C++ send_data_cmd函数代码示例

OGeek|极客世界-中国程序员成长平台 › 门户 › 编程› C++›C++教程

原作者: [db:作者] 来自: [db:来源] 收藏邀请

本文整理汇总了C++中send_data_cmd函数的典型用法代码示例。如果您正苦于以下问题：C++ send_data_cmd函数的具体用法？C++ send_data_cmd怎么用？C++ send_data_cmd使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。

在下文中一共展示了send_data_cmd函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。

示例1: lcm_update_black

static void  lcm_update_black(unsigned int x, unsigned int y,unsigned int width, unsigned int height, unsigned short data)
{
    unsigned int x0 = x;
    unsigned int y0 = y;
    unsigned int x1 = x0 + width;
    unsigned int y1 = y0 + height + 2;
    unsigned int k, i;

	send_ctrl_cmd(0x2A);
	send_data_cmd(HIGH_BYTE(x0));
	send_data_cmd(LOW_BYTE(x0));
	send_data_cmd(HIGH_BYTE(x1));
	send_data_cmd(LOW_BYTE(x1));

	send_ctrl_cmd(0x2B);
	send_data_cmd(HIGH_BYTE(y0));
	send_data_cmd(LOW_BYTE(y0));
	send_data_cmd(HIGH_BYTE(y1));
	send_data_cmd(LOW_BYTE(y1));
	send_ctrl_cmd(0x2C);

	for (i = x0; i < x1; i++)
	{
		for (k = y0; k < y1; k++)
		{
			send_data_cmd(data);
			send_data_cmd(data);
		}
	}
	
}

开发者ID:4Fwolf，项目名称:lcm_drivers，代码行数:31，代码来源:zes588_hx8363b.c

示例2: lcm_compare_id

static unsigned int lcm_compare_id(void)
{

    unsigned int    id1 = 0;
    unsigned int    id2 = 0;
    unsigned int    id = 0;

    //unsigned char data[4];
    
//#ifdef BUILD_LK
    //unsigned int    lcm_idpin_value = 0;
   // lcm_idpin_value = lcm_check_idpin_adc(ADC_CHECK_COUNT);
//#endif
    config_gpio();//config gpio before use spi
    MDELAY(1);
    SET_RESET_PIN(1);
    MDELAY(10);
    SET_RESET_PIN(0);
    MDELAY(50);
    SET_RESET_PIN(1);
    MDELAY(120);

    send_ctrl_cmd(0xb0);
    //send_data_cmd(0x83);//bit7=7,sdo disable,sdo/sdi use the same pin
    send_data_cmd(0x03);//bit7=0,sdo en

    send_ctrl_cmd(0xfb);
    send_data_cmd(0x12);

    id1=spi_get_data(0xd3);

    send_ctrl_cmd(0xfb);
    send_data_cmd(0x13);
    id2=spi_get_data(0xd3);

    id = (id1<<8)|id2;//ic id
    
#ifdef BUILD_LK
    printf("by35hh_lcd_id=0x%x \r\n",id);
    //printf("by35hp_lcd_id data=0x%x,0x%x,0x%x,0x%x \r\n",data[0],data[1],data[2],data[3]);
#else
    printk("by35hh_lcd_id=0x%x\r\n",id);
#endif


//#ifdef BUILD_LK
   // if(/*(LCM_ID == id) || */( lcm_idpin_value >= 190))//id pin voltage is about 2.0v
//#else       
    if(LCM_ID == id)
//#endif
    {
        return 1;
    }
    else
    {
        return 0;
    }
    //return (LCM_ID == id)?1:0;

}

开发者ID:aleksandar9999a，项目名称:acer-z120-kernel-3.4.0，代码行数:60，代码来源:by35hh10t7c_hvga_rm68140.c

示例3: lcm_resume

static void lcm_resume(void)
{
	#if 1
	send_ctrl_cmd(0x1100);
	MDELAY(120);	
	send_ctrl_cmd(0x2900);
	MDELAY(50);
	#else
	unsigned int lcd_id = 0;
	
	SET_RESET_PIN(1);
	MDELAY(5);
    SET_RESET_PIN(0);
    MDELAY(50);  
    SET_RESET_PIN(1);
    MDELAY(100);  // 400

	send_ctrl_cmd(0xB9); 
	send_data_cmd(0xFF); 
	send_data_cmd(0x83); 
	send_data_cmd(0x63); 
	UDELAY(10);
	
	lcd_id = get_lcd_id_n(LCM_ID_REG, 2) & 0xFF;
	LCD_PRINT(LCM_NAME"lcm_resume: lcd_id = 0x%x\n", lcd_id);

    init_lcm_registers();
	#endif
}

开发者ID:4Fwolf，项目名称:lcm_drivers，代码行数:29，代码来源:zes588_hx8363b.c

示例4: lcm_compare_id

static unsigned int lcm_compare_id(void)
{	
	unsigned int lcd_id = 0;

	SET_RESET_PIN(1);
	MDELAY(5);
    SET_RESET_PIN(0);
    MDELAY(50);  
    SET_RESET_PIN(1);
    MDELAY(120);

	send_ctrl_cmd(0xF000);send_data_cmd(0x55);
	send_ctrl_cmd(0xF001);send_data_cmd(0xAA);
	send_ctrl_cmd(0xF002);send_data_cmd(0x52);
	send_ctrl_cmd(0xF003);send_data_cmd(0x08);
	send_ctrl_cmd(0xF004);send_data_cmd(0x01);
	UDELAY(10);

	lcd_id = get_lcd_id_r(LCM_ID_REG) & 0xFF;
	lcd_id = (lcd_id << 8) | (get_lcd_id_r(LCM_ID_REG + 1) & 0xFF);

	LCD_PRINT(LCM_NAME"lcm_compare_id: lcd_id = 0x%x\n", lcd_id);

		
    return (LCM_ID == lcd_id)?1:0;
}

开发者ID:4Fwolf，项目名称:lcm_drivers，代码行数:26，代码来源:rfd402_nt35510.c

示例5: lcm_resume

static void lcm_resume(void)
{
	#if 1
	send_ctrl_cmd(0x11);
	MDELAY(120);
	send_ctrl_cmd(0x29);
	MDELAY(50);
	#else
	unsigned int lcd_id = 0;
	
	SET_RESET_PIN(1);
	MDELAY(5);
    SET_RESET_PIN(0);
    MDELAY(20);  
    SET_RESET_PIN(1);
    MDELAY(20);  // 400

	send_ctrl_cmd(0xB9);
	send_data_cmd(0xFF);
	send_data_cmd(0x83);
	send_data_cmd(0x57);

	UDELAY(10);

	lcd_id = get_lcd_id_n(LCMID_REG, 2);
	LCD_PRINT("[JINCHI35_HX8357C]lcm_resume: lcd_id = 0x%x\n", lcd_id);

#if 0//ndef BUILD_UBOOT
	print_lcm_registers();
#endif

	init_lcm_registers();	
	#endif
}

开发者ID:ariafan，项目名称:Fly_IQ255_Firmware_Build，代码行数:34，代码来源:luckasfb_hx8357c.c

示例6: lcm_update_black

static void  lcm_update_black(unsigned int x, unsigned int y,unsigned int width, unsigned int height, unsigned short data)
{
    unsigned int x0 = x;
    unsigned int y0 = y;
    unsigned int x1 = x0 + width;
    unsigned int y1 = y0 + height + 2;
    unsigned int k, i;

	set_lcm_register(0x2A00, HIGH_BYTE(x0),  0);
	set_lcm_register(0x2A01, LOW_BYTE(x0),  0);
	set_lcm_register(0x2A02, HIGH_BYTE(x1),  0);
	set_lcm_register(0x2A03, LOW_BYTE(x1),  0);
	set_lcm_register(0x2B00, HIGH_BYTE(y0),  0);
	set_lcm_register(0x2B01, LOW_BYTE(y0),  0);
	set_lcm_register(0x2B02, HIGH_BYTE(y1),  0);  
	set_lcm_register(0x2B03, LOW_BYTE(y1),  0);

	send_ctrl_cmd(0x2C00);

	for (i = x0; i < x1; i++)
	{
		for (k = y0; k < y1; k++)
		{
			send_data_cmd(data);
			send_data_cmd(data);
		}
	}
	
}

开发者ID:4Fwolf，项目名称:lcm_drivers，代码行数:29，代码来源:rfd402_nt35510.c

示例7: lcm_resume

static void lcm_resume(void)
{
	#if 1
	send_ctrl_cmd(0x1100);
	MDELAY(120);	
	send_ctrl_cmd(0x2900);
	MDELAY(50);
	#else
	unsigned int lcd_id = 0;
	
	SET_RESET_PIN(1);
	MDELAY(5);
    SET_RESET_PIN(0);
    MDELAY(50);  
    SET_RESET_PIN(1);
    MDELAY(100);  // 400

	send_ctrl_cmd(0xF000);send_data_cmd(0x55);
	send_ctrl_cmd(0xF001);send_data_cmd(0xAA);
	send_ctrl_cmd(0xF002);send_data_cmd(0x52);
	send_ctrl_cmd(0xF003);send_data_cmd(0x08);
	send_ctrl_cmd(0xF004);send_data_cmd(0x01);
	UDELAY(10);
	
	lcd_id = get_lcd_id_r(LCM_ID_REG) & 0xFF;
	lcd_id = (lcd_id << 8) | (get_lcd_id_r(LCM_ID_REG + 1) & 0xFF);

	LCD_PRINT(LCM_NAME"lcm_resume: lcd_id = 0x%x\n", lcd_id);

    init_lcm_registers();
	#endif
}

开发者ID:4Fwolf，项目名称:lcm_drivers，代码行数:32，代码来源:rfd402_nt35510.c

示例8: lcm_compare_id

static unsigned int lcm_compare_id(void)
{	
	 unsigned int id = 0,ID_PIN =2;
    send_ctrl_cmd(0xB9);  // SET password
	send_data_cmd(0xFF);  
	send_data_cmd(0x83);  
	send_data_cmd(0x69);
    send_ctrl_cmd(0xC3);
	send_data_cmd(0xFF);

	send_ctrl_cmd(0xF4);
	read_data_cmd();
	id = read_data_cmd();
#if defined(BUILD_LK)
	printf("xxxxx MYCAT hx8369_p908 READ ID = 0x%x\n", id);
#else
	printk("xxxxx MYCAT hx8369_p908 READ ID = 0x%x\n", id);
#endif
	mt_set_gpio_mode(GPIO_LCD_ID_PIN,0);
	mt_set_gpio_dir(GPIO_LCD_ID_PIN,0);
	mt_set_gpio_pull_enable(GPIO_LCD_ID_PIN,1);
	mt_set_gpio_pull_select(GPIO_LCD_ID_PIN,1);
	MDELAY(1);
	
	ID_PIN=mt_get_gpio_in(GPIO_LCD_ID_PIN);
#if defined(BUILD_LK)
	printf("xxxxx MYCAT ID_PIN = 0x%x\n", ID_PIN);
#else
	printk("xxxxx MYCAT ID_PIN = 0x%x\n", ID_PIN);
#endif
//    return ((LCM_ID == id)&&(ID_PIN==0))?1:0;
    return (LCM_ID == id)?1:0;
}

开发者ID:SeriniTY320，项目名称:mediatek，代码行数:33，代码来源:hx8369a_HUARUI_MS_HX450939FP_BOE_mcu18_fwvga.c

示例9: lcm_init

static void lcm_init(void)
{
	//unsigned int lcd_id = 0;
	
	SET_RESET_PIN(1);
	MDELAY(10);
	SET_RESET_PIN(0);
	MDELAY(100);
	SET_RESET_PIN(1);

    // Advises that should hold high level for about 120 ms as for HX... series lcd ic
    MDELAY(120);
	//MDELAY(50);

	//lcd_id = get_lcd_id_n(LCMID_REG, 2);
	//LCD_PRINT("[XXD35_ILI9486L]lcm_init: lcd_id = 0x%x\n", lcd_id);

	init_lcm_registers();
	lcm_update_black(0, 0, FRAME_WIDTH, FRAME_HEIGHT, 0x00);

    #if 0
    //Set TE register
	send_ctrl_cmd(0x35);
	send_data_cmd(0x00);

    send_ctrl_cmd(0X0044);  // Set TE signal delay scanline
    send_data_cmd(0X0000);  // Set as 0-th scanline
    send_data_cmd(0X0000);
	//sw_clear_panel(0);
    #endif
}

开发者ID:ariafan，项目名称:Fly_IQ255_Firmware_Build，代码行数:31，代码来源:luckasfb_hx8357c.c

示例10: lcm_compare_id

static unsigned int lcm_compare_id(void)
{

    unsigned int    id1 = 0;
    unsigned int    id2 = 0;
    unsigned int    id = 0;
#ifdef BUILD_LK
    unsigned int    lcm_idpin_value = 0;
    lcm_idpin_value = lcm_check_idpin_adc(ADC_CHECK_COUNT);
#endif
    config_gpio();
    SET_RESET_PIN(1);
    MDELAY(1);
    SET_RESET_PIN(0);
    MDELAY(20);
    SET_RESET_PIN(1);
    MDELAY(120);

    //send_ctrl_cmd(0xb0);

    send_ctrl_cmd(0xb0);
    //send_data_cmd(0x83);//bit7=7,sdo disable,sdo/sdi use the same pin
    send_data_cmd(0x03);//bit7=0,sdo en

    send_ctrl_cmd(0xfb);
    send_data_cmd(0x12);
#if 0
    id=spi_get_data(0xdb);//vendor id
#else
    id1=spi_get_data(0xd3);

    send_ctrl_cmd(0xfb);
    send_data_cmd(0x13);
    id2=spi_get_data(0xd3);

    id = (id1<<8)|id2;//ic id
#endif
#ifdef BUILD_LK
    printf("TXD9487_lcd_id1=0x%x,lcd_id2=0x%x,lcd_id=0x%x  \r\n",id1,id2,id);
#else
    printk("TXD9487_lcd_id1=0x%x,lcd_id2=0x%x,lcd_id=0x%x  \r\n",id1,id2,id);
#endif


#ifdef BUILD_LK
    if(/*(LCM_ID == id) || */( lcm_idpin_value > 140) && ( lcm_idpin_value <190))//id pin voltage is about 1.5v
#else       
    if(LCM_ID == id)
#endif
    {
        return 1;
    }
    else
    {
        return 0;
    }
    //return (LCM_ID == id)?1:0;

}

开发者ID:4Fwolf，项目名称:lcm_drivers，代码行数:59，代码来源:txd350nh_hvga_ili9487.c

示例11: lcm_compare_id

static unsigned int lcm_compare_id(void)
{

    unsigned int    id = 0;

    //unsigned char data[4];
    
//#ifdef BUILD_LK
   // unsigned int    lcm_idpin_value = 0;
   // lcm_idpin_value = lcm_check_idpin_adc(ADC_CHECK_COUNT);
//#endif
    config_gpio();//config gpio before use spi
    MDELAY(1);
    SET_RESET_PIN(1);
    MDELAY(10);
    SET_RESET_PIN(0);
    MDELAY(50);
    SET_RESET_PIN(1);
    MDELAY(120);

    send_ctrl_cmd(0xB9); //EXTC
    send_data_cmd(0xFF); //EXTC
    send_data_cmd(0x83); //EXTC
    send_data_cmd(0x57); //EXTC
    MDELAY(15);

    send_ctrl_cmd(0xB3);
    send_data_cmd(0xC3);	
    //for himax8357C
    send_ctrl_cmd(0xFE);
    send_data_cmd(0xD0);
    MDELAY(20);
    id=spi_get_data(0xff);
    //id=spi_get_bytes(0xff,data);
    
#ifdef BUILD_LK
    printf("by35hp_lcd_id=0x%x \r\n",id);
    //printf("by35hp_lcd_id data=0x%x,0x%x,0x%x,0x%x \r\n",data[0],data[1],data[2],data[3]);
#else
    printk("by35hp_lcd_id=0x%x\r\n",id);
#endif


//#ifdef BUILD_LK
    //if(/*(LCM_ID == id) || */( lcm_idpin_value >= 190))//id pin voltage is about 2.0v
//#else       
    if(LCM_ID == id)
//#endif
    {
        return 1;
    }
    else
    {
        return 0;
    }
    //return (LCM_ID == id)?1:0;

}

开发者ID:aleksandar9999a，项目名称:acer-z120-kernel-3.4.0，代码行数:58，代码来源:by35hp_hvga_hx8357.c

示例12: lcm_set_pwm

static void lcm_set_pwm(unsigned int divider)
{
#if 0
 send_ctrl_cmd(0xBE);
 send_data_cmd(0xFF);

 send_ctrl_cmd(0xBF);
 send_data_cmd(0x07);
#endif
}

开发者ID:kelvinbui31，项目名称:android_mediatek_muse72，代码行数:10，代码来源:ili9340d_dbi_qvga_s5.c

示例13: lcm_compare_id

static unsigned int lcm_compare_id(void)
{

    unsigned int    id = 0;

    //unsigned char data[4];
    
#ifdef BUILD_LK
    unsigned int    lcm_idpin_value = 0;
    lcm_idpin_value = lcm_check_idpin_adc(ADC_CHECK_COUNT);
#endif
    SET_RESET_PIN(1);
    MDELAY(10);
    SET_RESET_PIN(0);
    MDELAY(50);
    SET_RESET_PIN(1);
    MDELAY(120);

    send_ctrl_cmd(0xB9); //EXTC
    send_data_cmd(0xFF); //EXTC
    send_data_cmd(0x83); //EXTC
    send_data_cmd(0x57); //EXTC
    MDELAY(15);

    send_ctrl_cmd(0xB3);
    send_data_cmd(0xC3);	
    //for himax8357C
    send_ctrl_cmd(0xFE);
    send_data_cmd(0xD0);
    MDELAY(20);
    id=spi_get_data(0xff);
    //id=spi_get_bytes(0xff,data);
    
#ifdef BUILD_LK
    printf("jmo4861_lcd_id=0x%x \r\n",id);
    //printf("jmo4861_lcd_id data=0x%x,0x%x,0x%x,0x%x \r\n",data[0],data[1],data[2],data[3]);
#else
    printk("jmo4861_lcd_id=0x%x\r\n",id);
#endif

#ifdef BUILD_LK
    if(/*(LCM_ID == id) || */( lcm_idpin_value > 140) && ( lcm_idpin_value <190))//id pin voltage is about 1.5v
#else       
    if(LCM_ID == id)
#endif
    {
        return 1;
    }
    else
    {
        return 0;
    }
    //return (LCM_ID == id)?1:0;

}

开发者ID:aleksandar9999a，项目名称:acer-z120-kernel-3.4.0，代码行数:55，代码来源:jmo4861_hvga_hx8357.c

示例14: lcm_setbacklight

static void lcm_setbacklight(unsigned int level)
{
	if(level > 255) level = 255;
#if 0
	send_ctrl_cmd(0x51);
	send_data_cmd(level);
#else
    send_ctrl_cmd(0xBE);
    send_data_cmd(0x0F);
#endif
}

开发者ID:kelvinbui31，项目名称:android_mediatek_muse72，代码行数:11，代码来源:ili9340d_dbi_qvga_s5.c

示例15: lcm_compare_id

static unsigned int lcm_compare_id(void)
{	
    send_ctrl_cmd(0xB9);  // SET password
	send_data_cmd(0xFF);  
	send_data_cmd(0x83);  
	send_data_cmd(0x69);
    send_ctrl_cmd(0xC3);
	send_data_cmd(0xFF);

	send_ctrl_cmd(0xF4);
	read_data_cmd();
    return (LCM_ID == read_data_cmd())?1:0;
}

开发者ID:4Fwolf，项目名称:lcm_drivers，代码行数:13，代码来源:hx8369_hvga.c

示例16: lcm_update

static void lcm_update(unsigned int x, unsigned int y, unsigned int width, unsigned int height)
{
	unsigned short x0, y0, x1, y1;
	unsigned short h_X_start, l_X_start, h_X_end, l_X_end, h_Y_start, l_Y_start, h_Y_end, l_Y_end;

	x0 = (unsigned short)x;
	y0 = (unsigned short)y;
	x1 = (unsigned short)x + width - 1;
	y1 = (unsigned short)y + height - 1;

	h_X_start = (x0 & 0xFF00) >> 8;
	l_X_start = x0 & 0x00FF;
	h_X_end = (x1 & 0xFF00) >> 8;
	l_X_end = x1 & 0x00FF;

	h_Y_start = (y0 & 0xFF00) >> 8;
	l_Y_start = y0 & 0x00FF;
	h_Y_end = (y1 & 0xFF00) >> 8;
	l_Y_end = y1 & 0x00FF;

	send_ctrl_cmd(0x2A);
	send_data_cmd(h_X_start);
	send_data_cmd(l_X_start);
	send_data_cmd(h_X_end);
	send_data_cmd(l_X_end);

	send_ctrl_cmd(0x2B);
	send_data_cmd(h_Y_start);
	send_data_cmd(l_Y_start);
	send_data_cmd(h_Y_end);
	send_data_cmd(l_Y_end);

	send_ctrl_cmd(0x2C);
}

开发者ID:John677，项目名称:Kernal_k3note，代码行数:34，代码来源:st7789h2_dbi.c

示例17: sw_clear_panel

static void sw_clear_panel(unsigned int color)
{
    unsigned int x0 = 0;
    unsigned int y0 = 0;
    unsigned int x1 = x0 + FRAME_WIDTH - 1;
    unsigned int y1 = y0 + FRAME_HEIGHT - 1;

    unsigned int x, y;

    send_ctrl_cmd(0x2A); 
    send_data_cmd(HIGH_BYTE(x0));
  	send_data_cmd(LOW_BYTE(x0));
    send_data_cmd(HIGH_BYTE(x1));
  	send_data_cmd(LOW_BYTE(x1));

  	send_ctrl_cmd(0x2B); 
    send_data_cmd(HIGH_BYTE(y0));
  	send_data_cmd(LOW_BYTE(y0));
    send_data_cmd(HIGH_BYTE(y1));
  	send_data_cmd(LOW_BYTE(y1));

	send_ctrl_cmd(0x2C);    // send DDRAM set

    // 18-bit mode (256K color) coding
    for (y = y0; y <= y1; ++ y) {
        for (x = x0; x <= x1; ++ x) {
            lcm_util.send_data(color);
        }
    }
}

开发者ID:4Fwolf，项目名称:lcm_drivers，代码行数:30，代码来源:lcm_drv.c

示例18: lcm_resume

static void lcm_resume(void)
{
#if 1
    // truely's patch for BT UART noise issue
    send_ctrl_cmd(0xD0);
    send_data_cmd(0x07);
    send_data_cmd(0x42);
    send_data_cmd(0x1D);
	MDELAY(200);
#endif

	send_ctrl_cmd(0x11);
	MDELAY(120);
	send_ctrl_cmd(0x29);
	MDELAY(100);            // wait for LCM is stable to show
}

开发者ID:4Fwolf，项目名称:lcm_drivers，代码行数:16，代码来源:lcm_drv.c

示例19: lcm_setbacklight

static void lcm_setbacklight(unsigned int level)
{
   if(level > 255) level = 255;

   send_ctrl_cmd(0x51);
   send_data_cmd(level);	
}

开发者ID:4Fwolf，项目名称:ALCATEL_LCM，代码行数:7，代码来源:hx8369_mcu_6572.c

示例20: lcm_suspend

static void lcm_suspend(void)
{
	send_ctrl_cmd(0x28);

#if 1
    // truely's patch for BT UART noise issue
    send_ctrl_cmd(0xD0);
    send_data_cmd(0x05);
    send_data_cmd(0x47);
    send_data_cmd(0x1D);
	MDELAY(200);
#endif

	send_ctrl_cmd(0x10);
	MDELAY(10);
}

开发者ID:4Fwolf，项目名称:lcm_drivers，代码行数:16，代码来源:lcm_drv.c

注：本文中的send_data_cmd函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。

鲜花

握手

雷人

路过

鸡蛋

该文章已有0人参与评论

请发表评论

全部评论

专题导读

More+

10-27 六六分期app的软件客服如何联系？(六六分期

11-06 可心卡盟:win10系统火狐flash插件崩溃怎么

11-06 亲亲特价:怎么删除回收站图标

11-06 济南大学虚拟社区:鲁大师节能降温的具体办

11-06 xlueops.exe:无线网络安装向导

11-06 女斗合众国:win7系统cf与主机连接不稳定怎

11-06 0xc000022-[cf烟雾头]cf怎么调烟雾头

11-06 qizideyouhuo:应用程序无法正常启动0xc0000

11-06 ipz-185:win7系统vcf文件怎么打开

11-06 傻哥蹦迪:win10系统s4怎么打开usb调试

11-06 八神浩树gtaste:回收站清空了怎么恢复

11-06 妖尾之黑色守护:win10系统电脑没有1440x900

11-06 校园至尊魔王小说:win7系统浏览网页时字体

11-06 女斗合众国:win10系统访问共享文件夹提示请

11-06 tokyo hot n0654:恢复win7系统默认字体一招

11-06 雨酷仙境:设置win7系统转移临时文件夹腾出

11-06 阿穆纳伊之杖:win7系统开始菜单在右边还原

11-06 tunespotting:win10系统火狐flash插件总是

11-06 甘尔葛分析师：计谋网站seo关键词暴涨有什

11-06 蔡贵霖: 计谋网站seo关键词暴涨有什么秘密

11-06 博益网首页:ao3网页版进入不了解决方法

11-06 漏斗子专栏: 网站数据分析小白易懂精华篇

11-06 见证双虹怎么做:win7系统开启telnet命令的

11-06 颾狐蝶蜋:系统资源不足无法完成请求的服务

11-06 国光中学校歌:提交网站到alexa查询详细步骤

11-06 西安有情天:静态网页和动态网页的区别

11-06 红木雅尚斋:外部链接构造对网站的好处

11-06 前官礼遇：防止域名劫持–增强域安全性的10

11-06 密传二转答案: 中文分词算法有哪些

11-06 金泉家园邮编:百度快照劫持的表现及应对方

C++ send_error函数代码示例发布时间：2022-05-30

C++ send_data函数代码示例发布时间：2022-05-30

剪的笔顺,诠释剪的笔画,认识剪的部首

1 六六分期app的软件客服如何联系？(六六分期

六六分期app的软件客服如何联系？不知道吗？加qq群【895510560】即可！标题：六六分期

阅读：17943|2023-10-27

2 可心卡盟:win10系统火狐flash插件崩溃怎么

今天小编告诉大家如何处理win10系统火狐flash插件总是崩溃的问题，可能很多用户都不知

阅读：9562|2022-11-06

3 亲亲特价:怎么删除回收站图标

今天小编告诉大家如何对win10系统删除桌面回收站图标进行设置，可能很多用户都不知道

阅读：8126|2022-11-06

4 济南大学虚拟社区:鲁大师节能降温的具体办

今天小编告诉大家如何对win10系统电脑设置节能降温的设置方法，想必大家都遇到过需要

阅读：8505|2022-11-06

5 xlueops.exe:无线网络安装向导

我们在使用xp系统的过程中,经常需要对xp系统无线网络安装向导设置进行设置，可能很多

阅读：8409|2022-11-06

6 女斗合众国:win7系统cf与主机连接不稳定怎

今天小编告诉大家如何处理win7系统玩cf老是与主机连接不稳定的问题，可能很多用户都不

阅读：9299|2022-11-06

7 0xc000022-[cf烟雾头]cf怎么调烟雾头

电脑对日常生活的重要性小编就不多说了，可是一旦碰到win7系统设置cf烟雾头的问题，很

阅读：8373|2022-11-06

8 qizideyouhuo:应用程序无法正常启动0xc0000

我们在日常使用电脑的时候，有的小伙伴们可能在打开应用的时候会遇见提示应用程序无法

阅读：7805|2022-11-06

9 ipz-185:win7系统vcf文件怎么打开

今天小编告诉大家如何对win7系统打开vcf文件进行设置，可能很多用户都不知道怎么对win

阅读：8356|2022-11-06

10 傻哥蹦迪:win10系统s4怎么打开usb调试

今天小编告诉大家如何对win10系统s4开启USB调试模式进行设置，可能很多用户都不知道怎

阅读：7358|2022-11-06

客服电话

电子邮件

C++ send_data_cmd函数代码示例

示例1: lcm_update_black

示例2: lcm_compare_id

示例3: lcm_resume

示例4: lcm_compare_id

示例5: lcm_resume

示例6: lcm_update_black

示例7: lcm_resume

示例8: lcm_compare_id

示例9: lcm_init

示例10: lcm_compare_id

示例11: lcm_compare_id

示例12: lcm_set_pwm

示例13: lcm_compare_id

示例14: lcm_setbacklight

示例15: lcm_compare_id

示例16: lcm_update

示例17: sw_clear_panel

示例18: lcm_resume

示例19: lcm_setbacklight

示例20: lcm_suspend

请发表评论

全部评论

上一篇：

下一篇：

bradtraversy/iweather: Ionic 3 mobile we

断牙刷新位置时间（断牙属性及刷新位置介绍

MATLAB命令大全

更的笔顺,体会更的笔画,理会更的部首

ecki/net-tools: Linux base networking to

剪的笔顺,诠释剪的笔画,认识剪的部首

六六分期app的软件客服如何联系？(六六分期

florent37/ViewAnimator: A fluent Android

florent37/Shrine-MaterialDesign2: implem

CVE-2020-36276

SimpleSoftwareIO/simple-sms: Send and re

关于我们

产品与服务

解决方案

139-2527-9053