16，代码来源:r12a_tx.c
示例20: r12a_c_cut_rf_read
uint32_t
r12a_c_cut_rf_read(struct rtwn_softc *sc, int chain, uint8_t addr)
{
uint32_t pi_mode, val;
val = rtwn_bb_read(sc, R12A_HSSI_PARAM1(chain));
pi_mode = (val & R12A_HSSI_PARAM1_PI) ? 1 : 0;
rtwn_bb_setbits(sc, R12A_HSSI_PARAM2,
R12A_HSSI_PARAM2_READ_ADDR_MASK, addr);
rtwn_delay(sc, 20);
val = rtwn_bb_read(sc, pi_mode ? R12A_HSPI_READBACK(chain) :
R12A_LSSI_READBACK(chain));
return (MS(val, R92C_LSSI_READBACK_DATA));
}
开发者ID:2trill2spill，项目名称:freebsd，代码行数:17，代码来源:r12a_rf.c
注：本文中的MS函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。 |
客服电话
APP下载
官方微信
请发表评论