本文整理汇总了C++中serial_in函数的典型用法代码示例。如果您正苦于以下问题：C++ serial_in函数的具体用法？C++ serial_in怎么用？C++ serial_in使用的例子？那么恭喜您, 这里精选的函数代码示例或许可以为您提供帮助。
在下文中一共展示了serial_in函数的20个代码示例，这些例子默认根据受欢迎程度排序。您可以为喜欢或者感觉有用的代码点赞，您的评价将有助于我们的系统推荐出更棒的C++代码示例。
示例1: omap_uart_active
int omap_uart_active(int num, u32 timeout)
{
struct uart_omap_port *up = ui[num];
struct circ_buf *xmit;
unsigned int status;
/* Though when UART's initialised this can never happen,
* but during initialisation, it can happen the "ui"
* structure is not initialized and the timer kicks
* in. This would result in a NULL value, resulting
* in crash.
*/
if (up == NULL)
return 0;
/* Check for recent driver activity. If time delta from now
* to last activty < "uart idle timeout" second keep clocks on.
*/
if (((jiffies - up->port_activity) < timeout))
return 1;
xmit = &up->port.state->xmit;
if (!(uart_circ_empty(xmit) || uart_tx_stopped(&up->port)))
return 1;
status = serial_in(up, UART_LSR);
/* TX hardware not empty */
if (!(status & (UART_LSR_TEMT | UART_LSR_THRE)))
return 1;
/* Any rx activity? */
if (status & UART_LSR_DR)
return 1;
/* Check if DMA channels are active */
if (up->use_dma && (up->uart_dma.rx_dma_channel != OMAP_UART_DMA_CH_FREE ||
up->uart_dma.tx_dma_channel != OMAP_UART_DMA_CH_FREE))
return 1;
return 0;
}
开发者ID:AdiPat，项目名称:i9003_Kernel，代码行数:41，代码来源:omap-serial.c
示例2: serial_pxa_console_write
/*
* Print a string to the serial port trying not to disturb
* any possible real use of the port...
*
* The console_lock must be held when we get here.
*/
static void
serial_pxa_console_write(struct console *co, const char *s, unsigned int count)
{
struct uart_pxa_port *up = &serial_pxa_ports[co->index];
unsigned int ier;
/*
* First save the IER then disable the interrupts
*/
ier = serial_in(up, UART_IER);
serial_out(up, UART_IER, UART_IER_UUE);
uart_console_write(&up->port, s, count, serial_pxa_console_putchar);
/*
* Finally, wait for transmitter to become empty
* and restore the IER
*/
wait_for_xmitr(up);
serial_out(up, UART_IER, ier);
}
开发者ID:mrtos，项目名称:Logitech-Revue，代码行数:27，代码来源:pxa.c
示例3: serial_omap_rdi
static void serial_omap_rdi(struct uart_omap_port *up, unsigned int lsr)
{
unsigned char ch = 0;
unsigned int flag;
if (!(lsr & UART_LSR_DR))
return;
ch = serial_in(up, UART_RX);
flag = TTY_NORMAL;
up->port.icount.rx++;
#ifdef CONFIG_CONSOLE_POLL
if (up->port.poll_rx_cb && up->port.poll_rx_cb(ch))
return;
#endif
if (uart_handle_sysrq_char(&up->port, ch))
return;
uart_insert_char(&up->port, lsr, UART_LSR_OE, ch, flag);
}
开发者ID:neominds，项目名称:wrfx227819，代码行数:21，代码来源:omap-serial.c
示例4: omap8250_set_mctrl
static void omap8250_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_8250_port *up = up_to_u8250p(port);
struct omap8250_priv *priv = up->port.private_data;
u8 lcr;
serial8250_do_set_mctrl(port, mctrl);
/*
* Turn off autoRTS if RTS is lowered and restore autoRTS setting
* if RTS is raised
*/
lcr = serial_in(up, UART_LCR);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
if ((mctrl & TIOCM_RTS) && (port->status & UPSTAT_AUTORTS))
priv->efr |= UART_EFR_RTS;
else
priv->efr &= ~UART_EFR_RTS;
serial_out(up, UART_EFR, priv->efr);
serial_out(up, UART_LCR, lcr);
}
开发者ID:Lyude，项目名称:linux，代码行数:21，代码来源:8250_omap.c
示例5: serial_omap_pm
static void
serial_omap_pm(struct uart_port *port, unsigned int state,
unsigned int oldstate)
{
struct uart_omap_port *up = (struct uart_omap_port *)port;
unsigned char efr;
dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->pdev->id);
serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
efr = serial_in(up, UART_EFR);
serial_out(up, UART_EFR, efr | UART_EFR_ECB);
serial_out(up, UART_LCR, 0);
serial_out(up, UART_IER, (state != 0) ? UART_IERX_SLEEP : 0);
serial_out(up, UART_LCR, OMAP_UART_LCR_CONF_MDB);
serial_out(up, UART_EFR, efr);
serial_out(up, UART_LCR, 0);
/* Enable module level wake up */
serial_out(up, UART_OMAP_WER,
(state != 0) ? OMAP_UART_WER_MOD_WKUP : 0);
}
开发者ID:AdiPat，项目名称:i9003_Kernel，代码行数:21，代码来源:omap-serial.c
示例6: ip3106_tx_chars
static void ip3106_tx_chars(struct ip3106_port *sport)
{
struct circ_buf *xmit = &sport->port.info->xmit;
if (sport->port.x_char) {
serial_out(sport, IP3106_FIFO, sport->port.x_char);
sport->port.icount.tx++;
sport->port.x_char = 0;
return;
}
/*
* Check the modem control lines before
* transmitting anything.
*/
ip3106_mctrl_check(sport);
if (uart_circ_empty(xmit) || uart_tx_stopped(&sport->port)) {
ip3106_stop_tx(&sport->port, 0);
return;
}
/*
* TX while bytes available
*/
while (((serial_in(sport, IP3106_FIFO) &
IP3106_UART_FIFO_TXFIFO) >> 16) < 16) {
serial_out(sport, IP3106_FIFO, xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
sport->port.icount.tx++;
if (uart_circ_empty(xmit))
break;
}
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&sport->port);
if (uart_circ_empty(xmit))
ip3106_stop_tx(&sport->port, 0);
}
开发者ID:BackupTheBerlios，项目名称:tew632-brp-svn，代码行数:40，代码来源:ip3106_uart.c
示例7: serial_pxa_tx_empty
static unsigned int serial_pxa_tx_empty(struct uart_port *port)
{
struct uart_pxa_port *up = (struct uart_pxa_port *)port;
unsigned long flags;
unsigned int ret;
spin_lock_irqsave(&up->port.lock, flags);
if (up->dma_enable) {
if (up->ier & UART_IER_DMAE) {
if (up->uart_dma.dma_status & TX_DMA_RUNNING) {
spin_unlock_irqrestore(&up->port.lock, flags);
return 0;
}
}
}
ret = serial_in(up, UART_LSR) & UART_LSR_TEMT ? TIOCSER_TEMT : 0;
spin_unlock_irqrestore(&up->port.lock, flags);
return ret;
}
开发者ID:GalaxyTab4，项目名称:maxicm_kernel_samsung_degaswifi，代码行数:22，代码来源:pxa.c
示例8: serial8250_get_mctrl
static unsigned int serial8250_get_mctrl(struct uart_port *port)
{
struct uart_8250_port *up = (struct uart_8250_port *)port;
unsigned long flags;
unsigned char status;
unsigned int ret;
spin_lock_irqsave(&up->port.lock, flags);
status = serial_in(up, UART_MSR);
spin_unlock_irqrestore(&up->port.lock, flags);
ret = 0;
if (status & UART_MSR_DCD)
ret |= TIOCM_CAR;
if (status & UART_MSR_RI)
ret |= TIOCM_RNG;
if (status & UART_MSR_DSR)
ret |= TIOCM_DSR;
if (status & UART_MSR_CTS)
ret |= TIOCM_CTS;
return ret;
}
开发者ID:FelipeFernandes1988，项目名称:Alice-1121-Modem，代码行数:22，代码来源:au1x00_uart.c
示例9: check_modem_status
static inline void check_modem_status(struct uart_hsu_port *up)
{
int status;
status = serial_in(up, UART_MSR);
if ((status & UART_MSR_ANY_DELTA) == 0)
return;
if (status & UART_MSR_TERI)
up->port.icount.rng++;
if (status & UART_MSR_DDSR)
up->port.icount.dsr++;
/* We may only get DDCD when HW init and reset */
if (status & UART_MSR_DDCD)
uart_handle_dcd_change(&up->port, status & UART_MSR_DCD);
/* Will start/stop_tx accordingly */
if (status & UART_MSR_DCTS)
uart_handle_cts_change(&up->port, status & UART_MSR_CTS);
wake_up_interruptible(&up->port.state->port.delta_msr_wait);
}
开发者ID:ANFS，项目名称:ANFS-kernel，代码行数:22，代码来源:mfd.c
示例10: serial_pxa_console_write
/*
* Print a string to the serial port trying not to disturb
* any possible real use of the port...
*
* The console_lock must be held when we get here.
*/
static void
serial_pxa_console_write(struct console *co, const char *s, unsigned int count)
{
struct uart_pxa_port *up = serial_pxa_ports[co->index];
unsigned int ier;
unsigned long flags;
int locked = 1;
clk_enable(up->clk);
local_irq_save(flags);
if (up->port.sysrq)
locked = 0;
else if (oops_in_progress)
locked = spin_trylock(&up->port.lock);
else
spin_lock(&up->port.lock);
/*
* First save the IER then disable the interrupts
*/
ier = serial_in(up, UART_IER);
serial_out(up, UART_IER, UART_IER_UUE);
uart_console_write(&up->port, s, count, serial_pxa_console_putchar);
/*
* Finally, wait for transmitter to become empty
* and restore the IER
*/
wait_for_xmitr(up);
serial_out(up, UART_IER, ier);
if (locked)
spin_unlock(&up->port.lock);
local_irq_restore(flags);
clk_disable(up->clk);
}
开发者ID:abhinav90，项目名称:linux，代码行数:44，代码来源:pxa.c
示例11: serial_omap_set_mctrl
//static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_omap_port *up = (struct uart_omap_port *)port;
unsigned char mcr = 0;
dev_dbg(up->port.dev, "serial_omap_set_mctrl+%d\n", up->pdev->id);
if (mctrl & TIOCM_RTS)
mcr |= UART_MCR_RTS;
if (mctrl & TIOCM_DTR)
mcr |= UART_MCR_DTR;
if (mctrl & TIOCM_OUT1)
mcr |= UART_MCR_OUT1;
if (mctrl & TIOCM_OUT2)
mcr |= UART_MCR_OUT2;
if (mctrl & TIOCM_LOOP)
mcr |= UART_MCR_LOOP;
serial_omap_port_enable(up);
up->mcr = serial_in(up, UART_MCR);
up->mcr |= mcr;
serial_out(up, UART_MCR, up->mcr);
serial_omap_port_disable(up);
}
开发者ID:manusreload，项目名称:android_kernel_huawei_omap4，代码行数:24，代码来源:omap-serial.c
示例12: serial_omap_pm
static void
serial_omap_pm(struct uart_port *port, unsigned int state,
unsigned int oldstate)
{
struct uart_omap_port *up = to_uart_omap_port(port);
unsigned char efr;
dev_dbg(up->port.dev, "serial_omap_pm+%d\n", up->port.line);
pm_runtime_get_sync(up->dev);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
efr = serial_in(up, UART_EFR);
serial_out(up, UART_EFR, efr | UART_EFR_ECB);
serial_out(up, UART_LCR, 0);
serial_out(up, UART_IER, (state != 0) ? UART_IERX_SLEEP : 0);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
serial_out(up, UART_EFR, efr);
serial_out(up, UART_LCR, 0);
pm_runtime_mark_last_busy(up->dev);
pm_runtime_put_autosuspend(up->dev);
}
开发者ID:DenisLug，项目名称:mptcp，代码行数:23，代码来源:omap-serial.c
示例13: serial_omap_set_mctrl
static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_omap_port *up = (struct uart_omap_port *)port;
unsigned char mcr = 0;
dev_dbg(up->port.dev, "serial_omap_set_mctrl+%d\n", up->port.line);
if (mctrl & TIOCM_RTS)
mcr |= UART_MCR_RTS;
if (mctrl & TIOCM_DTR)
mcr |= UART_MCR_DTR;
if (mctrl & TIOCM_OUT1)
mcr |= UART_MCR_OUT1;
if (mctrl & TIOCM_OUT2)
mcr |= UART_MCR_OUT2;
if (mctrl & TIOCM_LOOP)
mcr |= UART_MCR_LOOP;
pm_runtime_get_sync(&up->pdev->dev);
up->mcr = serial_in(up, UART_MCR);
up->mcr |= mcr;
serial_out(up, UART_MCR, up->mcr);
pm_runtime_put(&up->pdev->dev);
}
开发者ID:mjduddin，项目名称:B14CKB1RD_kernel_m8，代码行数:23，代码来源:omap-serial.c
示例14: serial8250_console_write
/*
* Print a string to the serial port trying not to disturb
* any possible real use of the port...
*
* The console_lock must be held when we get here.
*/
static void
serial8250_console_write(struct console *co, const char *s, unsigned int count)
{
struct uart_8250_port *up = &serial8250_ports[co->index];
unsigned int ier;
int i;
/*
* First save the UER then disable the interrupts
*/
ier = serial_in(up, UART_IER);
serial_out(up, UART_IER, 0);
/*
* Now, do each character
*/
for (i = 0; i < count; i++, s++) {
wait_for_xmitr(up);
/*
* Send the character out.
* If a LF, also do CR...
*/
serial_out(up, UART_TX, *s);
if (*s == 10) {
wait_for_xmitr(up);
serial_out(up, UART_TX, 13);
}
}
/*
* Finally, wait for transmitter to become empty
* and restore the IER
*/
wait_for_xmitr(up);
serial_out(up, UART_IER, ier);
}
开发者ID:gnensis，项目名称:linux-2.6.15，代码行数:43，代码来源:au1x00_uart.c
示例15: transmit_chars
static void transmit_chars(struct uart_sio_port *up)
{
struct circ_buf *xmit = &up->port.state->xmit;
int count;
if (up->port.x_char) {
#ifndef CONFIG_SERIAL_M32R_PLDSIO /* XXX */
serial_out(up, UART_TX, up->port.x_char);
#endif
up->port.icount.tx++;
up->port.x_char = 0;
return;
}
if (uart_circ_empty(xmit) || uart_tx_stopped(&up->port)) {
m32r_sio_stop_tx(&up->port);
return;
}
count = up->port.fifosize;
do {
serial_out(up, UART_TX, xmit->buf[xmit->tail]);
xmit->tail = (xmit->tail + 1) & (UART_XMIT_SIZE - 1);
up->port.icount.tx++;
if (uart_circ_empty(xmit))
break;
while (!(serial_in(up, UART_LSR) & UART_LSR_THRE));
} while (--count > 0);
if (uart_circ_chars_pending(xmit) < WAKEUP_CHARS)
uart_write_wakeup(&up->port);
pr_debug("THRE...\n");
if (uart_circ_empty(xmit))
m32r_sio_stop_tx(&up->port);
}
开发者ID:AK101111，项目名称:linux，代码行数:37，代码来源:m32r_sio.c
示例16: pnx8xxx_startup
static int pnx8xxx_startup(struct uart_port *port)
{
struct pnx8xxx_port *sport = (struct pnx8xxx_port *)port;
int retval;
retval = request_irq(sport->port.irq, pnx8xxx_int, 0,
"pnx8xxx-uart", sport);
if (retval)
return retval;
serial_out(sport, PNX8XXX_ICLR, PNX8XXX_UART_INT_ALLRX |
PNX8XXX_UART_INT_ALLTX);
serial_out(sport, PNX8XXX_IEN, serial_in(sport, PNX8XXX_IEN) |
PNX8XXX_UART_INT_ALLRX |
PNX8XXX_UART_INT_ALLTX);
spin_lock_irq(&sport->port.lock);
pnx8xxx_enable_ms(&sport->port);
spin_unlock_irq(&sport->port.lock);
return 0;
}
开发者ID:DirtyDroidX，项目名称:android_kernel_htc_m8ul，代码行数:24，代码来源:pnx8xxx_uart.c
示例17: serial_omap_set_mctrl
static void serial_omap_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
struct uart_omap_port *up = to_uart_omap_port(port);
unsigned char mcr = 0, old_mcr;
dev_dbg(up->port.dev, "serial_omap_set_mctrl+%d\n", up->port.line);
if (mctrl & TIOCM_RTS)
mcr |= UART_MCR_RTS;
if (mctrl & TIOCM_DTR)
mcr |= UART_MCR_DTR;
if (mctrl & TIOCM_OUT1)
mcr |= UART_MCR_OUT1;
if (mctrl & TIOCM_OUT2)
mcr |= UART_MCR_OUT2;
if (mctrl & TIOCM_LOOP)
mcr |= UART_MCR_LOOP;
pm_runtime_get_sync(up->dev);
old_mcr = serial_in(up, UART_MCR);
old_mcr &= ~(UART_MCR_LOOP | UART_MCR_OUT2 | UART_MCR_OUT1 |
UART_MCR_DTR | UART_MCR_RTS);
up->mcr = old_mcr | mcr;
serial_out(up, UART_MCR, up->mcr);
pm_runtime_mark_last_busy(up->dev);
pm_runtime_put_autosuspend(up->dev);
if (gpio_is_valid(up->DTR_gpio) &&
!!(mctrl & TIOCM_DTR) != up->DTR_active) {
up->DTR_active = !up->DTR_active;
if (gpio_cansleep(up->DTR_gpio))
schedule_work(&up->qos_work);
else
gpio_set_value(up->DTR_gpio,
up->DTR_active != up->DTR_inverted);
}
}
开发者ID:AD5GB，项目名称:kernel_n5_3.10-experimental，代码行数:36，代码来源:omap-serial.c
示例18: ns16550_serial_putc
DEBUG_UART_FUNCS
#endif
#ifdef CONFIG_DM_SERIAL
static int ns16550_serial_putc(struct udevice *dev, const char ch)
{
struct NS16550 *const com_port = dev_get_priv(dev);
if (!(serial_in(&com_port->lsr) & UART_LSR_THRE))
return -EAGAIN;
serial_out(ch, &com_port->thr);
/*
* Call watchdog_reset() upon newline. This is done here in putc
* since the environment code uses a single puts() to print the complete
* environment upon "printenv". So we can't put this watchdog call
* in puts().
*/
if (ch == '\n')
WATCHDOG_RESET();
return 0;
}
开发者ID:KunYi，项目名称:uboot-samx6i，代码行数:24，代码来源:ns16550.c
示例19: sw_uart_modem_status
static unsigned int sw_uart_modem_status(struct sw_uart_port *sw_uport)
{
unsigned int status = serial_in(&sw_uport->port, SW_UART_MSR);
status |= sw_uport->msr_saved_flags;
sw_uport->msr_saved_flags = 0;
if (status & SW_UART_MSR_ANY_DELTA && sw_uport->ier & SW_UART_IER_MSI &&
sw_uport->port.state != NULL) {
if (status & SW_UART_MSR_TERI)
sw_uport->port.icount.rng++;
if (status & SW_UART_MSR_DDSR)
sw_uport->port.icount.dsr++;
if (status & SW_UART_MSR_DDCD)
uart_handle_dcd_change(&sw_uport->port, status & SW_UART_MSR_DCD);
if (!(sw_uport->mcr & SW_UART_MCR_AFE) && status & SW_UART_MSR_DCTS)
uart_handle_cts_change(&sw_uport->port, status & SW_UART_MSR_CTS);
wake_up_interruptible(&sw_uport->port.state->port.delta_msr_wait);
}
SERIAL_DBG("modem status: %x\n", status);
return status;
}
开发者ID:GREYFOXRGR，项目名称:BPI-M3-bsp，代码行数:24，代码来源:sunxi-uart.c
示例20: serial_omap_set_termios
static void
serial_omap_set_termios(struct uart_port *port, struct ktermios *termios,
struct ktermios *old)
{
struct uart_omap_port *up = (struct uart_omap_port *)port;
unsigned char cval = 0;
unsigned char efr = 0;
unsigned long flags = 0;
unsigned int baud, quot;
switch (termios->c_cflag & CSIZE) {
case CS5:
cval = UART_LCR_WLEN5;
break;
case CS6:
cval = UART_LCR_WLEN6;
break;
case CS7:
cval = UART_LCR_WLEN7;
break;
default:
case CS8:
cval = UART_LCR_WLEN8;
break;
}
if (termios->c_cflag & CSTOPB)
cval |= UART_LCR_STOP;
if (termios->c_cflag & PARENB)
cval |= UART_LCR_PARITY;
if (!(termios->c_cflag & PARODD))
cval |= UART_LCR_EPAR;
baud = uart_get_baud_rate(port, termios, old, 0, port->uartclk/13);
quot = serial_omap_get_divisor(port, baud);
up->calc_latency = (USEC_PER_SEC * up->port.fifosize) / (baud / 8);
up->latency = up->calc_latency;
schedule_work(&up->qos_work);
up->dll = quot & 0xff;
up->dlh = quot >> 8;
up->mdr1 = UART_OMAP_MDR1_DISABLE;
up->fcr = UART_FCR_R_TRIG_01 | UART_FCR_T_TRIG_01 |
UART_FCR_ENABLE_FIFO;
if (up->use_dma)
up->fcr |= UART_FCR_DMA_SELECT;
pm_runtime_get_sync(&up->pdev->dev);
spin_lock_irqsave(&up->port.lock, flags);
uart_update_timeout(port, termios->c_cflag, baud);
up->port.read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
if (termios->c_iflag & INPCK)
up->port.read_status_mask |= UART_LSR_FE | UART_LSR_PE;
if (termios->c_iflag & (BRKINT | PARMRK))
up->port.read_status_mask |= UART_LSR_BI;
up->port.ignore_status_mask = 0;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_PE | UART_LSR_FE;
if (termios->c_iflag & IGNBRK) {
up->port.ignore_status_mask |= UART_LSR_BI;
if (termios->c_iflag & IGNPAR)
up->port.ignore_status_mask |= UART_LSR_OE;
}
if ((termios->c_cflag & CREAD) == 0)
up->port.ignore_status_mask |= UART_LSR_DR;
up->ier &= ~UART_IER_MSI;
if (UART_ENABLE_MS(&up->port, termios->c_cflag))
up->ier |= UART_IER_MSI;
serial_out(up, UART_IER, up->ier);
serial_out(up, UART_LCR, cval);
up->lcr = cval;
up->scr = OMAP_UART_SCR_TX_EMPTY;
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
serial_out(up, UART_DLL, 0);
serial_out(up, UART_DLM, 0);
serial_out(up, UART_LCR, 0);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_B);
up->efr = serial_in(up, UART_EFR);
serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
up->mcr = serial_in(up, UART_MCR);
serial_out(up, UART_MCR, up->mcr | UART_MCR_TCRTLR);
up->scr |= OMAP_UART_SCR_RX_TRIG_GRANU1_MASK;
//.........这里部分代码省略.........
开发者ID:mjduddin，项目名称:B14CKB1RD_kernel_m8，代码行数:101，代码来源:omap-serial.c
注：本文中的serial_in函数示例由纯净天空整理自Github/MSDocs等源码及文档管理平台，相关代码片段筛选自各路编程大神贡献的开源项目，源码版权归原作者所有，传播和使用请参考对应项目的License；未经允许，请勿转载。 |
客服电话
APP下载
官方微信
请发表评论