C++ MUX_PAD_CTRL函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中MUX_PAD_CTRL函数的典型用法代码示例。如果您正苦于以下问题：C++ MUX_PAD_CTRL函数的具体用法？C++ MUX_PAD_CTRL怎么用？C++ MUX_PAD_CTRL使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了MUX_PAD_CTRL函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: setup_epdc

static void setup_epdc(void)
{
	/*** epdc Maxim PMIC settings ***/

	/* EPDC_PWRSTAT - GPIO2[31] for PWR_GOOD status */
	imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));

	/* EPDC_VCOM0 - GPIO4[14] for VCOM control */
	imx_iomux_v3_setup_pad(MX7D_PAD_I2C4_SCL__GPIO4_IO14 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));

	/* EPDC_PWRWAKEUP - GPIO4[23] for EPD PMIC WAKEUP */
	imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_SDCE3__GPIO2_IO23 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));

	/* EPDC_PWRCTRL0 - GPIO4[20] for EPD PWR CTL0 */
	imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));

	/* Set pixel clock rates for EPDC in clock.c */

	panel_info.epdc_data.wv_modes.mode_init = 0;
	panel_info.epdc_data.wv_modes.mode_du = 1;
	panel_info.epdc_data.wv_modes.mode_gc4 = 3;
	panel_info.epdc_data.wv_modes.mode_gc8 = 2;
	panel_info.epdc_data.wv_modes.mode_gc16 = 2;
	panel_info.epdc_data.wv_modes.mode_gc32 = 2;

	panel_info.epdc_data.epdc_timings = panel_timings;

	setup_epdc_power();
}

开发者ID:Toradex-Apalis-TK1-AndroidTV，项目名称:android_3rdparty_uboot，代码行数:33，代码来源:mx7dsabresd.c

示例2: setup_epdc_power

static void setup_epdc_power(void)
{
	/* Setup epdc voltage */

	/* EIM_A17 - GPIO2[21] for PWR_GOOD status */
	imx_iomux_v3_setup_pad(MX6_PAD_EIM_A17__GPIO2_IO21 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));
	/* Set as input */
	gpio_direction_input(IMX_GPIO_NR(2, 21));

	/* EIM_D17 - GPIO3[17] for VCOM control */
	imx_iomux_v3_setup_pad(MX6_PAD_EIM_D17__GPIO3_IO17 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));

	/* Set as output */
	gpio_direction_output(IMX_GPIO_NR(3, 17), 1);

	/* EIM_D20 - GPIO3[20] for EPD PMIC WAKEUP */
	imx_iomux_v3_setup_pad(MX6_PAD_EIM_D20__GPIO3_IO20 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));
	/* Set as output */
	gpio_direction_output(IMX_GPIO_NR(3, 20), 1);

	/* EIM_A18 - GPIO2[20] for EPD PWR CTL0 */
	imx_iomux_v3_setup_pad(MX6_PAD_EIM_A18__GPIO2_IO20 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));
	/* Set as output */
	gpio_direction_output(IMX_GPIO_NR(2, 20), 1);
}

开发者ID:heyoufei2，项目名称:yocto_uboot2015，代码行数:29，代码来源:mx6sabresd.c

示例3: setup_epdc_power

static void setup_epdc_power(void)
{
	/* IOMUX_GPR1: bit30: Disable On-chip RAM EPDC Function */
	struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
		= (struct iomuxc_gpr_base_regs *) IOMUXC_GPR_BASE_ADDR;

	clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
		IOMUXC_GPR_GPR1_GPR_ENABLE_OCRAM_EPDC_MASK, 0);

	/* Setup epdc voltage */

	/* EPDC_PWRSTAT - GPIO2[31] for PWR_GOOD status */
	imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));
	gpio_direction_input(IMX_GPIO_NR(2, 31));

	/* EPDC_VCOM0 - GPIO4[14] for VCOM control */
	imx_iomux_v3_setup_pad(MX7D_PAD_I2C4_SCL__GPIO4_IO14 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));

	/* Set as output */
	gpio_direction_output(IMX_GPIO_NR(4, 14), 1);

	/* EPDC_PWRWAKEUP - GPIO2[23] for EPD PMIC WAKEUP */
	imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_SDCE3__GPIO2_IO23 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));
	/* Set as output */
	gpio_direction_output(IMX_GPIO_NR(2, 23), 1);

	/* EPDC_PWRCTRL0 - GPIO2[30] for EPD PWR CTL0 */
	imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));
	/* Set as output */
	gpio_direction_output(IMX_GPIO_NR(2, 30), 1);
}

开发者ID:Toradex-Apalis-TK1-AndroidTV，项目名称:android_3rdparty_uboot，代码行数:35，代码来源:mx7dsabresd.c

示例4: setup_epdc_power

static void setup_epdc_power(void)
{
	/* Setup epdc voltage */

	/* EPDC_PWRSTAT - GPIO2[13] for PWR_GOOD status */
	imx_iomux_v3_setup_pad(MX6_PAD_EPDC_PWRSTAT__GPIO_2_13 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));
	gpio_direction_input(IMX_GPIO_NR(2, 13));

	/* EPDC_VCOM0 - GPIO2[3] for VCOM control */
	imx_iomux_v3_setup_pad(MX6_PAD_EPDC_VCOM0__GPIO_2_3 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));

	/* Set as output */
	gpio_direction_output(IMX_GPIO_NR(2, 3), 1);

	/* EPDC_PWRWAKEUP - GPIO2[14] for EPD PMIC WAKEUP */
	imx_iomux_v3_setup_pad(MX6_PAD_EPDC_PWRWAKEUP__GPIO_2_14 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));
	/* Set as output */
	gpio_direction_output(IMX_GPIO_NR(2, 14), 1);

	/* EPDC_PWRCTRL0 - GPIO2[7] for EPD PWR CTL0 */
	imx_iomux_v3_setup_pad(MX6_PAD_EPDC_PWRCTRL0__GPIO_2_7 |
				MUX_PAD_CTRL(EPDC_PAD_CTRL));
	/* Set as output */
	gpio_direction_output(IMX_GPIO_NR(2, 7), 1);
}

开发者ID:geneyeung，项目名称:u-boot-3.10.17，代码行数:28，代码来源:mx6slevk.c

示例5: setup_iomux_uart

static void setup_iomux_uart(void)
{
	static iomux_v3_cfg_t const uart1_pads[] = {
		MX6_PAD_UART1_TXD__UART1_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
		MX6_PAD_UART1_RXD__UART1_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
	};

	imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}

开发者ID:0xFelix，项目名称:u-boot-edminiv2，代码行数:9，代码来源:warp.c

示例6: cm_fx6_setup_usb_host

static int cm_fx6_setup_usb_host(void)
{
	int err;

	err = gpio_request(CM_FX6_USB_HUB_RST, "usb hub rst");
	if (err)
		return err;

	SETUP_IOMUX_PAD(PAD_GPIO_0__USB_H1_PWR | MUX_PAD_CTRL(NO_PAD_CTRL));
	SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL));

	return 0;
}

开发者ID:analogdevicesinc，项目名称:u-boot-xlnx，代码行数:13，代码来源:cm_fx6.c

示例7: mx50_suspend_exit

static void mx50_suspend_exit()
{
	iomux_v3_cfg_t iomux_setting =
			(MX50_PAD_ECSPI2_SCLK__GPIO_4_16 &
			~MUX_PAD_CTRL_MASK) | MUX_PAD_CTRL(0x84);

	/* Power Up the band-gap and set the SELFBIAS bit. */
	__raw_writel(MXC_ANADIG_REF_PWD,
			apll_base + MXC_ANADIG_MISC_CLR);
	udelay(100);
	__raw_writel(MXC_ANADIG_REF_SELFBIAS_OFF,
			apll_base + MXC_ANADIG_MISC_SET);

	//if (board_is_mx50_rd3()) {
		/* Enable the Pull/keeper */
		mxc_iomux_v3_setup_pad(iomux_setting);
		gpio_request(DCDC_EN, "dcdc-en");
		gpio_direction_output(DCDC_EN, 1);
	//}

	mxc_iomux_v3_setup_multiple_pads(suspend_exit_pads,
			ARRAY_SIZE(suspend_exit_pads));

    nimbus_gpio_iomux_init();

}

开发者ID:SanDisk-Open-Source，项目名称:wireless-media-drive，代码行数:26，代码来源:mx50_rdp_nimbus.c

示例8: nimbus_gpio_iomux_init

static void nimbus_gpio_iomux_init()
{
	iomux_v3_cfg_t iomux_setting;

	iomux_setting = (MX50_PAD_ECSPI2_SCLK__GPIO_4_16 & \
				~MUX_PAD_CTRL_MASK) | \
				MUX_PAD_CTRL(PAD_CTL_PKE | PAD_CTL_DSE_HIGH);

	/* Enable the Pull/keeper */
	mxc_iomux_v3_setup_pad(iomux_setting);

    nimbus_led_ctrl(LEDID_WLAN,0,0);
    nimbus_led_ctrl(LEDID_WIFI,0,0);
    nimbus_led_ctrl(LEDID_CHARGER_RED,0,0);
    nimbus_led_ctrl(LEDID_CHARGER_GREEN,0,0);
    
    #if 0
    if( gpio_get_value(SD1_CHANGE_FOUND)==0)
    {
        printk("Found SD changed during suspending.\n");
        
    }

    gpio_direction_output(SD1_CHANGE_CLEAR,1); 
    mdelay(1);
    gpio_direction_output(SD1_CHANGE_CLEAR,0); 
    #endif
}

开发者ID:SanDisk-Open-Source，项目名称:wireless-media-drive，代码行数:28，代码来源:mx50_rdp_nimbus.c

示例9: cm_fx6_init_usb_otg

static int cm_fx6_init_usb_otg(void)
{
	int ret;
	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;

	ret = gpio_request(SB_FX6_USB_OTG_PWR, "usb-pwr");
	if (ret) {
		printf("USB OTG pwr gpio request failed: %d\n", ret);
		return ret;
	}

	SETUP_IOMUX_PAD(PAD_EIM_D22__GPIO3_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL));
	SETUP_IOMUX_PAD(PAD_ENET_RX_ER__USB_OTG_ID |
						MUX_PAD_CTRL(WEAK_PULLDOWN));
	clrbits_le32(&iomux->gpr[1], IOMUXC_GPR1_OTG_ID_MASK);
	/* disable ext. charger detect, or it'll affect signal quality at dp. */
	return gpio_direction_output(SB_FX6_USB_OTG_PWR, 0);
}

开发者ID:RobertCNelson，项目名称:debian-u-boot，代码行数:18，代码来源:cm_fx6.c

示例10: board_eth_init

int board_eth_init(bd_t *bis)
{
	struct phy_device *phydev;
	struct mii_dev *bus;
	unsigned short id1, id2;
	int ret;

	iomux_v3_cfg_t enet_reset = MX6_PAD_EIM_D23__GPIO3_IO23 |
				    MUX_PAD_CTRL(NO_PAD_CTRL);

	/* check whether KSZ9031 or AR8035 has to be configured */
	imx_iomux_v3_setup_multiple_pads(enet_pads_ar8035,
					 ARRAY_SIZE(enet_pads_ar8035));
	imx_iomux_v3_setup_pad(enet_reset);

	/* phy reset */
	gpio_direction_output(IMX_GPIO_NR(3, 23), 0);
	udelay(2000);
	gpio_set_value(IMX_GPIO_NR(3, 23), 1);
	udelay(500);

	bus = fec_get_miibus(IMX_FEC_BASE, -1);
	if (!bus)
		return -EINVAL;
	phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII);
	if (!phydev) {
		printf("Error: phy device not found.\n");
		ret = -ENODEV;
		goto free_bus;
	}

	/* get the PHY id */
	id1 = phy_read(phydev, MDIO_DEVAD_NONE, 2);
	id2 = phy_read(phydev, MDIO_DEVAD_NONE, 3);

	if ((id1 == 0x22) && ((id2 & 0xFFF0) == 0x1620)) {
		/* re-configure for Micrel KSZ9031 */
		printf("configure Micrel KSZ9031 Ethernet Phy at address %d\n",
		       phydev->addr);

		/* phy reset: gpio3-23 */
		gpio_set_value(IMX_GPIO_NR(3, 23), 0);
		gpio_set_value(IMX_GPIO_NR(6, 30), (phydev->addr >> 2));
		gpio_set_value(IMX_GPIO_NR(6, 25), 1);
		gpio_set_value(IMX_GPIO_NR(6, 27), 1);
		gpio_set_value(IMX_GPIO_NR(6, 28), 1);
		gpio_set_value(IMX_GPIO_NR(6, 29), 1);
		imx_iomux_v3_setup_multiple_pads(enet_pads_ksz9031,
						 ARRAY_SIZE(enet_pads_ksz9031));
		gpio_set_value(IMX_GPIO_NR(6, 24), 1);
		udelay(500);
		gpio_set_value(IMX_GPIO_NR(3, 23), 1);
		imx_iomux_v3_setup_multiple_pads(enet_pads_final_ksz9031,
						 ARRAY_SIZE(enet_pads_final_ksz9031));
	} else if ((id1 == 0x004d) && (id2 == 0xd072)) {

开发者ID:KaijiHakaroku，项目名称:u-boot，代码行数:55，代码来源:cgtqmx6eval.c

示例11: mx51_babbage_init

/*
 * Board specific initialization.
 */
static void __init mx51_babbage_init(void)
{
	iomux_v3_cfg_t usbh1stp = MX51_PAD_USBH1_STP__USBH1_STP;
	iomux_v3_cfg_t power_key = _MX51_PAD_EIM_A27__GPIO2_21 |
		MUX_PAD_CTRL(PAD_CTL_SRE_FAST | PAD_CTL_DSE_HIGH | PAD_CTL_PUS_100K_UP);

	imx51_soc_init();

#if defined(CONFIG_CPU_FREQ_IMX)
	get_cpu_op = mx51_get_cpu_op;
#endif
	mxc_iomux_v3_setup_multiple_pads(mx51babbage_pads,
					ARRAY_SIZE(mx51babbage_pads));

	imx51_add_imx_uart(0, &uart_pdata);
	imx51_add_imx_uart(1, NULL);
	imx51_add_imx_uart(2, &uart_pdata);

	babbage_fec_reset();
	imx51_add_fec(NULL);

	/* Set the PAD settings for the pwr key. */
	mxc_iomux_v3_setup_pad(power_key);
	imx_add_gpio_keys(&imx_button_data);

	imx51_add_imx_i2c(0, &babbage_i2c_data);
	imx51_add_imx_i2c(1, &babbage_i2c_data);
	mxc_register_device(&mxc_hsi2c_device, &babbage_hsi2c_data);

	if (otg_mode_host)
		mxc_register_device(&mxc_usbdr_host_device, &dr_utmi_config);
	else {
		initialize_otg_port(NULL);
		mxc_register_device(&mxc_usbdr_udc_device, &usb_pdata);
	}

	gpio_usbh1_active();
	mxc_register_device(&mxc_usbh1_device, &usbh1_config);
	/* setback USBH1_STP to be function */
	mxc_iomux_v3_setup_pad(usbh1stp);
	babbage_usbhub_reset();

	imx51_add_sdhci_esdhc_imx(0, &mx51_babbage_sd1_data);
	imx51_add_sdhci_esdhc_imx(1, &mx51_babbage_sd2_data);

	spi_register_board_info(mx51_babbage_spi_board_info,
		ARRAY_SIZE(mx51_babbage_spi_board_info));
	imx51_add_ecspi(0, &mx51_babbage_spi_pdata);
	imx51_add_imx2_wdt(0, NULL);
}

开发者ID:CSCLOG，项目名称:beaglebone，代码行数:53，代码来源:board-mx51_babbage.c

示例12: cm_fx6_usb_hub_reset

static int cm_fx6_usb_hub_reset(void)
{
	int err;

	err = gpio_request(CM_FX6_USB_HUB_RST, "usb hub rst");
	if (err) {
		printf("USB hub rst gpio request failed: %d\n", err);
		return -1;
	}

	SETUP_IOMUX_PAD(PAD_SD3_RST__GPIO7_IO08 | MUX_PAD_CTRL(NO_PAD_CTRL));
	gpio_direction_output(CM_FX6_USB_HUB_RST, 0);
	udelay(10);
	gpio_direction_output(CM_FX6_USB_HUB_RST, 1);
	mdelay(1);

	return 0;
}

开发者ID:RobertCNelson，项目名称:debian-u-boot，代码行数:18，代码来源:cm_fx6.c

示例13: board_init

int board_init(void)
{
	/* address of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

	imx_iomux_v3_setup_pad(MX6_PAD_NANDF_D4__GPIO2_IO04 |
			       MUX_PAD_CTRL(NO_PAD_CTRL));

	gpio_direction_output(IMX_GPIO_NR(2, 4), 0);

	/* Set Low */
	gpio_set_value(IMX_GPIO_NR(2, 4), 0);
	udelay(1000);

	/* Set High */
	gpio_set_value(IMX_GPIO_NR(2, 4), 1);

	return 0;
}

开发者ID:RowanLiu，项目名称:ported_uboot，代码行数:19，代码来源:mx6quq7.c

示例14: board_ehci_hcd_init

int board_ehci_hcd_init(int port)
{
	u32 *usbnc_usb_uh1_ctrl = (u32 *)(MX6_USBNC_BASEADDR + 4);

	switch (port) {
	case 0:
		return cm_fx6_init_usb_otg();
	case 1:
		SETUP_IOMUX_PAD(PAD_GPIO_0__USB_H1_PWR |
				MUX_PAD_CTRL(NO_PAD_CTRL));

		/* Set PWR polarity to match power switch's enable polarity */
		setbits_le32(usbnc_usb_uh1_ctrl, USBNC_USB_H1_PWR_POL);
		return cm_fx6_usb_hub_reset();
	default:
		break;
	}

	return 0;
}

开发者ID:RobertCNelson，项目名称:debian-u-boot，代码行数:20，代码来源:cm_fx6.c

示例15: mx50_suspend_enter

static void mx50_suspend_enter()
{
	iomux_v3_cfg_t *p = suspend_enter_pads;
	int i;
	iomux_v3_cfg_t iomux_setting =
			(MX50_PAD_ECSPI2_SCLK__GPIO_4_16 &
			~MUX_PAD_CTRL_MASK) | MUX_PAD_CTRL(0x84);

	/* Clear the SELF_BIAS bit and power down
	 * the band-gap.
	 */
	__raw_writel(MXC_ANADIG_REF_SELFBIAS_OFF,
			apll_base + MXC_ANADIG_MISC_CLR);
	__raw_writel(MXC_ANADIG_REF_PWD,
			apll_base + MXC_ANADIG_MISC_SET);

	//if (board_is_mx50_rd3()) {
		/* Enable the Pull/keeper */
		mxc_iomux_v3_setup_pad(iomux_setting);
		gpio_request(DCDC_EN, "dcdc-en");
		gpio_direction_output(DCDC_EN, 0);
	//}

	/* Set PADCTRL to 0 for all IOMUX. */
	for (i = 0; i < ARRAY_SIZE(suspend_enter_pads); i++) {
		suspend_exit_pads[i] = *p;
		*p &= ~MUX_PAD_CTRL_MASK;
		p++;
	}
   
	mxc_iomux_v3_get_multiple_pads(suspend_exit_pads,
			ARRAY_SIZE(suspend_exit_pads));
	mxc_iomux_v3_setup_multiple_pads(suspend_enter_pads,
			ARRAY_SIZE(suspend_enter_pads));

    nimbus_gpio_iomux_deinit();

    //system_status=2;

}

开发者ID:SanDisk-Open-Source，项目名称:wireless-media-drive，代码行数:40，代码来源:mx50_rdp_nimbus.c

示例16: nimbus_gpio_iomux_deinit

static void nimbus_gpio_iomux_deinit()
{
	iomux_v3_cfg_t iomux_setting;

	iomux_setting = (MX50_PAD_ECSPI2_SCLK__GPIO_4_16 & \
					~MUX_PAD_CTRL_MASK) | MUX_PAD_CTRL(0x4);

	mxc_iomux_v3_setup_pad(iomux_setting);

    nimbus_led_ctrl(LEDID_WLAN,0,0);
    nimbus_led_ctrl(LEDID_WIFI,0,0);
    nimbus_led_ctrl(LEDID_CHARGER_RED,0,0);
    nimbus_led_ctrl(LEDID_CHARGER_GREEN,0,0);
    
    #if 0
    printk("Clear SD changer before suspending.\n");
    gpio_direction_output(SD1_CHANGE_CLEAR,1); 
    mdelay(1);
    gpio_direction_output(SD1_CHANGE_CLEAR,0); 
    #endif

}

开发者ID:SanDisk-Open-Source，项目名称:wireless-media-drive，代码行数:22，代码来源:mx50_rdp_nimbus.c

示例17: IMX_GPIO_NR

		.i2c_mode = MX7D_PAD_I2C2_SDA__I2C2_SDA | PC,
		.gpio_mode = MX7D_PAD_I2C2_SDA__GPIO4_IO11 | PC,
		.gp = IMX_GPIO_NR(4, 11),
	},
};
#endif

int dram_init(void)
{
	gd->ram_size = PHYS_SDRAM_SIZE;

	return 0;
}

static iomux_v3_cfg_t const uart1_pads[] = {
	MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
	MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
};

static iomux_v3_cfg_t const usdhc1_pads[] = {
	MX7D_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX7D_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX7D_PAD_SD1_DATA0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX7D_PAD_SD1_DATA1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX7D_PAD_SD1_DATA2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX7D_PAD_SD1_DATA3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),

	MX7D_PAD_GPIO1_IO08__SD1_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL),

	MX7D_PAD_SD1_CD_B__GPIO5_IO0    | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX7D_PAD_SD1_RESET_B__GPIO5_IO2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),

开发者ID:KunYi，项目名称:uboot-samx6i，代码行数:31，代码来源:mx7d_19x19_lpddr3_arm2.c

示例18: USDHC_PAD_CTRL

#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)

int dram_init(void)
{
    gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE);

    return 0;
}

iomux_v3_cfg_t const uart4_pads[] = {
    MX6_PAD_KEY_COL0__UART4_TXD | MUX_PAD_CTRL(UART_PAD_CTRL),
    MX6_PAD_KEY_ROW0__UART4_RXD | MUX_PAD_CTRL(UART_PAD_CTRL),
};

iomux_v3_cfg_t const usdhc3_pads[] = {
    MX6_PAD_SD3_CLK__USDHC3_CLK   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
    MX6_PAD_SD3_CMD__USDHC3_CMD   | MUX_PAD_CTRL(USDHC_PAD_CTRL),
    MX6_PAD_SD3_DAT0__USDHC3_DAT0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
    MX6_PAD_SD3_DAT1__USDHC3_DAT1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
    MX6_PAD_SD3_DAT2__USDHC3_DAT2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
    MX6_PAD_SD3_DAT3__USDHC3_DAT3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
    MX6_PAD_SD3_DAT4__USDHC3_DAT4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
    MX6_PAD_SD3_DAT5__USDHC3_DAT5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
    MX6_PAD_SD3_DAT6__USDHC3_DAT6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
    MX6_PAD_SD3_DAT7__USDHC3_DAT7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
    MX6_PAD_NANDF_CS0__GPIO_6_11  | MUX_PAD_CTRL(NO_PAD_CTRL), /* CD */

开发者ID:gitter-badger，项目名称:ARRR，代码行数:31，代码来源:mx6qarm2.c

示例19: gpio_direction_output

		gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 1);
		mdelay(10);
	}

	for (i = 0; i < ARRAY_SIZE(cm_fx6_issd_gpios); i++) {
		gpio_direction_output(cm_fx6_issd_gpios[i], on);
		udelay(100);
	}

	if (!on) /* for compatibility lower the power loss interrupt */
		gpio_direction_output(CM_FX6_SATA_PWLOSS_INT, 0);
}

static iomux_v3_cfg_t const sata_pads[] = {
	/* SATA PWR */
	IOMUX_PADS(PAD_ENET_TX_EN__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL)),
	IOMUX_PADS(PAD_EIM_A22__GPIO2_IO16    | MUX_PAD_CTRL(NO_PAD_CTRL)),
	IOMUX_PADS(PAD_EIM_D20__GPIO3_IO20    | MUX_PAD_CTRL(NO_PAD_CTRL)),
	IOMUX_PADS(PAD_EIM_A25__GPIO5_IO02    | MUX_PAD_CTRL(NO_PAD_CTRL)),
	/* SATA CTRL */
	IOMUX_PADS(PAD_ENET_TXD0__GPIO1_IO30  | MUX_PAD_CTRL(NO_PAD_CTRL)),
	IOMUX_PADS(PAD_EIM_D23__GPIO3_IO23    | MUX_PAD_CTRL(NO_PAD_CTRL)),
	IOMUX_PADS(PAD_EIM_D29__GPIO3_IO29    | MUX_PAD_CTRL(NO_PAD_CTRL)),
	IOMUX_PADS(PAD_EIM_A23__GPIO6_IO06    | MUX_PAD_CTRL(NO_PAD_CTRL)),
	IOMUX_PADS(PAD_EIM_BCLK__GPIO6_IO31   | MUX_PAD_CTRL(NO_PAD_CTRL)),
};

static void cm_fx6_setup_issd(void)
{
	SETUP_IOMUX_PADS(sata_pads);
	/* Make sure this gpio has logical 0 value */

开发者ID:RobertCNelson，项目名称:debian-u-boot，代码行数:31，代码来源:cm_fx6.c

示例20: MUX_PAD_CTRL

#include <asm/mach/map.h>

#include <mach/hardware.h>
#include <mach/common.h>
#include <mach/iomux-mx51.h>
#include <mach/audmux.h>

#include "devices-imx51.h"
#include "devices.h"

static iomux_v3_cfg_t eukrea_mbimxsd_pads[] = {
	/* LED */
	MX51_PAD_NANDF_D10__GPIO3_30,
	/* SWITCH */
	_MX51_PAD_NANDF_D9__GPIO3_31 | MUX_PAD_CTRL(PAD_CTL_PUS_22K_UP |
			PAD_CTL_PKE | PAD_CTL_SRE_FAST |
			PAD_CTL_DSE_HIGH | PAD_CTL_PUE | PAD_CTL_HYS),
	/* UART2 */
	MX51_PAD_UART2_RXD__UART2_RXD,
	MX51_PAD_UART2_TXD__UART2_TXD,
	/* UART 3 */
	MX51_PAD_UART3_RXD__UART3_RXD,
	MX51_PAD_UART3_TXD__UART3_TXD,
	MX51_PAD_KEY_COL4__UART3_RTS,
	MX51_PAD_KEY_COL5__UART3_CTS,
	/* SD */
	MX51_PAD_SD1_CMD__SD1_CMD,
	MX51_PAD_SD1_CLK__SD1_CLK,
	MX51_PAD_SD1_DATA0__SD1_DATA0,
	MX51_PAD_SD1_DATA1__SD1_DATA1,
	MX51_PAD_SD1_DATA2__SD1_DATA2,

开发者ID:CSCLOG，项目名称:beaglebone，代码行数:31，代码来源:eukrea_mbimxsd-baseboard.c

注：本文中的MUX_PAD_CTRL函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ MVM_ASSIGN_REF函数代码示例发布时间：2022-05-30

C++ MUTEX_UNLOCK函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：18215|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9658|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8168|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8543|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8449|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9375|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8420|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7855|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8405|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7391|2022-11-06

客服电话

电子邮件

C++ MUX_PAD_CTRL函数代码示例

示例1: setup_epdc

示例2: setup_epdc_power

示例3: setup_epdc_power

示例4: setup_epdc_power

示例5: setup_iomux_uart

示例6: cm_fx6_setup_usb_host

示例7: mx50_suspend_exit

示例8: nimbus_gpio_iomux_init

示例9: cm_fx6_init_usb_otg

示例10: board_eth_init

示例11: mx51_babbage_init

示例12: cm_fx6_usb_hub_reset

示例13: board_init

示例14: board_ehci_hcd_init

示例15: mx50_suspend_enter

示例16: nimbus_gpio_iomux_deinit

示例17: IMX_GPIO_NR

示例18: USDHC_PAD_CTRL

示例19: gpio_direction_output

示例20: MUX_PAD_CTRL

请发表评论

全部评论

上一篇：

下一篇：

librespeed/speedtest: Self-hosted Speedt

avehtari/BDA_m_demos: Bayesian Data Anal

四维彩超怎么看性别？四维看男孩女孩诀窍

TUNER88/iOSSystemSoundsLibrary: List of

medfreeman/markdown-it-toc-and-anchor: m

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053